feat(multiphase): Add a way back from a margin without a power cycle

blanton_multiphase_margin.sh gains 'normal', which returns all 38 rails
to their nominal set point from tools/Multiphase_Normal.txt. Same rails,
same per-rail reporting, same -u 0|1|all as the margin profiles.

Until now the tool could apply high3/low3/comboA/comboB and commit with
save, but had no way to undo. That left a power cycle as the only exit -
and worse, a save run while still margined would have written the offsets
into NVM, which a power cycle does not undo either.

Emitted commands were diffed against the source file: argv identical.

The nominal labels in the source carry extra text ("0.900V (nominal)",
"0.8V(nominal) , 0.8591V with load line"); the per-rail line prints just
the voltage so the column matches the other profiles. The load-line note
is kept as a comment above the data block, because reading 0.859 V back
from TH6_CORE after 'normal' looks like a failed write and is not one.

Script A -> V1.1.7.

Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_014RetWKFZFG1ZHcitQAyhwM

ARCHITECTURE.md

@@ -120,6 +120,7 @@ Blanton_TTL_Script/
 │   ├── Blantons_FPGA_Registers_draft.docx # 同上，客戶原始 docx
 │   ├── Blantons_FPGA_Registers_Map_draft.xlsx
 │   ├── Blantons_PCIe_AER_and_DDR_EDAC_checks.pdf  # AER / EDAC 檢查點依據
+│   ├── ADPM12200CMLZxx_DS_Datasheet_*.pdf # PDB brick 手冊（PAGE 與 DIRECT 係數的來源）
 │   ├── Blanton_Test_Flow.drawio           # A/B/C + 熱安規四支的測試流程圖（draw.io）
 │   ├── LTC2980_channel_map.csv            # 9 個 settings/*.conf 合併：Board,CONN,Ch,NetName,Vnom（144 列）
 │   ├── TTL_Script_Blanton_Status_20260814.xlsx
@@ -135,6 +136,8 @@ Blanton_TTL_Script/
 │   ├── 100G_PRBS.txt                      # 100G PRBS 原始指令（port_prbs_monitor.sh 的來源）
 │   ├── TR518.txt                          # 內建封包測試 tr 518 → blanton_tr518.sh
 │   ├── BER_Test.txt                       # 全機 PRBS BER 指令 → blanton_ber.sh
+│   ├── Multiphase_{high3,low3,comboA,comboB,Save}.txt  # → blanton_multiphase_margin.sh
+│   ├── Multiphase_Netname                 # 38 條軌的 net 名稱（區塊順序對應）
 │   ├── 100G_Traffic.txt                   # ce0 VLAN 138 打流 → blanton_traffic_linespeed.sh
 │   ├── fan_ctrl.txt                       # MAX31790 unbind/bind + fan-speed-control.sh 30
 │   └── gen_channel_map.sh                 # settings/*.conf → docs/LTC2980_channel_map.csv（需 gawk）
@@ -190,6 +193,8 @@ Blanton_TTL_Script/
             │                              #   eth0→TARGET_10G、eth1→TARGET_1G，兩張卡同時持續 ping
             ├── port_prbs_monitor.sh       # 100G uplink PRBS 測試（bcmcmd phy diag）
             ├── blanton_ber.sh             # 全機 SerDes BER 掃描（phydiag prbs / prbsstat）
+            ├── blanton_multiphase_margin.sh # 多相 VRM margin（原生 i2c，38 條軌）
+            ├── pwr_brick.sh               # PDB / CPB power brick 讀值（VI2C ch4）
             ├── nfc_polling.sh             # NFC tag 背景輪詢 + PASS/FAIL 統計
             ├── blantons_nfc_validate.py   # NFC/NCI 驗證工具（廠商提供，未修改）
             ├── blanton_tr518.sh           # TR518 封包測試，量功耗前的負載來源
@@ -206,6 +211,7 @@ Blanton_TTL_Script/
                 ├── settings/*.conf        # 一個 .conf = 一顆 LTC2980（CB + SWB0/1 × CONN13~16）
                 ├── profiles/*.conf        # 16-ch 批次組合。SWB 為 per-CONN：
                 #                            #   combo_SWB_CONN13~16_{high,low}（百分比對應該片的軌）
+                #                            #   comboA/comboB_{CB,SWB_CONN13~16}（互補棋盤配對）
                 #                            #   通用：high3/5、low3/5、normal、all_off
                 ├── script/*_all.sh        # 跨 9 顆 LTC2980 的批次 status / apply / save
                 ├── Ref/margin_command_trace.md  # 指令追蹤參考（SWB 章節已標過期，見文件內警告）
@@ -357,17 +363,18 @@ PROFILE_CHANNELS=( "0:high:8" "1:low:8" ... )   # "channel:operation:change_perc
 
