feat(boot): Add a fast boot cycle and show the count in the title

5_1_Blanton_Script_Boot_Cycle_Fast.ttl is Script 5 with the traffic run
removed from Check Pt8; only 'blanton_traffic_linespeed ps' is left,
for a shorter cycle when the boot count is what matters.

Script 5 sets the window title to 'Reboot Cycle Test : n' or 'Power
Cycle Test : n' every round. Script B and Script 5 pass --force to
qfx5252-stress-usb.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0131orciRKrejchsuDk6UpXk

src/Script_ABC_Blanton/2_Blanton_Script_B.ttl

@@ -60,7 +60,7 @@ usb_dev = groupmatchstr1
 
 wait prompt_sonic_root
 ;sprintf2 cmd "bgctl run qfx5252-stress-usb %s 256M --runtime 86400 --passes 1 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log" usb_dev
-sprintf2 cmd "bgctl run qfx5252-stress-usb %s 256M --runtime %d --passes %d --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log" usb_dev USB_RUNTIME USB_COUNT
+sprintf2 cmd "bgctl run qfx5252-stress-usb %s 256M --runtime %d --passes %d --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log --force" usb_dev USB_RUNTIME USB_COUNT
 sendln cmd
 
 ;wait prompt_sonic_root

src/Script_ABC_Blanton/5_1_Blanton_Script_Boot_Cycle_Fast.ttl

@@ -0,0 +1,412 @@
+include "config.ttl"
+
+flushrecv
+;================================================================
+; Log File Creation
+;================================================================
+gettime str_starttime "%Y%m%d-%H%M%S"
+getdir mdir
+
+if EN_log = 1 then
+    if EN_Cold_Warm_boot = 1 then
+        sprintf2 filename '%s\Logs\%s_%s_%s.log' mdir project_name "Reboot_Cycle" str_starttime
+        logopen filename 0 1 1 1
+    elseif EN_Cold_Warm_boot = 2 then
+        sprintf2 filename '%s\Logs\%s_%s_%s.log' mdir project_name "Power_Cycle" str_starttime
+        logopen filename 0 1 1 1
+    else
+    endif
+endif
+
+cnt_cycle = 0
+
+while 1
+    cnt_cycle = cnt_cycle + 1
+    if EN_Cold_Warm_boot = 1 then
+        sprintf2 log_cycle_msg 'Reboot Cycle Test : %d' cnt_cycle
+        settitle log_cycle_msg
+    elseif EN_Cold_Warm_boot = 2 then
+        sprintf2 log_cycle_msg 'Power Cycle Test : %d' cnt_cycle
+        settitle log_cycle_msg
+    else
+    endif
+    ; ========== Root Login ==========
+    wait prompt_login
+    sendln "admin"
+    wait "Password:"
+    sendln "YourPaSsWoRd"
+    wait prompt_sonic
+    sendln "sudo -i"
+    wait prompt_sonic_root
+    sendln "sleep 10"
+
+    if EN_Cold_Warm_boot = 1 then
+        wait prompt_sonic_root
+        sprintf2 strTitle "echo -e '\033[1;32mReboot Cycle : %d \033[0m'" cnt_cycle
+        sendln strTitle
+    elseif EN_Cold_Warm_boot = 2 then
+        wait prompt_sonic_root
+        sprintf2 strTitle "echo -e '\033[1;32mPower Cycle : %d \033[0m'" cnt_cycle
+        sendln strTitle
+    else
+    endif
+
+    ; ========== Pre Setting ==========
+    ; Make log directory
+    wait prompt_sonic_root
+    sendln "mkdir ./logs"
+
+    ; Setting System Time
+    getdate datestr
+    gettime timestr
+    sprintf2 cmd 'sudo date -s "%s %s"' datestr timestr
+    sendln cmd
+
+    ; ========== FAN SPEED ==========
+    wait prompt_sonic_root
+    sendln "echo 18-0020 > /sys/bus/i2c/drivers/max31790/unbind"
+    wait prompt_sonic_root
+    sendln "sleep .5"
+    wait prompt_sonic_root
+    sendln "echo 18-0020 > /sys/bus/i2c/drivers/max31790/bind"
+    wait prompt_sonic_root
+    sendln "echo 25-0020 > /sys/bus/i2c/drivers/max31790/unbind"
+    wait prompt_sonic_root
+    sendln "sleep .5"
+    wait prompt_sonic_root
+    sendln "echo 25-0020 > /sys/bus/i2c/drivers/max31790/bind"
+
+    wait prompt_sonic_root
+    sprintf2 fan_ctrl_cmd 'fan-speed-control.sh %d' FAN_SPEED
+    sendln fan_ctrl_cmd
+
+    wait "Set all configured fan channels to"
+    sendln "y"
+
+    ; ========== Wait DUT Init ==========
+    include "utils/wait_init.ttl"
+
