Three new tools and one fix to an old one.
blanton_ber.sh - PRBS BER across every cabled port, init/start/report/
stop/clear, -u 0|1|all. A lane passes only below 1e-6 (equal to the
threshold fails). report ends with a per-unit summary carrying the worst
lane, so an all-PASS run still shows how much margin there was. init
checks every lane locked, because an unlocked lane still reports a BER
and it is a meaningless one. Script C runs it after the traffic report,
following SWB_UNIT0/SWB_UNIT1 like the traffic block does.
blanton_tr518.sh - the built-in packet test, used to load the rails
before measuring power. start settles 120s so the reading afterwards is
loaded rather than mid-ramp. stop sends port cd lb=none and nothing else,
exactly what the bench procedure does - l2 learning and test mode are
left as start set them, and stop says so instead of quietly leaving the
box in a state nobody asked about.
TH6_SWB{0,1}_power_readback.sh - 19 rails, V x I and total. These read
the two sensor tables ONCE. The previous version read them per rail: 38
invocations of a slow CLI at 38 different instants, so the "total" was a
sum of readings seconds apart - and under load the currents move (TH6_CORE
186 A -> 636 A). A rail missing from the table now warns on stderr instead
of silently contributing 0 W.
blanton_traffic_linespeed.sh - ce0 (VLAN 138) joins the test. It has no
loopback partner and a switch never sends a frame back out its ingress
port, so a tx burst was one round trip and then silence. init now sets an
ingress mirror of ce0 back to itself; the mirrored copy is not
egress-filtered, so packets keep lapping until stop turns the mirror off.
stop is what ends it - removing the VLAN membership does not, because the
copy never consulted the VLAN. TL_CE_MODE also drops to 'self': ps ce
shows one ce port per unit and a unit-0-only burst returned on unit 0.
Read as cross-unit, both links dying would still report PASS (0 == 0).
Fixes a parser bug worth remembering: bcmcmd returns CRLF, and the BER is
the last token on its line, so the CR stayed glued to the number. Every
lane read as NA, and printing the CR sent the cursor to column 1 so the
RESULT column overwrote the start of the row. One stray \r, two symptoms.
Not yet verified on hardware, all called out in the release notes: the
ce0 mirror (destport == srcport may be refused), the 120s settle (tr 518
may be time-limited), and 'test mode nr=no' on stop.
Script A -> V1.1.0.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_014RetWKFZFG1ZHcitQAyhwM
Script B's monitoring loop had no pause at all - each round started the
instant the last one ended, so an overnight soak filled the log with
near-identical samples taken seconds apart. The section was even labelled
"Get data every 10mins" while running with no delay whatsoever.
The loop now ends each round with pause 60 and prints both job lists:
bgctl list for the platform job runner, jobs for anything the macro
backgrounded in that shell. A stress job that dies mid-soak shows up as a
shorter list on the next round instead of going unnoticed until the end.
60s is still hard-coded and the Status sheet asks for 10 minutes, so the
Phase 3 item stays open - this makes the loop sane, it does not close it.
Also adds docs/LTC2980_channel_map.csv: the nine settings/*.conf flattened
into one Board,CONN,Ch,NetName,Vnom sheet, generated by
tools/gen_channel_map.sh. The CSV is output, not source. NC channels are
kept as NC/- because the channel number is also the PMBus page - dropping
the gaps would shift every channel after them.
Two things the merged table makes visible: SWB0 and SWB1 carry identical
net names and voltages (only the bus and CB_I2C_CH differ), so those are
two copies that can drift apart silently; and there are exactly 8 NC
channels, all on CONN14/CONN15.
tools/100G_PRBS.txt, TR518.txt and fan_ctrl.txt join the existing
traffic_loopback_*.txt references. TR518 is not scripted yet and cannot
share the hardware with blanton_traffic_linespeed - both drive port
loopback and L2 learning.
Script A -> V1.0.10.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_014RetWKFZFG1ZHcitQAyhwM
etwenandClaude Opus 5