 | 模組 | 進入點 | 功能 |
 |------|--------|------|
-| **Script A（Pre-test）** | `1_Blanton_Script_A.ttl` V1.1.4 | root 登入 → `date -s` 對時 → 清 job log → **收掉前一輪殘留**（`hw-test-session finish` → `bgctl reset --yes` → `bgctl stop --all` → `bgctl list` 確認清空）→ `hw-test-session start` → **設定風扇轉速** → **等資料面就緒**（`wait_init.ttl`）→ DUT 清單（boot/version/fwutil/syseeprom/ssdhealth/TPM/NVMe）→ BMC enroll + version/status → source bash 工具 → 清/讀 7 組 PCIe AER + `ras-mc-ctl --summary` → `lspci` → margin → PMON → dmesg → **10G/1G 管理網路 ping** → **NFC 基線**（start → 30s → stop → report）→ 100G uplink 設定與狀態 → **一輪流量基線** → `show uptime` |
+| **Script A（Pre-test）** | `1_Blanton_Script_A.ttl` V1.1.6 | root 登入 → `date -s` 對時 → 清 job log → **收掉前一輪殘留**（`hw-test-session finish` → `bgctl reset --yes` → `bgctl stop --all` → `bgctl list` 確認清空）→ `hw-test-session start` → **設定風扇轉速** → **等資料面就緒**（`wait_init.ttl`）→ DUT 清單（boot/version/fwutil/syseeprom/ssdhealth/TPM/NVMe）→ BMC enroll + version/status → source bash 工具 → 清/讀 7 組 PCIe AER + `ras-mc-ctl --summary` → `lspci` → margin → PMON → dmesg → **10G/1G 管理網路 ping** → **NFC 基線**（start → 30s → stop → report）→ 100G uplink 設定與狀態 → **一輪流量基線** → `show uptime` |
-| **Script B（Stress）** | `2_Blanton_Script_B.ttl` | `mlucas-avx2 -cpu 0:15` + `bgctl run` 的 `memtester` / SSD / USB 壓力 + BMC DDR（`bmc-manager run memtester`）→ BMC USB net test（探測 cdc_ncm 介面，`systemd-run` 掛 4 小時 ping）→ 啟動 mgmt ping 監控 → **啟動 NFC 輪詢** → `jobs` / `bgctl list` → traffic（依 `SWB_UNIT`）→ `while 1` 每輪 PMON + `bgctl list`/`jobs` + `pause 60`（**V1.1.4 起 margin 不在迴圈內**）|
+| **Script B（Stress）** | `2_Blanton_Script_B.ttl` | `mlucas-avx2 -cpu 0:15` + `bgctl run` 的 `memtester` / SSD / USB 壓力（v1.1.5 起 SSD/USB `--runtime 86400`、BMC memtester 不帶次數 = 跑到被停） + BMC DDR（`bmc-manager run memtester`）→ BMC USB net test（探測 cdc_ncm 介面，`systemd-run` 掛 4 小時 ping）→ 啟動 mgmt ping 監控 → **啟動 NFC 輪詢** → `jobs` / `bgctl list` → traffic（依 `SWB_UNIT`）→ `while 1` 每輪 PMON + `bgctl list`/`jobs` + `pause 60`（**V1.1.4 起 margin 不在迴圈內**）|
-| **Script C（Post-test）** | `3_Blanton_Script_C.ttl` | `kill $(jobs -p)` + `bgctl stop --all` / `reset` + 停 BMC USB unit、mgmt ping 與 **NFC 輪詢** → PMON + dmesg → 7 組 AER + `ras-mc-ctl` → BMC USB `journalctl` → `ip -s link show eth0/eth1` → `cat` mlucas log → **NFC `report`** → traffic `stop` + `report` → **BER 掃描**（依 `SWB_UNIT`）→ NVMe 健康 → `show reboot-cause` → **margin 掃描**（`EN_Margin`，V1.1.4 由 Script B 移來）→ `uptime` → **job log 複製到 USB（帶時戳）** → `exit` + wait『Script done』→ `hw-test-session finish` |
+| **Script C（Post-test）** | `3_Blanton_Script_C.ttl` | `kill $(jobs -p)` + `bgctl stop --all` / `reset` + 停 BMC USB unit、mgmt ping 與 **NFC 輪詢** → PMON + dmesg → 7 組 AER + `ras-mc-ctl` → BMC USB `journalctl` **寫進 `log/bmc_usb_net.log`**（不再印在 console） → `ip -s link show eth0/eth1` → `cat` mlucas log → **NFC `report`** → traffic `stop` + `report` → **BER 掃描**（依 `SWB_UNIT`）→ NVMe 健康 → `show reboot-cause` → **margin 掃描**（`EN_Margin`，V1.1.4 由 Script B 移來）→ `uptime` → **job log 複製到 USB（帶時戳）** → `exit` + wait『Script done』→ `hw-test-session finish` |
 | **Script 4（Thermal / Safety）** | `4_Blanton_Script_thermal_safety.ttl` | **獨立腳本，不接 A→B→C。** Script A 式的環境建立（登入 / session / 風扇 / `wait_init` / DUT 清單 / BMC / PCIe 清除 / `pcie_bus` / PMON / dmesg）→ **滿載**（`mlucas-avx2 -cpu 0:15` 背景 + `blanton_tr518.sh start`）→ `while 1`：PMON + `TH6_SWB0/1_power_readback.sh` + `bgctl list` / `jobs`，`pause 60`。**沒有收尾段** —— 中斷後 DUT 仍在 `port cd lb=mac` / `l2 learn off` / `test mode nr=yes`，要手動 `blanton_tr518.sh stop` |
-| **SWB loopback 流量** | `blanton_traffic_linespeed <sub> [-u 0\|1\|all]` | `init`（VLAN 30..137，成對 `cdN`/`cdN+32`）→ `clear` → `start`（`tx 100 length=512`）→ `stop` → `report`（per-pair TX/RX 交叉比對 PASS/FAIL）；另有 `ps`（link/speed）與 `run`（一條龍）。**V0.6.0 起含 100G uplink `ce0`**（VLAN 138）：它沒有 loopback 對象，靠 **ingress mirror 打回自己**維持循環，`report` 最後一列就是它，底下再接一份跨 unit summary |
+| **SWB loopback 流量** | `blanton_traffic_linespeed <sub> [-u 0\|1\|all]` | `init`（VLAN 30..137，成對 `cdN`/`cdN+32`）→ `clear` → `start`（`tx 200 length=324 PatternRandom=yes`，v0.7.0 起）→ `stop` → `report`（per-pair TX/RX 交叉比對 PASS/FAIL）；另有 `ps`（link/speed）與 `run`（一條龍）。**V0.6.0 起含 100G uplink `ce0`**（VLAN 138）：它沒有 loopback 對象，靠 **ingress mirror 打回自己**維持循環，`report` 最後一列就是它，底下再接一份跨 unit summary |
 | **FPGA 暫存器存取** | `cb_fpga <fn> <addr> [data]`、`fpga_rescan` | pcimem 打 `resource0` + BAR 相對 offset，32-bit word；BDF 於 source 時自動偵測；`pmc/icb/swb0/swb1_fpga` 走 VSPI 窗口 |
 | **CB I2C / PMBus** | `cb_i2c_init/scan/read/write`、`cb_pmbus_read/write/linear16` | FPGA F3 OpenCores master，**讀用 Repeated START**（SMBus/PMBus 裝置必需） |
 | **ICB / PDB 存取** | `vi2c_init/scan/read/write`、`vi2c_scan_all` | CB F3 VI2C proxy，~3.3 ms/reg，取代 VSPI 的 ~18 ms/reg（後者會踩 SMBus 25–35 ms timeout） |
 | **溫度** | `temp_cb` / `temp_icb` / `temp_all` | TMP75（12-bit 左靠齊 ×0.0625）、TMP432（含 RANGE bit 的 −64 偏移、remote1/2） |
 | **電源資料** | `pwr_data` / `pwr_data_pdb` / `pwr_pdb_id` | SWB VRM 全軌 Vin/Vout/Iout/Temp 對齊表；MP29816 解析度**執行期從 `MFR_VOUT_SCALE_LOOP` 讀**，不寫死 |
 | **電壓 Margin** | `margin_init/status/set/apply_profile/save` + `*_all.sh` | 9 顆 LTC2980（CB CONN13、SWB0/1 CONN13~16）批次 high/low margin 與狀態掃描。`VNOM` 為 Blanton 實測中位數（2026-08-30）；SWB 的 profile 是 per-CONN，套錯 CONN 會 margin 到錯的軌且不報錯。v2.6.0 起 SWB 路徑真正接上共用 cb_i2c 後端，並有 `margin_swb_info/probe/scan/reset/sem` 除錯包裝 |
+| **Multiphase VRM margin** | `blanton_multiphase_margin.sh {high3\|low3\|comboA\|comboB\|save} [-u 0\|1\|all]` | 兩片 SWB 的多相控制器（**不是** `margin.sh` 管的 LTC2980），走原生 i2c bus：SWB0 = `/dev/i2c-13`+`-15`、SWB1 = `-14`+`-16`。每片 19 條軌、共 38 條，逐條印 `SWB0_0V9_ANLG0 - 0.930V Configure Done`。`save` 沒有 per-rail 對應，只印 `Multiphase Save All`。⚠️ `save` 是 `STORE_USER_ALL`（0x15，TH6 core 用 0x17）**永久寫 NVM**；⚠️ 與 `margin.sh` 從兩側摸同一批軌，**不可同時用** |
 | **Margin 寫 NVM** | `margin_save` / `margin_save all` / `margin_save blanton` | ⚠️ 永久寫入。`0x15` 送 PMBus **send-byte**（不帶 data byte）。`all` = 依 `settings/` 走 9 顆、跑完還原原本載入的板子；`blanton` = 本平台捷徑，18 顆全走原生 i2c bus（`MARGIN_BLANTON_STORE` 表），不需 `margin_init`。每筆之間 `MARGIN_STORE_SETTLE`（0.5s），工具**不 poll busy bit** |
 | **管理網路 ping** | `mgmt_ping_monitor.sh {start\|stop\|status\|fg\|tail\|clear\|summary}` | 一輪 = 10G leg + 1G leg，各自 `ip address/route replace` 後 `ping -I <if>` 打自己的對端；兩張卡都保持 up。每 leg 記 `ip -s link show` 與該卡的 TX/RX packet delta，另出一行可 grep 的 `RESULT` |
 | **BMC 監控** | `bmc_monitor.sh {start\|stop\|status\|fg\|tail\|clear}` | 由 host 端 `bmc-manager run` 週期取樣 `free -m`，另加一組 **I2C 寫入/讀回圖樣測試**（bus 1、addr 0x41、offset 0x00C0，寫 `55AA55AA` 讀回、再寫 `AA55AA55` 讀回）。B 啟動、C 停止並 `cat log/bmc_poll.log` |
@@ -375,6 +382,7 @@ PROFILE_CHANNELS=( "0:high:8" "1:low:8" ... )   # "channel:operation:change_perc
 | **100G PRBS** | `port_prbs_monitor.sh {start [both\|a\|b]\|stop\|status\|report\|clear}` | 兩個 uplink 各一個 worker，可同時或單獨跑。setup（`lpmode off` → `prbs set` → `prbsstat STArt`）→ 週期 `prbs get`（判定）+ `prbsstat Ber`（只記錄）→ teardown（`STOp` + `prbs clear`）。輸出含 `PRBS OK!` 才算 PASS。**⚠️ A/B/C 的呼叫目前註解掉** |
 | **SerDes BER 掃描** | `blanton_ber.sh {init\|clear\|start\|stop\|report} [-u 0\|1\|all]` | 全機每個對接 port 的 PRBS BER：`prbs set p=3` + `prbs get`（確認每條 lane 都鎖上）→ `prbsstat STArt Interval=30` →（等一個 interval）→ `prbsstat Ber` → `STOp` → `prbs clear`。`report` 一列一條 lane，**BER < 1e-6 才 PASS**，最後跨 unit 的 summary 帶最差 lane。⚠️ PRBS 期間 link 顯示 DOWN、不過流量 |
 | **TR518 負載** | `blanton_tr518.sh {start\|stop} [-u 0\|1\|all]` | `port cd lb=mac` → `l2 learn off` → `test mode nr=yes` → `tr 518 ... testphase=1`，然後 settle `TR_SETTLE_SEC`（120s）再讓人量功耗。`stop` 只送 `port cd lb=none`（照 `TR518.txt`），L2 學習與 test mode **不會還原**，`TR_RESTORE_*=1` 才會 |
+| **PDB / CPB brick** | `pwr_brick.sh show [-r]` | 5 顆 brick 的 Vin / Iin / Vout / Iout / Temp（SWB0 `0x62`/`0x63`、SWB1 `0x60`/`0x61`、CPB `0x26`）。四顆 ADPM12200 **每個量各自一個 PMBus PAGE**（Vin 9、Iin 10、Vout 2、Iout 14、Temp 18），讀之前一定要先寫 PAGE —— `blanton_pwr_data.sh` 完全沒寫，所以整張 PDB 表都是 NA。換算用手冊 DIRECT 公式 `X=(1/m)(Y×10⁻ᴿ−b)`。每個值重讀到通過三道檢查為止（非 `0xFFFF`、非 `0x0000`、落在合理範圍）—— 這條匯流排**只壞高位元組**，`11.98 V` 會變成 `32.00 V`，全一過濾擋不住 |
 | **SWB 軌功耗** | `TH6_SWB{0,1}_power_readback.sh` | 讀 `show platform voltage/current` **各一次**，19 條軌 V×I 與總功耗。舊版每軌各讀一次（38 次呼叫、每軌不同時刻），總和是不同瞬間的加總 |
 | **NFC 讀取輪詢** | `nfc_polling.sh {start\|stop\|status\|tail\|report\|clear\|fg}` | 背景重複跑 `blantons_nfc_validate.py`，每輪追加一行機器可讀的 `RESULT=`（PASS/FAIL 取自工具自己的摘要行，兩者皆無則 **ERROR**，與 FAIL 分開計數）。`start` 會先清空 log；`report` **只讀 log，polling 中隨時可跑**，並標示 `RUNNING` 免得快照被當最終結果。`tail` **不 follow** |
 | **USB 目標偵測** | `usb_target.sh [-o dev\|mnt\|both\|id] [-n] [-r sec]` | 找出插入的 USB 儲存裝置，排除 `/` 與 `/host` 的底層碟（本平台可能從 USB DOM 開機），多顆時拒絕猜；掛載時會驗證真的可寫 |
@@ -804,6 +812,26 @@ margin status、全部 VRM 軌的 Vin/Vout/Iout/Temp、CB + ICB 溫感讀值，
   **`sleep 120` 的方向還沒驗證** —— 若 `tr 518` 的流量是有時限的（參數含 `runtime=1`、
   `CheckDataTime=200`），等 120 秒可能量到已經降下來的值，要上機比對 0s / 30s / 120s 三次；
   TTL 尚未呼叫它。
+- **`--runtime 86400` 是 24 小時的上限，不是「永遠」**：超過一天的 soak，SSD 與 USB 壓力會在
+  第 24 小時安靜結束，剩下的時間那兩項是閒置的。Script B 每輪都印 `bgctl list`，數量變少會看得到，
+  但**沒有任何東西會主動報警**。真的要跑更久，得把數字改大或加一段重啟 job 的邏輯。
+- **BMC USB 的 service log 只剩隨身碟一份**：Script C 把 `journalctl` 導進
+  `log/bmc_usb_net.log` 再 `cp` 到 job 目錄，**不再印在 master console log**。
+  那個 `cp` 沒有檢查回傳值（`nfc_polling.log` 檔名打錯那次就是這樣安靜失敗的），
+  失敗的話這份 log 就完全消失。要嘛在 `cp` 之後補一次 `ls` 驗證，要嘛保留一份
+  `cat` 到 console。
+- **`READ_VIN` / `READ_IIN` 不在 ADPM12200 手冊的 Table 3 裡**：`pwr_brick.sh` 讓它們沿用
+  Voltage / Current 那兩組係數。50 V 輸入算得出來、數量級也對，但**手冊沒有明說**。要定案
+  得找 ADI 確認，或找一個能獨立比對輸入電壓的量測點（`READ_VOUT` 就是靠 `show platform
+  voltage` 的 `PDB_IBC_*` 對上的）。
+- **VI2C 沒有硬體號誌**（`vi2c_muxsel` 的 help 自己寫了「VI2C has no SEM_REG」），而平台的
+  sensor 驅動會週期性讀同一批 PDB 裝置。`pwr_brick.sh` 用「重讀到合理為止」繞過去，但根本
+  問題沒解：`_vrd` 裡的 `_vwait` 逾時後仍然回傳半成品，呼叫端也沒檢查它的回傳值。修
+  `blanton_icb_vi2c.sh` 會影響所有走 VI2C 的工具（ICB 溫感、風扇、EEPROM），值得先確認
+  是不是跟 pmon 競爭再動。
+- **`blanton_multiphase_margin.sh` 與 `margin.sh` 沒有互斥機制**：兩支從不同側（原生 i2c vs
+  LTC2980 PMBus）摸同一批軌，各自都假設自己是唯一的寫入者。目前只靠文件與 help 提醒，
+  沒有任何執行期檢查。
 - **Script 4 沒有收尾段**：`while 1` 之後就是檔案結尾，中斷時 DUT 停在 `port cd lb=mac` /
   `l2 learn off` / `test mode nr=yes`，而且 `mlucas-avx2` 還在背景跑。要手動
   `blanton_tr518.sh stop` + `kill`，否則下一輪任何測試都在被污染的狀態上開始