+    ; ========== DUT Info ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt1 "echo -e '\033[36mCheck Pt1 : DUT Info\033[0m'"
+    sendln strCKPt1
+
+    wait prompt_sonic_root
+    sendln "show boot"
+    wait prompt_sonic_root
+    sendln "show version"
+    wait prompt_sonic_root
+    sendln "fwutil show status"
+    wait prompt_sonic_root
+    sendln "show system-memory"
+    wait prompt_sonic_root
+    sendln "show service"
+    wait prompt_sonic_root
+    sendln "show platform syseeprom"
+    wait prompt_sonic_root
+    sendln "show platform ssdhealth"
+    wait prompt_sonic_root
+    sendln "qfx5252-tpm-version"
+    wait prompt_sonic_root
+    sendln "/usr/sbin/nvme smart-log -H /dev/nvme0"
+    wait prompt_sonic_root
+    sendln "/usr/sbin/smartctl -x /dev/nvme0"
+
+    ; ========== BMC version ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt2 "echo -e '\033[36mCheck Pt2 : BMC Info\033[0m'"
+    sendln strCKPt2
+
+    wait prompt_sonic_root
+    sendln "bmc-first-enroll"
+    wait prompt_sonic_root
+    sendln "bmc-manager version"
+    wait prompt_sonic_root
+    sendln "bmc-manager status"
+
+    ; ========== Load Shell Script ==========
+    wait prompt_sonic_root
+    sendln "source ~/Blanton_Script/blanton_fpga_pcimem.sh"
+    wait prompt_sonic_root
+    sendln "source ~/Blanton_Script/blanton_cb_i2c.sh"
+    wait prompt_sonic_root
+    sendln "source ~/Blanton_Script/blanton_icb_vi2c.sh"
+    wait prompt_sonic_root
+    sendln "source ~/Blanton_Script/blanton_pwr_data.sh"
+    wait prompt_sonic_root
+    sendln "source ~/Blanton_Script/blanton_traffic_linespeed.sh"
+    wait prompt_sonic_root
+    sendln "source ~/Blanton_Script/LTC2980_Margin_Script/margin.sh"
+
+    ; ========== CLEAR PCIE Error ==========
+    include "utils/show_pcie_error_reg_TH6_SWB0.ttl"
+    include "utils/show_pcie_error_reg_TH6_SWB1.ttl"
+    include "utils/show_pcie_error_reg_FPGA.ttl"
+    include "utils/show_pcie_error_reg_BMC.ttl"
+    include "utils/show_pcie_error_reg_DDR.ttl"
+    include "utils/show_pcie_error_reg_I210.ttl"
+    include "utils/show_pcie_error_reg_SSD.ttl"
+
+    wait prompt_sonic_root
+    sendln "/usr/sbin/ras-mc-ctl --summary"
+
+    ; ========== Check PCIE tree + PCIE link status + GET PCIE bandwidth Test ==========
+    include "utils/pcie_bus.ttl"
+
+    ; ========== TAKE DATA ==========
+    include "utils/setup_pmon.ttl"
+    include "utils/show_dmesg.ttl"
+
+    ; ========== 10G/1G MGMT Ping Test ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt3 "echo -e '\033[36mCheck Pt3 : Mgmt Ping Test\033[0m'"
+    sendln strCKPt3
+
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/mgmt_ping_monitor.sh start"
+    wait prompt_sonic_root
+    pause 30
+    sendln "~/Blanton_Script/mgmt_ping_monitor.sh stop"
+    wait prompt_sonic_root
+    sendln "cat ~/Blanton_Script/log/mgmt_ping.log"
+    wait prompt_sonic_root
+    sendln "~/Blanton_Script/mgmt_ping_monitor.sh clear"
+
+    ; ========== NFC Test ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt4 "echo -e '\033[36mCheck Pt4 : NFC Test\033[0m'"
+    sendln strCKPt4
+
+    wait prompt_sonic_root
+    sendln "~/Blanton_Script/nfc_polling.sh start"
+    wait prompt_sonic_root
+    sendln "~/Blanton_Script/nfc_polling.sh status"
+    wait prompt_sonic_root
+    sendln "sleep 20"
+    wait prompt_sonic_root
+    sendln "~/Blanton_Script/nfc_polling.sh stop"
+    wait prompt_sonic_root
+    sendln "~/Blanton_Script/nfc_polling.sh report"
+
+    ; ========== SSD read/write ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt5 "echo -e '\033[36mCheck Pt5 : SSD Test\033[0m'"
+    sendln strCKPt5
+
+    wait prompt_sonic_root
+    sendln "rm -rf /host/hw-eval/jobs/qfx5252-stress-ssd.log"
+    wait prompt_sonic_root
+    sendln "qfx5252-stress-ssd 1G --runtime 30 --passes 2 --write --force --log /host/hw-eval/jobs/qfx5252-stress-ssd.log"
