etwenandClaude Opus 5
9cdd651d79
mlucas-avx2 was backgrounded with '&' in the login shell, so it belonged
to that one terminal. Close Tera Term, drop the console, or reconnect on
a different session and the load was gone - and 'jobs' from the new
session showed nothing to say so. A multi-day soak could spend most of
its length with an idle CPU while the thermal numbers looked fine.
Script B now starts it as a transient unit:
systemd-run --unit=mlucas-amm --property=Type=exec \
--property=Restart=always --property=RestartSec=2 ...
The log is truncated once with '>' before the unit starts and appended
with '>>' inside it, so a restart adds to the run instead of erasing it.
'systemctl is-active mlucas-amm' now sits beside 'jobs', both in the
one-shot check and in every pass of the monitor loop. The old '&' line is
kept commented out above the new one to fall back to.
Script C has the matching stop. utils/kill_all_process.ttl is only
"kill $(jobs -p)" and a systemd unit is not a shell job, so without this
the load would have run through the post-test snapshot and into the next
test - every temperature and power reading taken at full load, with
nothing in 'show interfaces status' to reveal it. mlucas_amm_log is
copied to /host/hw-eval/jobs/ with the other stress logs.
Two values move into config.ttl:
EN_timestamp feeds logopen's 5th argument in Script A, so the
per-line timestamp is a knob rather than a literal 1
BMC_USB_RUNTIME feeds Script B's ping unit; it was hard-coded to
-w 14400 (4 h), which no longer matched the soak
lengths the SSD and USB knobs were being set to
SSD_RUNTIME and USB_RUNTIME also go 600 -> 3600, so the shipped default
is a one hour stress rather than the ten minutes V1.1.7 went out with.
--runtime is still the job's overall limit; COUNT does not multiply it.
Script A's Version History carries the V1.1.8 entries for all of this.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_014RetWKFZFG1ZHcitQAyhwM
35 lines
1.6 KiB
Turtle
35 lines
1.6 KiB
Turtle
;================================================================
|
|
; User Configuration
|
|
;================================================================
|
|
project_name = "Blanton"
|
|
strTestcase="ENV" ;ENV,EMC,Margin...etc
|
|
|
|
EN_Margin = 0 ; 1: Enable Margin Test, 0: Disable Margin Test
|
|
EN_log = 1 ; 1: Enable log, 0: Disable log
|
|
EN_timestamp = 1 ; 1: Enable timestamp in log, 0: Disable timestamp in log
|
|
|
|
;================================================================
|
|
; FAN_SPEED
|
|
;================================================================
|
|
FAN_SPEED = 100
|
|
;================================================================
|
|
; Switch Unit Population
|
|
;================================================================
|
|
SWB_UNIT0 = 1 ; 1 = this DUT has switch unit 0, wait for it ; 0 = skip
|
|
SWB_UNIT1 = 1 ; 1 = this DUT has switch unit 1, wait for it ; 0 = skip
|
|
|
|
;================================================================
|
|
; Stress_Test
|
|
;================================================================
|
|
SSD_RUNTIME = 3600 ; Unit seconds, 3600 = 1 hour
|
|
SSD_COUNT = 240 ; Total time = SSD_RUNTIME * SSD_COUNT
|
|
USB_RUNTIME = 3600 ; Unit seconds, 3600 = 1 hour
|
|
USB_COUNT = 240 ; Total time = USB_RUNTIME * USB_COUNT
|
|
BMC_USB_RUNTIME = 172800 ; Unit seconds, 172800 = 2 days
|
|
|
|
;================================================================
|
|
; Prompt Definitions
|
|
;================================================================
|
|
prompt_login = "sonic login:"
|
|
prompt_sonic = "admin@sonic:~$"
|
|
prompt_sonic_root = "root@sonic:~#" |