CLAUDE.md

@@ -9,7 +9,7 @@ DUT 端的取數能力由一組 **bash 工具庫** 提供（CB FPGA `pcimem` →
 
 完整架構見 [ARCHITECTURE.md](ARCHITECTURE.md)。
 
-**目前狀態（2026-08-31）**：Script A 為 **V1.1.4**（A 集中記錄所有 TTL 的變更）。涵蓋
+**目前狀態（2026-09-02）**：Script A 為 **V1.1.6**（A 集中記錄所有 TTL 的變更）。涵蓋
 PCIe AER / DDR EDAC / PMON+TPM / 電壓 margin（9 顆 LTC2980）/ SWB loopback 線速流量 /
 10G+1G 管理網路 ping / BMC DDR 與 USB / NVMe 健康，壓力層走平台的 `bgctl`。
 switch unit 數量由 `config.ttl` 的 `SWB_UNIT0` / `SWB_UNIT1` 宣告，風扇轉速由 `FAN_SPEED` 指定
@@ -26,7 +26,7 @@ NFC tag 讀取由 `nfc_polling.sh` 背景輪詢（A 做基線、B 起、C 停並
 另有 **`4_Blanton_Script_thermal_safety.ttl`**（熱 / 安規，**獨立跑不接 A→B→C**，滿載後每分鐘
 取 PMON + 兩片 SWB 的軌功耗；**沒有收尾段**，中斷後要手動 `blanton_tr518.sh stop`）。
 流程圖：`docs/Blanton_Test_Flow.drawio`。
-最後一次發布是 **V1.1.3**；SWB 的 I2C 通道與位址已於 2026-08-19 上機驗證。
+最後一次發布是 **V1.1.5**；SWB 的 I2C 通道與位址已於 2026-08-19 上機驗證。
 margin 的 `VNOM` 已於 2026-08-30 改為 Blanton 實測中位數（144 條軌中 86 條上調 0.8~2.5%）。
 交付用 `./publish/publish.sh` 打包。
 
@@ -117,6 +117,23 @@ bash ~/Blanton_Script/port_prbs_monitor.sh report       # PASS/FAIL 統計（沒
 bash ~/Blanton_Script/port_prbs_monitor.sh stop         # 收尾會跑 prbsstat STOp + prbs clear
 #   ⚠️ PRBS 打起來時 link 會顯示 down，這是正常的 —— 所以 start 刻意不印 port status
 
+# ── PDB / CPB power brick 讀值 ──────────────────────
+./Blanton_Script/pwr_brick.sh show         # Vin/Iin/Vout/Iout/Temp × 5 顆
+./Blanton_Script/pwr_brick.sh show -r      # 多印 raw word
+#   四顆 ADPM12200 每個量各一個 PMBus PAGE：Vin 9 / Iin 10 / Vout 2 / Iout 14 / Temp 18
+#   CPB.PU37 (0x26) 是不同零件：不寫 PAGE，自己一套換算
+#   PB_TRIES=1 ... show -r  可看未經重試的原始行為
+
+# ── 多相 VRM margin（原生 i2c，38 條軌）──────────────
+./Blanton_Script/blanton_multiphase_margin.sh high3    # 全部 +3%
+./Blanton_Script/blanton_multiphase_margin.sh low3     # 全部 -3%
+./Blanton_Script/blanton_multiphase_margin.sh comboA   # 混合，組合 A
+./Blanton_Script/blanton_multiphase_margin.sh comboB   # 混合，組合 B
+./Blanton_Script/blanton_multiphase_margin.sh save     # ⚠️ 永久寫 NVM
+#   -u 0 / -u 1 單邊（SWB0=i2c-13/15，SWB1=i2c-14/16）；-n 只印指令
+#   逐條印 SWB0_0V9_ANLG0 - 0.930V Configure Done；save 只印 Multiphase Save All
+#   ⚠️ 這不是 margin.sh 管的 LTC2980，兩支摸同一批軌，不要同時用
+
 # ── 全機 SerDes BER（PRBS，期間 link 會顯示 DOWN）────
 ./Blanton_Script/blanton_ber.sh init          # prbs set p=3 + prbs get（檢查每條 lane 鎖定）
 ./Blanton_Script/blanton_ber.sh start         # prbsstat STArt Interval=30
@@ -222,6 +239,21 @@ Tera Term 連 COM port (115200-8-N-1)
 - ⚠️ **ICB/PDB 一律走 VI2C（`blanton_icb_vi2c.sh`），不要走 VSPI**：VSPI ~18 ms/reg 會讓 I2C
   byte 相間隔拉到 ~50 ms，踩中 SMBus 25–35 ms timeout，裝置直接 NACK。實測全掃 9.4 s vs 34.0 s。
 - ⚠️ **I2C 讀一律 Repeated START**（不是 STOP + START），否則 PMBus/SMBus 裝置（VRM、EFUSE）不理。
+- ⚠️ **Script C 的 BMC USB service log 不進 master log**：改成
+  `journalctl ... > log/bmc_usb_net.log` 再複製到隨身碟，**那是唯一一份**。
+  收工後翻不到就先確認 job 目錄裡有沒有這個檔
+- ⚠️ **VI2C 這條路的壞法是「只壞高位元組」**，不是整包壞掉。`11.98 V` 會變成 `32.00 V`
+  —— 正的、數量級也不誇張，**擋全一/全零的過濾完全攔不到**。寫任何 VI2C 讀值工具都要有
+  合理範圍檢查 + 重讀，光靠 `PDB_REJECT_FFFF` 那種是不夠的（`pwr_brick.sh` 的教訓）
+- ⚠️ **PMBus 的 PAGE 不是只有 VRM 通道在用**：ADPM12200 把每個量測放在不同 PAGE
+  （Vin 9 / Iin 10 / Vout 2 / Iout 14 / Temp 18），沒寫 PAGE 就讀，回的是 `0xFFFF` 或
+  `0x0000`。`blanton_pwr_data.sh` 的 PDB 表 page 是 `-`，這就是它整張表 NA 的原因
+- ⚠️ **`--runtime 86400` 是 24 小時上限**：超過一天的 soak，SSD / USB 壓力會安靜結束，
+  剩下的時間那兩項閒置。`bgctl list` 的數量變少是唯一的線索，**不會報警**
+- ⚠️ **多相 VRM 與 LTC2980 是同一批軌的兩條路**：`blanton_multiphase_margin.sh`（原生 i2c）
+  和 `margin.sh`（LTC2980 PMBus）都假設自己是唯一寫入者，**沒有互斥檢查**，只靠人記得
+- ⚠️ **traffic 的計數器基準在 v0.7.0 變了**：`tx 100 length=512` → `tx 200 length=324`，
+  每 burst 的位元組數 +27%。PASS/FAIL 是成對交叉比對不受影響，但**絕對值不能跟舊 log 比**
 - ⚠️ **Script 4（thermal/safety）沒有收尾**：`while 1` 之後就是檔尾。中斷後 DUT 停在
   `port cd lb=mac` / `l2 learn off` / `test mode nr=yes`，`mlucas-avx2` 也還在背景。
   下一個測試會在被污染的狀態上開始，而且 **`show interfaces status` 看不出來**。

docs/release-notes/v1.1.5.md

@@ -0,0 +1,67 @@
+# v1.1.5 — The stress jobs now last the whole soak
+
+## 🐛 Bug fixes
+
+**USB stress ran for sixty seconds of an overnight soak**
+* `qfx5252-stress-usb` was started with `--runtime 60`. It finished a minute in and the USB path sat idle for the rest of the night. Nothing failed, nothing said so, and the run looked complete.
+* SSD stress had the same shape at `--runtime 3600` — one hour of a soak that usually runs far longer.
+* Both are now `--runtime 86400`, and the BMC DDR memtester lost its loop count (`64M 1` → `64M`) so it runs until it is stopped rather than finishing one pass.
+* **86400 is 24 hours, not "forever".** A soak longer than a day leaves SSD and USB dead for the remainder. Script B prints `bgctl list` every round (since v1.0.10), so the shorter list is visible there — but nothing raises an alarm.
+
+## ✨ New features
+
+**Multiphase VRM margin**
+* New `blanton_multiphase_margin.sh` drives the multiphase controllers on both switch boards over the native i2c buses — SWB0 on `/dev/i2c-13` and `-15`, SWB1 on `-14` and `-16`. 19 rails per board, 38 in all.
+* `high3` / `low3` / `comboA` / `comboB` set the voltages and report one line per rail:
+
+  ```
+  SWB0_0V9_ANLG0 - 0.930V Configure Done
+  SWB0_0V75_ANLG0 - 0.775V Configure Done
+  ...
+  [ OK ] high3: 38 rail(s) configured
+  ```
+* `save` commits them. It has no per-rail mapping, so it reports as one operation: `Multiphase Save All`.
+* `-u 0` / `-u 1` for a single board; rails belonging to the other board are skipped and counted separately, not failed.
+* **`save` writes NVM permanently** (PMBus `STORE_USER_ALL`, and `0x17` on the TH6 core rail). A power cycle does not undo it.
+* **These are not the LTC2980s that `margin.sh` drives.** The two tools reach the same rails from different sides and each assumes it is the only writer. There is no interlock — do not run both.
+
+**Traffic bursts carry a random pattern**
+* `blanton_traffic_linespeed` v0.7.0 appends `PatternRandom=yes` to every `tx`, `ce0` included. A fixed pattern can sit on a benign bit sequence for an entire run; a changing one is what makes a weak lane show itself.
+* `-r no` forces the fixed pattern; `-r ""` leaves the argument off entirely, which is the pre-v0.7.0 wire format if a future SDK rejects it.
+* Defaults change from `tx 100 length=512` to `tx 200 length=324`.
+* **Counter totals are not comparable across this build**: 64800 bytes per burst instead of 51200, about 27% more. The PASS/FAIL cross-check compares a pair against each other and is unaffected — only absolute figures moved.
+
+## 📦 Downloads
+
+| File | Contents |
+|---|---|
+| `Script_ABC_Blanton_V1.1.5.zip` | The full Tera Term working directory, including `Blanton_Script/` to copy onto the DUT |
+
+**After copying to the DUT:**
+
+```bash
+chmod +x ~/Blanton_Script/*.sh      # see below
+grep -rlU $'\r' ~/Blanton_Script    # expect no output
+```
+
+`blanton_ber.sh`, `nfc_polling.sh`, `blanton_tr518.sh`, `blanton_multiphase_margin.sh` and the two `TH6_SWB*_power_readback.sh` are invoked through `./` or `~/`, so they need the execute bit along with `bmc_monitor.sh` and `usb_target.sh` — neither git nor a Windows/USB copy carries it reliably.
+
+## ⚠️ Before you run
+
+* **A soak longer than 24 hours needs the runtimes raised.** `--runtime 86400` is a ceiling; past it, SSD and USB are idle and only a shorter `bgctl list` hints at it.
+* **`blanton_multiphase_margin.sh save` is permanent.** Read the rails back before committing, and never run it during a test.
+* **Do not mix `blanton_multiphase_margin.sh` and `margin.sh`** — same rails, two different access paths, no interlock.
+* **Traffic counters changed scale.** Any absolute thresholds taken from earlier logs need redoing.
+* **Script 4 (thermal/safety) has no teardown** — finish with `blanton_tr518.sh stop` and `kill $(jobs -p)`.
+* **These three cannot share the switch**: `blanton_ber.sh`, `blanton_tr518.sh`, `blanton_traffic_linespeed`.
+* **Margin is only sampled at the start and end of a soak** (since v1.1.4), not during it.
+* **`FAN_SPEED` is 100** — the fans run flat out unless you change `config.ttl`.
+* **The three items listed as unverified in v1.1.0 are still unverified**: the `ce0` ingress mirror, the 120s settle in `blanton_tr518.sh`, and `test mode nr=no` on stop.
+
+## 🔗 Links
+
+* [Blanton_Test_Flow.drawio](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/docs/Blanton_Test_Flow.drawio) — the four scripts side by side
+* [ARCHITECTURE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/ARCHITECTURE.md) — test flow, data models, constraints
+* [CLAUDE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/CLAUDE.md) — commands and the bench gotchas
+
+**Full changelog:** [V1.1.4...V1.1.5](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/compare/V1.1.4...V1.1.5)