+    wait prompt_sonic_root
+    sendln "cat /host/hw-eval/jobs/qfx5252-stress-ssd.log"
+
+    ; ========== USB read/write ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt6 "echo -e '\033[36mCheck Pt6 : USB Test\033[0m'"
+    sendln strCKPt6
+
+    ; ---- Get USB partition node -> usb_dev ----
+    usb_dev = ''
+    wait prompt_sonic_root
+    sendln 'D=$(bash ~/Blanton_Script/usb_target.sh -o dev 2>/dev/null); echo "<<D""EV=${D:-NONE}>>"'
+    waitregex '<<DEV=([^>]*)>>'
+    usb_dev = groupmatchstr1
+
+    wait prompt_sonic_root
+    sendln "rm -rf /host/hw-eval/jobs/qfx5252-stress-usb.log"
+    wait prompt_sonic_root
+    sprintf2 cmd "qfx5252-stress-usb %s 256M --runtime 30 --passes 2 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log --force" usb_dev
+    sendln cmd
+    wait prompt_sonic_root
+    sendln "cat /host/hw-eval/jobs/qfx5252-stress-usb.log"
+
+    ; ========== BMC USB Test ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt7 "echo -e '\033[36mCheck Pt7 : BMC USB Test\033[0m'"
+    sendln strCKPt7
+
+    wait prompt_sonic_root
+    sendln 'echo "NCMIF=$(ls -d /sys/bus/usb/drivers/cdc_ncm/*/net/* 2>/dev/null | head -n 1 | xargs -r basename)"'
+    ; timeout is GLOBAL and sticky: left at 15, every 'wait' below gives up after
+    ; 15 s instead of blocking, the macro runs ahead of the DUT and the whole
+    ; cycle desynchronises. Restore it BEFORE the branch so both paths are
+    ; covered - the ping block below waits on 'sleep 10', which is already two
+    ; thirds of the 15 s cap on a loaded DUT.
+    timeout = 15
+    waitregex 'NCMIF=[A-Za-z0-9_-]+'
+    ncm_found = result                      ; hold it: 'result' is reused below
+    timeout = 0                             ; restore, both paths
+    if ncm_found = 0 then
+        messagebox 'cdc_ncm interface not found. Ping test skipped.' 'ERROR'
+        goto skip_ping
+    endif
+    strlen matchstr
+    cut_len = result - 6                    ; 'NCMIF=' = 6 chars
+    strcopy matchstr 7 cut_len ncm_if       ; -> ncm_if = "eth2" / "eth3"
+
+    sprintf2 cmd 'ip -br link show %s' ncm_if
+    wait prompt_sonic_root
+    sendln cmd
+
+    wait prompt_sonic_root
+    sendln 'systemctl stop qfx5252-bmc-usb-net-test.service 2>/dev/null || true'
+    wait prompt_sonic_root
+    sendln 'systemctl reset-failed qfx5252-bmc-usb-net-test.service 2>/dev/null || true'
+    sprintf2 cmd 'systemd-run --unit=qfx5252-bmc-usb-net-test --property=Type=exec /usr/bin/ping -I %s -i 1 -W 2 -w 14400 192.168.200.200' ncm_if
+    wait prompt_sonic_root
+    sendln cmd
+    wait prompt_sonic_root
+    sendln "sleep 10"
+    wait prompt_sonic_root
+    sendln "systemctl stop qfx5252-bmc-usb-net-test.service"
+    wait prompt_sonic_root
+    sendln "journalctl -u qfx5252-bmc-usb-net-test.service --no-pager"
+
+:skip_ping
+    timeout = 0                             ; backstop, same as Script B
+
+    ; ========== 100G Port Setting ==========
+    wait prompt_sonic_root
+    sendln "sudo sfputil lpmode off Ethernet513"
+    wait prompt_sonic_root
+    sendln "sudo sfputil lpmode off Ethernet514"
+    wait prompt_sonic_root
+    sendln "config interface -n asic0 startup  Ethernet513"
+    wait prompt_sonic_root
+    sendln "config interface -n asic1 startup  Ethernet514"
+    wait prompt_sonic_root
+    sendln "config save -y"
+
+    ; ========== First Traffic Test ==========
+    ; Silent MAC
+    wait prompt_sonic_root
+    sendln "config feature state lldp disabled"
+    wait prompt_sonic_root
+    sendln "config save -y"
+
+    ; ========== 100G Port Status ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt8 "echo -e '\033[36mCheck Pt8 : Port Status and 15sec Traffic \033[0m'"
+    sendln strCKPt8
+
+    wait prompt_sonic_root
+    sendln "show interfaces status Ethernet513,Ethernet514"
+
+    ; ========== Traffic Test ==========