docs/release-notes/v1.1.6.md

@@ -0,0 +1,74 @@
+# v1.1.6 — The PDB bricks were never being asked the right question
+
+## 🐛 Bug fixes
+
+**Every PDB reading was `NA`, and the cause was a page number written in the wrong base**
+* The four ADPM12200 bricks put each measurement on its own PMBus PAGE, and the page has to be written before every read. The bring-up spreadsheet listed those page numbers in decimal but with an `0x` prefix, so four of the five selected the wrong page:
+
+  | Reading | Datasheet PAGE | Should send | Spreadsheet said |
+  |---|---|---|---|
+  | Vin | 9 | `0x09` | `0x00` |
+  | Iin | 10 | `0x0A` | `0x10` |
+  | Vout | 2 | `0x02` | `0x02` ✅ |
+  | Iout | 14 | `0x0E` | `0x14` |
+  | Temp | 18 | `0x12` | `0x18` |
+
+* Only Vout worked — because 2 reads the same in either base. That is why Iin and Iout answered `0xFFFF` and the temperature answered `0x0000`, and why a Vin scaling had to be invented to make 50 V appear.
+* `blanton_pwr_data.sh` sends no page at all (its PDB table has `page "-"`), which is the reason it reports the whole PDB section as `NA`.
+
+## ✨ New features
+
+**`pwr_brick.sh` — the five power bricks, read properly**
+* `show` prints Vin / Iin / Vout / Iout / Temp for all five: `SWB0.PU207` (0x62), `SWB0.PU13` (0x63), `SWB1.PU332` (0x60), `SWB1.PU85` (0x61) and `CPB.PU37` (0x26). `-r` adds the raw words.
+* Conversions come from the datasheet's DIRECT equation, `X = (1/m)(Y × 10⁻ᴿ − b)`, with Table 3's coefficients: voltage `Y × 8 mV`, current `Y × 0.04 A`, temperature `Y × 0.01 °C`.
+* **Cross-checked, not assumed**: `READ_VOUT` returns `0x05D4` → 1492 × 8 = 11936 mV, which is exactly the figure `show platform voltage` reports for that rail from a completely separate sensor path.
+* `CPB.PU37` is a different part — no page writes and its own scaling — and is handled separately.
+* The datasheet is now in the repo (`docs/ADPM12200CMLZxx_DS_*.pdf`) so the pages and coefficients can be checked without hunting for it.
+
+**Every value is validated before it is printed**
+* This bus corrupts the **high byte only**. That turns `11.98 V` into `32.00 V` — positive, plausible in magnitude, and invisible to any "reject 0xFFFF" filter. Each value is re-read (up to `PB_TRIES`, default 8) until it is not `0xFFFF`, not `0x0000`, and lands inside a plausibility window.
+* `0x0000` is rejected as a raw word for the same reason: on the temperature register it decodes to a perfectly believable 0 °C.
+
+**Complementary margin profiles per board**
+* `comboA` / `comboB` for CB and each SWB CONN. `comboB` is `comboA` with every direction flipped, so running both covers each rail high and low while its neighbours sit the other way.
+* NC channels stay at `nominal` in both — there is nothing to margin on an unused rail (CONN14 CH10/11/13, CONN15 CH10).
+
+**The BMC USB service log is captured again — to a file**
+* Script C's `journalctl` dump had been commented out, so that service log reached nothing at all. It now runs with `-o short-iso` into `log/bmc_usb_net.log` and is copied into the job directory for the USB archive. The ISO timestamps line up with the other monitor logs, and `rm -f` first keeps the file to one run.
+* **It is no longer printed to the console**, so the USB copy is the only copy. If that `cp` fails — and nothing checks it — the service log is gone. Check the job directory before packing up.
+
+## 📦 Downloads
+
+| File | Contents |
+|---|---|
+| `Script_ABC_Blanton_V1.1.6.zip` | The full Tera Term working directory, including `Blanton_Script/` to copy onto the DUT |
+
+**After copying to the DUT:**
+
+```bash
+chmod +x ~/Blanton_Script/*.sh      # see below
+grep -rlU $'\r' ~/Blanton_Script    # expect no output
+```
+
+`blanton_ber.sh`, `nfc_polling.sh`, `blanton_tr518.sh`, `blanton_multiphase_margin.sh`, `pwr_brick.sh` and the two `TH6_SWB*_power_readback.sh` are invoked through `./` or `~/`, so they need the execute bit along with `bmc_monitor.sh` and `usb_target.sh` — neither git nor a Windows/USB copy carries it reliably.
+
+## ⚠️ Before you run
+
+* **`READ_VIN` and `READ_IIN` are not in the datasheet's coefficient table.** They are decoded here with the voltage and current coefficients — consistent with a ~50 V input, but not stated by the datasheet. Anything quoting brick Vin should have that confirmed first. `PB_VIN_M` / `PB_IIN_M` are where to change it.
+* **The BMC USB service log only exists on the USB stick.** It is not in the master console log any more.
+* **`NA` has two meanings**: nothing readable, or read but outside its plausibility window. Use `PB_TRIES=1 ./Blanton_Script/pwr_brick.sh show -r` to see the unretried raw words and tell them apart.
+* **Margin profiles are positional.** `comboA_SWB_CONN13` applied to a CONN16 board margins the wrong rails and nothing detects it.
+* **`blanton_multiphase_margin.sh save` is permanent**, and it must not be mixed with `margin.sh` — same rails, two access paths, no interlock.
+* **A soak longer than 24 hours needs the stress runtimes raised** — `--runtime 86400` is a ceiling.
+* **Script 4 (thermal/safety) has no teardown** — finish with `blanton_tr518.sh stop` and `kill $(jobs -p)`.
+* **These three cannot share the switch**: `blanton_ber.sh`, `blanton_tr518.sh`, `blanton_traffic_linespeed`.
+* **`FAN_SPEED` is 100.**
+* **The three items listed as unverified in v1.1.0 are still unverified**: the `ce0` ingress mirror, the 120s settle in `blanton_tr518.sh`, and `test mode nr=no` on stop.
+
+## 🔗 Links
+
+* [ARCHITECTURE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/ARCHITECTURE.md) — test flow, data models, constraints
+* [CLAUDE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/CLAUDE.md) — commands and the bench gotchas
+* [Blanton_Test_Flow.drawio](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/docs/Blanton_Test_Flow.drawio) — the four scripts side by side
+
+**Full changelog:** [V1.1.5...V1.1.6](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/compare/V1.1.5...V1.1.6)

src/Script_ABC_Blanton/1_Blanton_Script_A.ttl

@@ -1,7 +1,7 @@
 ; =============================================================================
 ; Script A for Blanton
-; Version : V1.1.4
+; Version : V1.1.7
-; Date    : 2026-08-31
+; Date    : 2026-09-04
 ; Author  : ETWen
 ; =============================================================================
 ; Version History:
@@ -201,6 +201,94 @@
 ;                                                                         finish - leaves the session shell first, so finish
 ;                                                                         runs in the login shell that opened it
 ;                       docs/Blanton_Test_Flow.drawio                   Add the A/B/C + thermal flow diagram
+;   V1.1.5  2026-09-01  ScriptB                                         Stress jobs now last the whole soak
+;                                                                         BMC DDR   memtester 64M 1 -> 64M   (loop count
+;                                                                                   dropped = runs until stopped)
+;                                                                         SSD       --runtime 3600  -> 86400
+;                                                                         USB       --runtime 60    -> 86400
+;                                                                         The USB one finished after 60 SECONDS, so an
+;                                                                         overnight run had USB idle for all but the first
+;                                                                         minute and nothing said so
+;                                                                         !! 86400 is 24h: a soak longer than that leaves SSD
+;                                                                            and USB dead for the remainder - the per-round
+;                                                                            bgctl list (V1.0.10) is where that shows up
+;                       Blanton_Script/blanton_multiphase_margin.sh     Add multiphase VRM margin over the native i2c buses
+;                                                                         high3 / low3 / comboA / comboB / save, -u 0|1|all
+;                                                                         38 rails (19 per SWB), one line each:
+;                                                                           SWB0_0V9_ANLG0 - 0.930V Configure Done
+;                                                                         save has no per-rail map, prints Multiphase Save All
+;                                                                         !! save is STORE_USER_ALL - permanent, survives a
+;                                                                            power cycle
+;                                                                         !! these are NOT the LTC2980s margin.sh drives; the
+;                                                                            two tools reach the same rails from different
+;                                                                            sides - do not run both
+;                       Blanton_Script/blanton_traffic_linespeed.sh     v0.7.0  tx gains PatternRandom, defaults change
+;                                                                         tx 100 length=512 -> tx 200 length=324
+;                                                                         every burst now ends PatternRandom=yes, ce0 included
+;                                                                         A fixed pattern can sit on a benign bit sequence for
+;                                                                         a whole run; random is what exposes a weak lane
+;                                                                         -r no forces the fixed pattern, -r "" omits the
+;                                                                         argument entirely (pre-v0.7.0 wire format)
+;                                                                         !! bytes per burst went 51200 -> 64800 (+27%), so
+;                                                                            counter totals are not comparable across this
+;                                                                            build - the PASS/FAIL cross-check is unaffected
+;                       tools/Multiphase_*.txt                          Bench command references for the new script
+;   V1.1.6  2026-09-02  Blanton_Script/pwr_brick.sh                     Add PDB / CPB power brick readings
+;                                                                         5 devices, Vin / Iin / Vout / Iout / Temp:
+;                                                                           SWB0.PU207 0x62  SWB0.PU13  0x63
+;                                                                           SWB1.PU332 0x60  SWB1.PU85  0x61
+;                                                                           CPB.PU37   0x26
+;                                                                         The four ADPM12200 put each measurement on its own
+;                                                                         PMBus PAGE, so a PAGE write has to precede every
+;                                                                         read - blanton_pwr_data.sh sends none, which is why
+;                                                                         it reports the whole PDB table as NA
+;                                                                           Vin  PAGE 9   Iin PAGE 10  Vout PAGE 2
+;                                                                           Iout PAGE 14  Temp PAGE 18
+;                                                                         !! the bring-up spreadsheet wrote those page numbers
+;                                                                            in decimal but with an 0x prefix (10 -> 0x10,
+;                                                                            14 -> 0x14, 18 -> 0x18). Only Vout worked,
+;                                                                            because 2 reads the same either way
+;                                                                         Conversions are the datasheet DIRECT equation
+;                                                                         X = (1/m)(Y x 10^-R - b), Table 3: voltage Y x 8mV,
+;                                                                         current Y x 0.04A, temperature Y x 0.01C
+;                                                                         Checked: READ_VOUT 0x05D4 -> 11936 mV, the same
+;                                                                         figure show platform reports for that rail
+;                                                                         !! Table 3 does NOT list READ_VIN / READ_IIN; they
+;                                                                            borrow the voltage / current coefficients here
+;                                                                         Each value is re-read until it passes: not 0xFFFF,
+;                                                                         not 0x0000, and inside a plausibility window. This
+;                                                                         bus corrupts the HIGH BYTE only, which turns 11.98 V
+;                                                                         into 32.00 V - a value no all-ones filter catches
+;                       docs/ADPM12200..._Datasheet_2025_12_19.pdf      The brick datasheet the pages and coefficients above
+;                                                                         came from
+;                       ScriptC                                         Re-enable the BMC USB service log, and send it to
+;                                                                         a file instead of the console
+;                                                                         journalctl ... -o short-iso > log/bmc_usb_net.log
+;                                                                         then cp it into the job dir for the USB archive
+;                                                                         rm -f first, so the file is this run only
+;                                                                         -o short-iso gives it timestamps that line up with
+;                                                                         the other monitor logs
+;                                                                         !! it no longer appears in the master console log,
+;                                                                            so the USB copy is now the ONLY copy - if that
+;                                                                            cp fails the service log is gone
+;                       LTC2980_Margin_Script/profiles/                 Add comboA / comboB per board (CB + SWB CONN13..16)
+;                                                                         Checkerboard pair: comboB is comboA with every
+;                                                                         direction flipped, so running both covers each rail
+;                                                                         high and low while its neighbours sit the other way
+;                                                                         NC channels stay nominal in both (CONN14 CH10/11/13,
+;                                                                         CONN15 CH10) - nothing to margin on an unused rail
+;   V1.1.7  2026-09-04  Blanton_Script/blanton_multiphase_margin.sh     v1.1.0  Add the 'normal' sub-command
+;                                                                         Puts all 38 rails back to their nominal set point,
+;                                                                         from tools/Multiphase_Normal.txt - same rails and the
+;                                                                         same per-rail reporting as the margin profiles
+;                                                                         Until now the only way back from a margin was a power
+;                                                                         cycle, and 'save' run while margined would have
+;                                                                         committed the offsets to NVM, where a power cycle does
+;                                                                         not help either
+;                                                                         !! TH6_CORE is 0.8 V nominal but settles near 0.8591 V
+;                                                                            once the load line is active - reading back 0.859
+;                                                                            after 'normal' is the load line, not a failed write
+;                       tools/Multiphase_Normal.txt                     Bench command reference for the above
 ; =============================================================================
 include "config.ttl"
 