+    if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
+        wait prompt_sonic_root
+        sendln "blanton_traffic_linespeed ps"
+    elseif SWB_UNIT0 = 1 && SWB_UNIT1 = 0 then
+        wait prompt_sonic_root
+        sendln "blanton_traffic_linespeed ps -u 0"
+    elseif SWB_UNIT0 = 0 && SWB_UNIT1 = 1 then
+        wait prompt_sonic_root
+        sendln "blanton_traffic_linespeed ps -u 1"
+    else
+
+    endif
+
+    ; ========== BER ==========
+    ; PRBS takes the SerDes out of normal operation, so this runs AFTER the
+    ; traffic report. sleep 30 matches blanton_ber.sh BER_INTERVAL - reporting
+    ; earlier reads an interval that has not finished accumulating.
+    wait prompt_sonic_root
+    sprintf2 strCKPt8 "echo -e '\033[36mCheck Pt9 : BER Test \033[0m'"
+    sendln strCKPt8
+
+    if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh init"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh start"
+        wait prompt_sonic_root
+        sendln "sleep 30"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh report"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh stop"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh clear"
+    elseif SWB_UNIT0 = 1 && SWB_UNIT1 = 0 then
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh init -u 0"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh start -u 0"
+        wait prompt_sonic_root
+        sendln "sleep 30"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh report -u 0"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh stop -u 0"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh clear -u 0"
+    elseif SWB_UNIT0 = 0 && SWB_UNIT1 = 1 then
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh init -u 1"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh start -u 1"
+        wait prompt_sonic_root
+        sendln "sleep 30"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh report -u 1"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh stop -u 1"
+        wait prompt_sonic_root
+        sendln "./Blanton_Script/blanton_ber.sh clear -u 1"
+    else
+
+    endif
+
+    ; ========== NVME Err Info ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt9 "echo -e '\033[36mCheck Pt10 : NVME Err Info \033[0m'"
+    sendln strCKPt9
+
+    wait prompt_sonic_root
+    sendln "/usr/sbin/nvme smart-log -H /dev/nvme0"
+    wait prompt_sonic_root
+    sendln "/usr/sbin/smartctl -x /dev/nvme0"
+
+    ; ========== TAKE DATA ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt10 "echo -e '\033[36mCheck Pt11 : Platform Data \033[0m'"
+    sendln strCKPt10
+    include "utils/setup_pmon.ttl"
+
+    wait prompt_sonic_root
+    sprintf2 strCKPt12 "echo -e '\033[36mCheck Pt12 : Dmesg_i2c \033[0m'"
+    sendln strCKPt12
+    include "utils/show_dmesg.ttl"
+
+    ; ========== Check PCIE error counters ==========
+    wait prompt_sonic_root
+    sprintf2 strCKPt13 "echo -e '\033[36mCheck Pt13 : PCIE Error Counters \033[0m'"
+    sendln strCKPt13
+    include "utils/show_pcie_error_reg_TH6_SWB0.ttl"
+    include "utils/show_pcie_error_reg_TH6_SWB1.ttl"
+    include "utils/show_pcie_error_reg_FPGA.ttl"
+    include "utils/show_pcie_error_reg_BMC.ttl"
+    include "utils/show_pcie_error_reg_DDR.ttl"
+    include "utils/show_pcie_error_reg_I210.ttl"
+    include "utils/show_pcie_error_reg_SSD.ttl"
+
+    wait prompt_sonic_root
+    sendln "/usr/sbin/ras-mc-ctl --summary"
+
+    ; ========== Show Power on uptime ==========
+    wait prompt_sonic_root
+    sendln "show uptime"
+
+    ; ========== Show Power on uptime ==========
+    if EN_Cold_Warm_boot = 1 then
+        wait prompt_sonic_root
+        sendln "reboot"
+    elseif EN_Cold_Warm_boot = 2 then
+        wait prompt_sonic_root
+        sendln "pcimem /sys/bus/pci/devices/0000:05:00.0/resource0 0x480 w 0xD0000"
+    else
+    endif
+
+
+    wait "Booting in blind mode"
+endwhile