src/Script_ABC_Blanton/2_Blanton_Script_B.ttl

@@ -26,7 +26,8 @@ sendln "~/hammer/tools/amd/mlucas-avx2 -s l -cpu 0:15 > ~/hammer/tools/amd/mluca
 ;wait prompt_sonic_root
 ;sendln "./Blanton_Script/bmc_monitor.sh start"
 wait prompt_sonic_root
-sendln "bgctl run bmc-manager run '/usr/bin/memtester 64M 1'"
+;sendln "bgctl run bmc-manager run '/usr/bin/memtester 64M 1'"
+sendln "bgctl run bmc-manager run '/usr/bin/memtester 64M'"     ; Continue Execture
 
 ; ========== BMC Monitor Test ==========
 wait prompt_sonic_root
@@ -40,7 +41,7 @@ sendln "bgctl run /usr/sbin/memtester 1G"   ; Continue Execture
 
 ; ========== SSD read/write ==========
 wait prompt_sonic_root
-sendln "bgctl run qfx5252-stress-ssd 1G --runtime 3600 --passes 5 --write --force --log /host/hw-eval/jobs/qfx5252-stress-ssd.log"
+sendln "bgctl run qfx5252-stress-ssd 1G --runtime 86400 --passes 5 --write --force --log /host/hw-eval/jobs/qfx5252-stress-ssd.log"
 
 ; ========== USB read/write ==========
 ; ---- Get USB partition node -> usb_dev ----
@@ -51,7 +52,7 @@ waitregex '<<DEV=([^>]*)>>'
 usb_dev = groupmatchstr1
 
 wait prompt_sonic_root
-sprintf2 cmd "bgctl run qfx5252-stress-usb %s 256M --runtime 60 --passes 1 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log" usb_dev
+sprintf2 cmd "bgctl run qfx5252-stress-usb %s 256M --runtime 86400 --passes 1 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log" usb_dev
 sendln cmd
 
 ;wait prompt_sonic_root

src/Script_ABC_Blanton/3_Blanton_Script_C.ttl

@@ -78,8 +78,10 @@ wait prompt_sonic_root
 sendln "cat ./Blanton_Script/log/bmc_poll.log"
 
 ; ========== BMC USB Test result ==========
-;wait prompt_sonic_root
+wait prompt_sonic_root
-;sendln "journalctl -u qfx5252-bmc-usb-net-test.service --no-pager"
+sendln "rm -f ~/Blanton_Script/log/bmc_usb_net.log"
+wait prompt_sonic_root
+sendln "journalctl -u qfx5252-bmc-usb-net-test.service --no-pager -o short-iso > ~/Blanton_Script/log/bmc_usb_net.log"
 
 
 ; ========== CHECK Stress results ==========
@@ -209,12 +211,16 @@ sendln cmd
 
 ; ========== Copy Stress Log to USB ==========
 wait prompt_sonic_root
+sendln "cp ./Blanton_Script/log/bmc_usb_net.log /host/hw-eval/jobs/"
+wait prompt_sonic_root
 sendln "cp ./Blanton_Script/log/bmc_poll.log /host/hw-eval/jobs/"
 wait prompt_sonic_root
 sendln "cp ./Blanton_Script/log/mgmt_ping.log /host/hw-eval/jobs/"
 wait prompt_sonic_root
 sendln "cp ./Blanton_Script/log/nfc_poll.log /host/hw-eval/jobs/"
 
+
+
 wait prompt_sonic_root
 getdate ts_date "%Y%m%d"
 gettime ts_time "%H%M"

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboA_CB.conf

@@ -0,0 +1,26 @@
+# Profile: comboA_CB - checkerboard, the complement of comboB_CB
+# Board: CB only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboA then comboB to cover every rail in both directions while its
+# neighbours sit the other way.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:low:5"
+    "1:low:5"
+    "2:high:5"
+    "3:low:5"
+    "4:high:5"
+    "5:high:5"
+    "6:high:5"
+    "7:high:5"
+    "8:low:5"
+    "9:high:5"
+    "10:high:5"
+    "11:high:5"
+    "12:low:5"
+    "13:high:5"
+    "14:high:5"
+    "15:low:5"
+)

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboA_SWB_CONN13.conf

@@ -0,0 +1,26 @@
+# Profile: comboA_SWB_CONN13 - checkerboard, the complement of comboB_SWB_CONN13
+# Board: SWB_CONN13 only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboA then comboB to cover every rail in both directions while its
+# neighbours sit the other way.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:high:3"
+    "1:high:3"
+    "2:low:3"
+    "3:low:3"
+    "4:high:5"
+    "5:low:5"
+    "6:high:5"
+    "7:high:5"
+    "8:high:5"
+    "9:high:3"
+    "10:high:3"
+    "11:low:3"
+    "12:low:3"
+    "13:high:3"
+    "14:high:3"
+    "15:low:5"
+)

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboA_SWB_CONN14.conf

@@ -0,0 +1,28 @@
+# Profile: comboA_SWB_CONN14 - checkerboard, the complement of comboB_SWB_CONN14
+# Board: SWB_CONN14 only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboA then comboB to cover every rail in both directions while its
+# neighbours sit the other way.
+# CH 10, 11, 13 stay nominal: they are NC on this board, so there is
+# nothing to margin.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:high:3"
+    "1:low:3"
+    "2:low:3"
+    "3:high:5"
+    "4:high:5"
+    "5:high:5"
+    "6:low:5"
+    "7:low:5"
+    "8:low:3"
+    "9:low:3"
+    "10:nominal:5"
+    "11:nominal:5"
+    "12:high:3"
+    "13:nominal:5"
+    "14:high:5"
+    "15:high:3"
+)

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboA_SWB_CONN15.conf

@@ -0,0 +1,28 @@
+# Profile: comboA_SWB_CONN15 - checkerboard, the complement of comboB_SWB_CONN15
+# Board: SWB_CONN15 only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboA then comboB to cover every rail in both directions while its
+# neighbours sit the other way.
+# CH 10 stay nominal: they are NC on this board, so there is
+# nothing to margin.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:low:3"
+    "1:low:3"
+    "2:high:3"
+    "3:high:3"
+    "4:low:3"
+    "5:low:3"
+    "6:high:5"
+    "7:high:3"
+    "8:high:5"
+    "9:low:5"
+    "10:nominal:5"
+    "11:low:5"
+    "12:low:3"
+    "13:high:3"
+    "14:high:3"
+    "15:high:5"
+)

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboA_SWB_CONN16.conf

@@ -0,0 +1,26 @@
+# Profile: comboA_SWB_CONN16 - checkerboard, the complement of comboB_SWB_CONN16
+# Board: SWB_CONN16 only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboA then comboB to cover every rail in both directions while its
+# neighbours sit the other way.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:high:3"
+    "1:high:5"
+    "2:high:5"
+    "3:low:5"
+    "4:high:5"
+    "5:low:5"
+    "6:high:5"
+    "7:high:3"
+    "8:high:3"
+    "9:high:3"
+    "10:low:3"
+    "11:low:3"
+    "12:low:3"
+    "13:low:3"
+    "14:low:3"
+    "15:high:3"
+)

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboB_CB.conf

@@ -0,0 +1,26 @@
+# Profile: comboB_CB - checkerboard, the complement of comboA_CB
+# Board: CB only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboB then comboA to cover every rail in both directions while its
+# neighbours sit the other way.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:high:5"
+    "1:high:5"
+    "2:low:5"
+    "3:high:5"
+    "4:low:5"
+    "5:low:5"
+    "6:low:5"
+    "7:low:5"
+    "8:high:5"
+    "9:low:5"
+    "10:low:5"
+    "11:low:5"
+    "12:high:5"
+    "13:low:5"
+    "14:low:5"
+    "15:high:5"
+)

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboB_SWB_CONN13.conf

@@ -0,0 +1,26 @@
+# Profile: comboB_SWB_CONN13 - checkerboard, the complement of comboA_SWB_CONN13
+# Board: SWB_CONN13 only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboB then comboA to cover every rail in both directions while its
+# neighbours sit the other way.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:low:3"
+    "1:low:3"
+    "2:high:3"
+    "3:high:3"
+    "4:low:5"
+    "5:high:5"
+    "6:low:5"
+    "7:low:5"
+    "8:low:5"
+    "9:low:3"
+    "10:low:3"
+    "11:high:3"
+    "12:high:3"
+    "13:low:3"
+    "14:low:3"
+    "15:high:5"
+)

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboB_SWB_CONN14.conf

@@ -0,0 +1,28 @@
+# Profile: comboB_SWB_CONN14 - checkerboard, the complement of comboA_SWB_CONN14
+# Board: SWB_CONN14 only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboB then comboA to cover every rail in both directions while its
+# neighbours sit the other way.
+# CH 10, 11, 13 stay nominal: they are NC on this board, so there is
+# nothing to margin.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:low:3"
+    "1:high:3"
+    "2:high:3"
+    "3:low:5"
+    "4:low:5"
+    "5:low:5"
+    "6:high:5"
+    "7:high:5"
+    "8:high:3"
+    "9:high:3"
+    "10:nominal:5"
+    "11:nominal:5"
+    "12:low:3"
+    "13:nominal:5"
+    "14:low:5"
+    "15:low:3"
+)

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboB_SWB_CONN15.conf

@@ -0,0 +1,28 @@
+# Profile: comboB_SWB_CONN15 - checkerboard, the complement of comboA_SWB_CONN15
+# Board: SWB_CONN15 only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboB then comboA to cover every rail in both directions while its
+# neighbours sit the other way.
+# CH 10 stay nominal: they are NC on this board, so there is
+# nothing to margin.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:high:3"
+    "1:high:3"
+    "2:low:3"
+    "3:low:3"
+    "4:high:3"
+    "5:high:3"
+    "6:low:5"
+    "7:low:3"
+    "8:low:5"
+    "9:high:5"
+    "10:nominal:5"
+    "11:high:5"
+    "12:high:3"
+    "13:low:3"
+    "14:low:3"
+    "15:low:5"
+)

src/Script_ABC_Blanton/Blanton_Script/LTC2980_Margin_Script/profiles/comboB_SWB_CONN16.conf

@@ -0,0 +1,26 @@
+# Profile: comboB_SWB_CONN16 - checkerboard, the complement of comboA_SWB_CONN16
+# Board: SWB_CONN16 only. The channel list is positional, so applying this to a
+# different board margins the wrong rails and nothing detects it.
+# Run comboB then comboA to cover every rail in both directions while its
+# neighbours sit the other way.
+# Applied to whichever LTC2980 is currently loaded via margin_init
+# Format: "channel:operation:change_percent"
+
+PROFILE_CHANNELS=(
+    "0:low:3"
+    "1:low:5"
+    "2:low:5"
+    "3:high:5"
+    "4:low:5"
+    "5:high:5"
+    "6:low:5"
+    "7:low:3"
+    "8:low:3"
+    "9:low:3"
+    "10:high:3"
+    "11:high:3"
+    "12:high:3"
+    "13:high:3"
+    "14:high:3"
+    "15:low:3"
+)

src/Script_ABC_Blanton/Blanton_Script/blanton_traffic_linespeed.sh

@@ -6,7 +6,7 @@
 #   V0.1.0  2026-08-17  First version. Bash port of the three Tera Term macros
 #                       utils/traffic_loopback_vlan_setting.ttl (VLAN 30..137,
 #                       port pair cdN <-> cdN+32), utils/traffic_loopback_start.ttl
-#                       (tx 100 length=512 VLantag=<vid>) and
+#                       (tx <count> length=<len> VLantag=<vid>) and
 #                       utils/traffic_loopback_vlan_remove.ttl.
 #                       One DUT = two switch boards -> bcmcmd unit 0 and 1
 #                       (bcmcmd -n <unit>), default both.
@@ -90,6 +90,16 @@
 #                       With only one unit selected the summary reports
 #                       UNDECIDED (exit 3) instead of guessing.
 #                       TL_CE_ENABLE=0 restores the old cd-pairs-only behaviour.
+#   V0.7.0  2026-09-01  Change: tx bursts carry PatternRandom=yes and the defaults
+#                       become tx 200 length=324 (were 100 / 512).
+#                       Random payload keeps the bit pattern changing instead of
+#                       repeating, which is what makes a marginal lane show up;
+#                       a fixed pattern can sit on a benign sequence all run.
+#                       TL_TX_RANDOM=no forces the fixed pattern, "" leaves the
+#                       argument off entirely (pre-V0.7.0 wire format).
+#                       NOTE: counters scale with count x length, so totals from
+#                       before this build are not comparable - 200x324 moves
+#                       about 27% more bytes per burst than 100x512.
 #   V0.6.0  2026-08-28  Add: ce0 traffic is now SUSTAINED, not a single burst.
 #                       A cd pair keeps its packets circulating because they
 #                       flood to the partner port; ce0 has no partner and a
@@ -142,6 +152,8 @@
 #                             aliases: -tx | --tx
 #   -l|--length <n>           tx packet length     (default $TL_TX_LENGTH)
 #                             aliases: -length | --len
+#   -r|--random <yes|no>      tx PatternRandom     (default $TL_TX_RANDOM;
+#                             empty string omits the argument)
 #   -p|--ports  <list|all>    ps: port list ('all' = plain 'ps', every port)
 #   -T|--tolerance <n>        report: allowed |delta| in packets (default 0;
 #                             -T 1 absorbs the normal snapshot skew)
@@ -161,7 +173,8 @@
 #   -h|--help                 help
 #
 # Environment overrides:
-#   BCMCMD_CMD=bcmcmd   TL_UNITS="0 1"   TL_TX_COUNT=100   TL_TX_LENGTH=512
+#   BCMCMD_CMD=bcmcmd   TL_UNITS="0 1"   TL_TX_COUNT=200   TL_TX_LENGTH=324
+#   TL_TX_RANDOM=yes
 #   TL_PS_PORTS="1-24,40-96,..."         TL_TOLERANCE=0    TL_LOG_DIR=/tmp
 #   DEBUG_MODE=1
 #
@@ -173,8 +186,14 @@
 # === Config ==================================================================
 BCMCMD_CMD="${BCMCMD_CMD:-bcmcmd}"
 TL_UNITS="${TL_UNITS:-0 1}"          # one DUT = two switch boards (0 and 1)
-TL_TX_COUNT="${TL_TX_COUNT:-100}"
+TL_TX_COUNT="${TL_TX_COUNT:-200}"
-TL_TX_LENGTH="${TL_TX_LENGTH:-512}"
+TL_TX_LENGTH="${TL_TX_LENGTH:-324}"
+
+# PatternRandom=yes|no is appended to every tx burst. Random payload exercises
+# the SerDes with changing bit patterns instead of the repeating one a fixed
+# pattern produces, which is what makes a marginal lane show up.
+# Set to "" to leave the argument off entirely (pre-V0.7.0 behaviour).
+TL_TX_RANDOM="${TL_TX_RANDOM:-yes}"
 TL_DEFAULT_VLAN="${TL_DEFAULT_VLAN:-1}"
 TL_DEFAULT_VLAN_PBM="${TL_DEFAULT_VLAN_PBM:-cd}"
 
@@ -515,17 +534,23 @@ traffic_linespeed_start() {
     _tl_units_check || return 1
     _tl_is_uint "$TL_TX_COUNT"  || { _tl_err "tx count '$TL_TX_COUNT' is not a positive integer (-tx|-c <n>)"; return 1; }
     _tl_is_uint "$TL_TX_LENGTH" || { _tl_err "tx length '$TL_TX_LENGTH' is not a positive integer (-length|-l <n>)"; return 1; }
+    local rnd=""
+    case "$TL_TX_RANDOM" in
+        yes|no) rnd=" PatternRandom=$TL_TX_RANDOM" ;;
+        "")     rnd="" ;;
+        *)      _tl_err "PatternRandom '$TL_TX_RANDOM' must be yes, no or empty (-r|--random)"; return 1 ;;
+    esac
     local unit vid pa pb n fail
     for unit in $TL_UNITS; do
         n=0; fail=0
-        _tl_info "unit $unit: tx $TL_TX_COUNT length=$TL_TX_LENGTH per VLAN 30..137"
+        _tl_info "unit $unit: tx $TL_TX_COUNT length=$TL_TX_LENGTH${rnd} per VLAN 30..137"
         while read -r vid pa pb <&3; do
             [ -z "$vid" ] && continue
-            _tl_bcm_q "$unit" "tx $TL_TX_COUNT length=$TL_TX_LENGTH VLantag=$vid" || fail=$((fail+1))
+            _tl_bcm_q "$unit" "tx $TL_TX_COUNT length=$TL_TX_LENGTH VLantag=$vid${rnd}" || fail=$((fail+1))
             n=$((n+1))
         done 3<<< "$TL_PAIRS"
         if [ "$TL_CE_ENABLE" = "1" ]; then
-            _tl_bcm_q "$unit" "tx $TL_TX_COUNT length=$TL_TX_LENGTH VLantag=$TL_CE_VLAN" || fail=$((fail+1))
+            _tl_bcm_q "$unit" "tx $TL_TX_COUNT length=$TL_TX_LENGTH VLantag=$TL_CE_VLAN${rnd}" || fail=$((fail+1))
             n=$((n+1))
         fi
         if [ "$fail" -eq 0 ]; then
@@ -949,7 +974,7 @@ traffic_linespeed_run() {
 blanton_traffic_linespeed_help() {
     echo -e "\033[1mblanton_traffic_linespeed.sh - SWB loopback line-speed traffic (bcmcmd)\033[0m"
     echo ""
-    echo -e "  Units: \033[36m$TL_UNITS\033[0m   tx: \033[36m$TL_TX_COUNT pkt x ${TL_TX_LENGTH}B\033[0m"
+    echo -e "  Units: \033[36m$TL_UNITS\033[0m   tx: \033[36m$TL_TX_COUNT pkt x ${TL_TX_LENGTH}B\033[0m   PatternRandom: \033[36m${TL_TX_RANDOM:-（不加）}\033[0m"
     echo -e "  VLANs: 30..137 ($(_tl_pair_count) loopback pairs, cdN <-> cdN+32)"
     [ "$TL_CE_ENABLE" = "1" ] && \
         echo -e "  100G : VLAN \033[36m$TL_CE_VLAN\033[0m port \033[36m$TL_CE_PORT\033[0m  mode=\033[36m$TL_CE_MODE\033[0m (cross = unit0.$TL_CE_PORT <-> unit1.$TL_CE_PORT cabled)"
@@ -958,7 +983,7 @@ blanton_traffic_linespeed_help() {
     echo -e "  \033[33minit\033[0m     step 1  vlan remove 1 pbm=cd, vlan create/add each pair"
     echo -e "  \033[33mclear\033[0m    step 2  clear c"
     echo -e "  \033[33mshow\033[0m     step 3/6  show c  (run before and after traffic)"
-    echo -e "  \033[33mstart\033[0m    step 4  tx <count> length=<len> VLantag=<vid> per VLAN"
+    echo -e "  \033[33mstart\033[0m    step 4  tx <count> length=<len> VLantag=<vid> [PatternRandom=<yes|no>] per VLAN"
     echo -e "  \033[33mstop\033[0m     step 5  vlan remove <vid> pbm=<pair>  [--destroy also destroys]"
     [ "$TL_CE_ENABLE" = "1" ] && [ "$TL_CE_MIRROR" = "1" ] && \
         echo -e "           \033[33m^ also turns the $TL_CE_PORT mirror off -- without it the 100G loop keeps running\033[0m"
@@ -972,6 +997,7 @@ blanton_traffic_linespeed_help() {
     echo -e "  \033[33m-u|--unit\033[0m <0|1|all>   bcmcmd unit(s); 'all' = 0 1  (default: $TL_UNITS)"
     echo -e "  \033[33m-c|--count|-tx\033[0m <n>    tx packet count   (default $TL_TX_COUNT)"
     echo -e "  \033[33m-l|--length|-length\033[0m <n> tx packet length (default $TL_TX_LENGTH)"
+    echo -e "  \033[33m-r|--random\033[0m <yes|no>  tx PatternRandom (default $TL_TX_RANDOM; \"\" 完全不加)"
     echo -e "  \033[33m-p|--ports\033[0m <list>     ps port list, or 'all' for every port"
     echo -e "  \033[33m-T|--tolerance\033[0m <n>    report: allowed |delta| pkts (default $TL_TOLERANCE; -T 1 = snapshot skew)"
     echo -e "  \033[33m-a|--all\033[0m              report: kept for compatibility (all pairs are listed)"
@@ -995,7 +1021,8 @@ blanton_traffic_linespeed_help() {
     echo -e "  blanton_traffic_linespeed report -u 1 -q | grep -v PASS"
     echo -e "  blanton_traffic_linespeed report -f /tmp/showc_unit1_*.log -a"
     echo -e "  blanton_traffic_linespeed show -u 1 | grep -iE 'error|discard|drop'"
-    echo -e "  blanton_traffic_linespeed start -u 0 -tx 100 -length 512"
+    echo -e "  blanton_traffic_linespeed start -u 0 -tx 200 -length 324"
+    echo -e "  blanton_traffic_linespeed start -r no          # 固定樣式，不隨機"
     echo -e "  blanton_traffic_linespeed start -tx 100000 -length 9216 -d"
     echo -e "  blanton_traffic_linespeed stop --destroy"
     echo ""
@@ -1019,6 +1046,7 @@ blanton_traffic_linespeed() {
                 shift 2 ;;
             -c|--count|-tx|--tx)     TL_TX_COUNT="$2";  shift 2 ;;
             -l|-length|--length|--len) TL_TX_LENGTH="$2"; shift 2 ;;
+            -r|--random|-PatternRandom|--pattern-random) TL_TX_RANDOM="$2"; shift 2 ;;
             -p|--ports)   TL_PS_PORTS="$2";  shift 2 ;;
             -T|--tolerance) TL_TOLERANCE="$2"; shift 2 ;;
             -f|--file)    TL_REPORT_FILE="$2"; shift 2 ;;