src/Script_ABC_Blanton/5_Blanton_Script_Boot_Cycle.ttl

@@ -22,6 +22,14 @@ cnt_cycle = 0
 
 while 1
     cnt_cycle = cnt_cycle + 1
+    if EN_Cold_Warm_boot = 1 then
+        sprintf2 log_cycle_msg 'Reboot Cycle Test : %d' cnt_cycle
+        settitle log_cycle_msg
+    elseif EN_Cold_Warm_boot = 2 then
+        sprintf2 log_cycle_msg 'Power Cycle Test : %d' cnt_cycle
+        settitle log_cycle_msg
+    else
+    endif
     ; ========== Root Login ==========
     wait prompt_login
     sendln "admin"
@@ -207,7 +215,7 @@ while 1
     wait prompt_sonic_root
     sendln "rm -rf /host/hw-eval/jobs/qfx5252-stress-usb.log"
     wait prompt_sonic_root
-    sprintf2 cmd "qfx5252-stress-usb %s 256M --runtime 30 --passes 2 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log" usb_dev
+    sprintf2 cmd "qfx5252-stress-usb %s 256M --runtime 30 --passes 2 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log --force" usb_dev
     sendln cmd
     wait prompt_sonic_root
     sendln "cat /host/hw-eval/jobs/qfx5252-stress-usb.log"