src/Script_ABC_Blanton/Blanton_Script/pwr_brick.sh

@@ -0,0 +1,241 @@
+#!/usr/bin/env bash
+# =============================================================================
+# pwr_brick.sh  --  PDB / CPB power brick Vin / Iin / Vout / Iout / Temp
+# =============================================================================
+# Version History:
+#   V1.1.0  2026-09-02  PAGE values and conversions taken from the ADPM12200
+#                       datasheet instead of the bring-up spreadsheet.
+#                       The spreadsheet wrote every PAGE in decimal but with an
+#                       0x prefix, so four of the five selected the wrong page:
+#                           Vin  PAGE 9  -> it said 0x00   (should be 0x09)
+#                           Iin  PAGE 10 -> it said 0x10   (should be 0x0A)
+#                           Vout PAGE 2  -> it said 0x02    correct by luck
+#                           Iout PAGE 14 -> it said 0x14   (should be 0x0E)
+#                           Temp PAGE 18 -> it said 0x18   (should be 0x12)
+#                       Only Vout worked, because 2 reads the same either way.
+#                       That is why Iin/Iout answered 0xFFFF and Temp 0x0000.
+#                       Conversions now use the datasheet DIRECT equation; the
+#                       reverse-engineered BRICK_VIN_LSB is gone.
+#   V1.0.0  2026-09-02  First version.
+# =============================================================================
+#
+# Path:  CB FPGA F3 VI2C ch4  ->  TCA954x mux 0x72 ch0  ->  the bricks
+#
+# The four ADPM12200 modules put each measurement on its own PMBus PAGE, so a
+# PAGE write has to precede every read. blanton_pwr_data.sh does not send one
+# at all (its PDB table has page "-"), which is why it reports them as NA.
+#
+#   READ_VIN            0x88   PAGE 9
+#   READ_IIN            0x89   PAGE 10
+#   READ_VOUT           0x8B   PAGE 2
+#   READ_IOUT           0x8C   PAGE 14
+#   READ_TEMPERATURE_1  0x8D   PAGE 18
+#
+# DIRECT format, datasheet Table 3 ("PMBus Command Code Coefficients"):
+#
+#   X = (1/m) x (Y x 10^-R - b)        Y = the 2-byte two's complement word
+#
+#   Voltage      m=0.125  b=0  R=0   units mV   ->  X = Y x 8 mV
+#   Current      m=0.25   b=0  R=2   units A    ->  X = Y x 0.04 A
+#   Temperature  m=1      b=0  R=2   units degC ->  X = Y x 0.01 degC
+#
+# Sanity check: READ_VOUT 0x05D4 = 1492 -> 1492 x 8 = 11936 mV, which is exactly
+# what PDB_IBC_SWB1_A_VOUT reports in 'show platform voltage'.
+#
+# ⚠️ Table 3 does not list READ_VIN or READ_IIN. They are decoded here with the
+#    Voltage and Current coefficients respectively - reasonable, and consistent
+#    with a ~50 V input, but not stated by the datasheet. PB_VIN_M / PB_IIN_M
+#    below are where to change that if the part turns out to differ.
+#
+# ⚠️ CPB.PU37 (0x26) is a DIFFERENT part: no PAGE writes, and its own scaling
+#    (Vin 0.25 V, Vout 2^-11 V, Iout 0.5 A per count of the mantissa). Those
+#    three were confirmed against words this DUT returns.
+#
+# Usage:
+#   ./pwr_brick.sh show          # the table
+#   ./pwr_brick.sh show -r       # add the raw words
+#   ./pwr_brick.sh help
+# =============================================================================
+
+# --- User Configurable Section ----------------------------------------------
+PB_CH="${PB_CH:-4}"                    # ICB VI2C channel
+PB_MUX="${PB_MUX:-0x72}"               # TCA954x address
+PB_MUX_SEL="${PB_MUX_SEL:-0x01}"       # control byte: bit0 = channel 0
+PB_TRIES="${PB_TRIES:-8}"              # reads per value before giving up
+
+# PMBus PAGE per measurement (ADPM12200). Decimal page numbers written in hex.
+PB_PAGE_VIN="${PB_PAGE_VIN:-0x09}"     # 9
+PB_PAGE_IIN="${PB_PAGE_IIN:-0x0A}"     # 10
+PB_PAGE_VOUT="${PB_PAGE_VOUT:-0x02}"   # 2
+PB_PAGE_IOUT="${PB_PAGE_IOUT:-0x0E}"   # 14
+PB_PAGE_TEMP="${PB_PAGE_TEMP:-0x12}"   # 18
+
+# DIRECT coefficients: m, R, and the divisor that takes the datasheet unit to
+# the displayed unit (mV -> V is 1000; A and degC are already right).
+PB_VOUT_M="${PB_VOUT_M:-0.125}"; PB_VOUT_R="${PB_VOUT_R:-0}"; PB_VOUT_DIV="${PB_VOUT_DIV:-1000}"
+PB_VIN_M="${PB_VIN_M:-0.125}";   PB_VIN_R="${PB_VIN_R:-0}";   PB_VIN_DIV="${PB_VIN_DIV:-1000}"
+PB_IOUT_M="${PB_IOUT_M:-0.25}";  PB_IOUT_R="${PB_IOUT_R:-2}"; PB_IOUT_DIV="${PB_IOUT_DIV:-1}"
+PB_IIN_M="${PB_IIN_M:-0.25}";    PB_IIN_R="${PB_IIN_R:-2}";   PB_IIN_DIV="${PB_IIN_DIV:-1}"
+PB_TEMP_M="${PB_TEMP_M:-1}";     PB_TEMP_R="${PB_TEMP_R:-2}"; PB_TEMP_DIV="${PB_TEMP_DIV:-1}"
+
+# CPB.PU37 only (different part, no PAGE, mantissa-based)
+CPB_VIN_LSB="${CPB_VIN_LSB:-0.25}"     # V per count of the mantissa
+CPB_IOUT_LSB="${CPB_IOUT_LSB:-0.5}"    # A per count of the mantissa
+
+# Plausibility windows. A decoded value outside its window is discarded and the
+# read retried; this is what rejects the corrupted words this bus produces - a
+# bad high byte turns 11.98 V into 32.00 V, which "reject 0xFFFF" never catches.
+PB_VIN_LO="${PB_VIN_LO:-30}";    PB_VIN_HI="${PB_VIN_HI:-70}"
+PB_VOUT_LO="${PB_VOUT_LO:-8}";   PB_VOUT_HI="${PB_VOUT_HI:-14}"
+PB_IIN_LO="${PB_IIN_LO:-0}";     PB_IIN_HI="${PB_IIN_HI:-100}"
+PB_IOUT_LO="${PB_IOUT_LO:-0}";   PB_IOUT_HI="${PB_IOUT_HI:-300}"
+PB_TEMP_LO="${PB_TEMP_LO:-0}";   PB_TEMP_HI="${PB_TEMP_HI:-125}"
+
+# All-ones and all-zeros are the two ways this bus says "nobody answered", and
+# both can decode into a value that sits inside its window - 0x0000 on the
+# temperature register reads as a perfectly plausible 0 C. Rejected as raw
+# words, before any conversion, so no window has to be bent to catch them.
+PB_REJECT_FFFF="${PB_REJECT_FFFF:-1}"
+PB_REJECT_0000="${PB_REJECT_0000:-1}"
+
+# "location:bricks:slave:netname:kind"   kind = adpm (PAGE per read) | cpb
+PB_DEVS=(
+    "SWB0.PU207:BRICKS1:0x62:P12V_SWB0_L:adpm"
+    "SWB0.PU13:BRICKS2:0x63:P12V_SWB0_L:adpm"
+    "SWB1.PU332:BRICKS1:0x60:P12V_SWB1_R:adpm"
+    "SWB1.PU85:BRICKS2:0x61:P12V_SWB1_R:adpm"
+    "CPB.PU37:BRICK:0x26:P12V_STBY:cpb"
+)
+# -----------------------------------------------------------------------------
+
+PB_NA="NA"
+PB_RAW=0
+PB_DIR="$(cd "$(dirname "${BASH_SOURCE[0]}")" 2>/dev/null && pwd)"
+
+_pb_err() { echo -e "[\033[31mERR \033[0m] $*" >&2; }
+
+# --- backend -----------------------------------------------------------------
+if ! declare -F vi2c_read >/dev/null 2>&1; then
+    if [ -r "$PB_DIR/blanton_icb_vi2c.sh" ]; then
+        # shellcheck source=/dev/null
+        source "$PB_DIR/blanton_icb_vi2c.sh" >/dev/null 2>&1
+    else
+        _pb_err "blanton_icb_vi2c.sh not found next to this script"; exit 1
+    fi
+fi
+declare -F vi2c_read >/dev/null 2>&1 || { _pb_err "vi2c_read() still undefined"; exit 1; }
+
+# --- decoders ----------------------------------------------------------------
+# DIRECT: X = (1/m) x (Y x 10^-R - b), b = 0. Y is two's complement, so a word
+# above 0x7FFF is negative - that matters for temperature, not for the rails.
+_pb_direct() {
+    awk -v w=$(( $1 )) -v m="$2" -v r="$3" -v d="$4" 'BEGIN{
+        if (w > 32767) w -= 65536
+        printf "%.3f", ((w * (10 ^ -r)) / m) / d
+    }'
+}
+# SLINEAR11 mantissa only (bits[10:0], two's complement) - CPB.PU37 path.
+_pb_mant()  { awk -v w=$(( $1 )) 'BEGIN{ m = w % 2048; if (m > 1023) m -= 2048; print m }'; }
+_pb_mul()   { awk -v a="$1" -v b="$2" 'BEGIN{ printf "%.3f", a * b }'; }
+_pb_lin11() { awk -v w=$(( $1 )) 'BEGIN{ printf "%.4f", w * (2.0 ^ -11) }'; }
+_pb_in()    { awk -v x="$1" -v lo="$2" -v hi="$3" 'BEGIN{ exit !(x >= lo && x <= hi) }'; }
+
+# _pb_word <slave> <page|-> <reg>  -> "0xWWWW"
+_pb_word() {
+    local slave="$1" page="$2" reg="$3" out
+    [ "$page" != "-" ] && vi2c_write "$PB_CH" "$slave" 0x00 "$page" >/dev/null 2>&1
+    out=$(vi2c_read "$PB_CH" "$slave" "$reg" 2 2>/dev/null \
+          | sed -n 's/.*\[0x\(..\) 0x\(..\)\].*/0x\2\1/p')
+    [ -n "$out" ] && echo "$out"
+}
+
+# _pb_val <slave> <page|-> <reg> <decoder> <a1> <a2> <a3> <lo> <hi>
+# Retries until the decoded value lands inside the window; echoes "value raw".
+_pb_val() {
+    local slave="$1" page="$2" reg="$3" dec="$4" a1="$5" a2="$6" a3="$7" lo="$8" hi="$9"
+    local i w v
+    for (( i = 0; i < PB_TRIES; i++ )); do
+        w=$(_pb_word "$slave" "$page" "$reg") || continue
+        [ -z "$w" ] && continue
+        [ "$PB_REJECT_FFFF" = "1" ] && [ "$(( w ))" -eq 65535 ] && continue
+        [ "$PB_REJECT_0000" = "1" ] && [ "$(( w ))" -eq 0 ]     && continue
+        case "$dec" in
+            direct) v=$(_pb_direct "$w" "$a1" "$a2" "$a3") ;;
+            mant)   v=$(_pb_mul "$(_pb_mant "$w")" "$a1") ;;
+            lin11)  v=$(_pb_lin11 "$w") ;;
+        esac
+        _pb_in "$v" "$lo" "$hi" || continue
+        echo "$v $w"; return 0
+    done
+    echo "$PB_NA -"; return 1
+}
+
+_pb_mux_open() {
+    # The mux takes a bare control byte and vi2c_write always sends a register
+    # first, so passing 0x01 as both makes the part latch 0x01 either way.
+    vi2c_init "$PB_CH" >/dev/null 2>&1
+    vi2c_write "$PB_CH" "$PB_MUX" "$PB_MUX_SEL" "$PB_MUX_SEL" >/dev/null 2>&1
+    return 0
+}
+
+# --- show --------------------------------------------------------------------
+pwr_brick_show() {
+    _pb_mux_open
+    echo "==== PDB / CPB power bricks (VI2C ch${PB_CH} -> mux ${PB_MUX} ch0) ===="
+    printf '%-3s %-12s %-8s %-7s %-14s %10s %10s %10s %10s %9s\n' \
+        "No." "Location" "Bricks" "SlaveID" "Netname" \
+        "Vin(V)" "Iin(A)" "Vout(V)" "Iout(A)" "Temp(C)"
+    printf '%s\n' "--------------------------------------------------------------------------------------------------------------"
+
+    local n=0 entry loc bk slave net kind vi ii vo io tp
+    for entry in "${PB_DEVS[@]}"; do
+        IFS=':' read -r loc bk slave net kind <<< "$entry"
+        n=$(( n + 1 ))
+        if [ "$kind" = "cpb" ]; then
+            vi=$(_pb_val "$slave" - 0x88 mant  "$CPB_VIN_LSB"  "" "" "$PB_VIN_LO"  "$PB_VIN_HI")
+            ii="$PB_NA -"                                  # no input current on this part
+            vo=$(_pb_val "$slave" - 0x8B lin11 ""           "" "" "$PB_VOUT_LO" "$PB_VOUT_HI")
+            io=$(_pb_val "$slave" - 0x8C mant  "$CPB_IOUT_LSB" "" "" "$PB_IOUT_LO" "$PB_IOUT_HI")
+            tp=$(_pb_val "$slave" - 0x8D direct 1 2 1        "$PB_TEMP_LO" "$PB_TEMP_HI")
+        else
+            vi=$(_pb_val "$slave" "$PB_PAGE_VIN"  0x88 direct "$PB_VIN_M"  "$PB_VIN_R"  "$PB_VIN_DIV"  "$PB_VIN_LO"  "$PB_VIN_HI")
+            ii=$(_pb_val "$slave" "$PB_PAGE_IIN"  0x89 direct "$PB_IIN_M"  "$PB_IIN_R"  "$PB_IIN_DIV"  "$PB_IIN_LO"  "$PB_IIN_HI")
+            vo=$(_pb_val "$slave" "$PB_PAGE_VOUT" 0x8B direct "$PB_VOUT_M" "$PB_VOUT_R" "$PB_VOUT_DIV" "$PB_VOUT_LO" "$PB_VOUT_HI")
+            io=$(_pb_val "$slave" "$PB_PAGE_IOUT" 0x8C direct "$PB_IOUT_M" "$PB_IOUT_R" "$PB_IOUT_DIV" "$PB_IOUT_LO" "$PB_IOUT_HI")
+            tp=$(_pb_val "$slave" "$PB_PAGE_TEMP" 0x8D direct "$PB_TEMP_M" "$PB_TEMP_R" "$PB_TEMP_DIV" "$PB_TEMP_LO" "$PB_TEMP_HI")
+        fi
+        printf '%-3s %-12s %-8s %-7s %-14s %10s %10s %10s %10s %9s\n' \
+            "$n" "$loc" "$bk" "$slave" "$net" \
+            "${vi%% *}" "${ii%% *}" "${vo%% *}" "${io%% *}" "${tp%% *}"
+        [ "$PB_RAW" = "1" ] && printf '%-3s %-12s %-8s %-7s %-14s %10s %10s %10s %10s %9s\n' \
+            "" "" "" "" "raw" "${vi##* }" "${ii##* }" "${vo##* }" "${io##* }" "${tp##* }"
+    done
+    # No trailing notes on stdout: this table gets pasted into reports and
+    # captured into the master console log, and a caveat printed every run stops
+    # being read after the second time. The caveats live in the file header -
+    # the one that still matters is that READ_VIN / READ_IIN are not in the
+    # datasheet coefficient table and borrow the Voltage / Current sets.
+}
+
+pwr_brick_help() {
+    echo -e "\033[1mpwr_brick.sh - PDB / CPB power brick readings\033[0m"
+    echo ""
+    echo -e "  \033[33mshow\033[0m [-r]   Vin / Iin / Vout / Iout / Temp for all 5 bricks (-r adds raw)"
+    echo -e "  \033[33mhelp\033[0m"
+    echo ""
+    echo -e "  Path : VI2C ch$PB_CH -> mux $PB_MUX ch0"
+    echo -e "  The four ADPM12200 modules need a PMBus PAGE per measurement:"
+    echo -e "    Vin $PB_PAGE_VIN(9)  Iin $PB_PAGE_IIN(10)  Vout $PB_PAGE_VOUT(2)  Iout $PB_PAGE_IOUT(14)  Temp $PB_PAGE_TEMP(18)"
+    echo -e "  DIRECT format, datasheet Table 3:  X = (1/m) x (Y x 10^-R - b)"
+    echo -e "  CPB.PU37 (0x26) is a different part - no PAGE, its own scaling."
+    echo -e "  \033[33mREAD_VIN / READ_IIN are not in Table 3; they borrow Voltage / Current.\033[0m"
+}
+
+case "${1:-help}" in
+    show)
+        shift 2>/dev/null
+        [ "${1:-}" = "-r" ] && PB_RAW=1
+        pwr_brick_show ;;
+    help|-h|--help) pwr_brick_help ;;
+    *) _pb_err "unknown sub-command: $1"; pwr_brick_help; exit 1 ;;
+esac

tools/Multiphase_Netname

@@ -0,0 +1,40 @@
+SWB0_0V9_ANLG0
+SWB0_0V9_ANLG1
+SWB0_0V75_ANLG0
+SWB0_0V75_ANLG1
+SWB0_PHYTILE_P0
+SWB0_PHYTILE_P1
+SWB0_PHYTILE_P2
+SWB0_PHYTILE_P3
+SWB0_PHYTILE_P4
+SWB0_PHYTILE_P5
+SWB0_PHYTILE_P6
+SWB0_PHYTILE_P7
+SWB0_PVDD1V5_CNDR0
+SWB0_PVDD1V5_CNDR1
+SWB0_PVDDA_PHYT0
+SWB0_PVDDA_PHYT1
+SWB0_PVDDA_PHYT2
+SWB0_PVDDA_PHYT3
+SWB0_TH6_CORE
+
+
+SWB1_0V9_ANLG0
+SWB1_0V9_ANLG1
+SWB1_0V75_ANLG0
+SWB1_0V75_ANLG1
+SWB1_PHYTILE_P0
+SWB1_PHYTILE_P1
+SWB1_PHYTILE_P2
+SWB1_PHYTILE_P3
+SWB1_PHYTILE_P4
+SWB1_PHYTILE_P5
+SWB1_PHYTILE_P6
+SWB1_PHYTILE_P7
+SWB1_PVDD1V5_CNDR0
+SWB1_PVDD1V5_CNDR1
+SWB1_PVDDA_PHYT0
+SWB1_PVDDA_PHYT1
+SWB1_PVDDA_PHYT2
+SWB1_PVDDA_PHYT3
+SWB1_TH6_CORE

tools/Multiphase_Normal.txt

@@ -0,0 +1,188 @@
+//0.900V (nominal)
+i2cset -f -y 13 0x25 0x00 0
+i2ctransfer -f -y 13 w3@0x25 0x21 0x83 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x0D 0x74 0x10
+//0.900V (nominal)
+i2cset -f -y 15 0x26 0x00 0
+i2ctransfer -f -y 15 w3@0x26 0x21 0x83 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x0D 0x74 0x10
+//0.75V (nominal)
+i2cset -f -y 13 0x25 0x00 1
+i2ctransfer -f -y 13 w3@0x25 0x21 0x65 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 15 0x26 0x00 1
+i2ctransfer -f -y 15 w3@0x26 0x21 0x65 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 13 0x21 0x00 0
+i2ctransfer -f -y 13 w3@0x21 0x21 0x65 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x0D 0xB2 0x0C
+//0.75V (nominal)
+i2cset -f -y 13 0x21 0x00 1
+i2ctransfer -f -y 13 w3@0x21 0x21 0x65 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 13 0x22 0x00 0
+i2ctransfer -f -y 13 w3@0x22 0x21 0x65 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x0D 0xB2 0x0C
+//0.75V (nominal)
+i2cset -f -y 13 0x22 0x00 1
+i2ctransfer -f -y 13 w3@0x22 0x21 0x65 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 15 0x23 0x00 0
+i2ctransfer -f -y 15 w3@0x23 0x21 0x65 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x0D 0xB2 0x0C
+//0.75V (nominal)
+i2cset -f -y 15 0x23 0x00 1
+i2ctransfer -f -y 15 w3@0x23 0x21 0x65 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 15 0x24 0x00 0
+i2ctransfer -f -y 15 w3@0x24 0x21 0x65 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x0D 0xB2 0x0C
+//0.75V (nominal)
+i2cset -f -y 15 0x24 0x00 1
+i2ctransfer -f -y 15 w3@0x24 0x21 0x65 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x1D 0x5A 0x06
+//1.5V (nominal)
+i2cset -f -y 13 0x29 0x00 0
+i2ctransfer -f -y 13 w3@0x29 0x21 0xFB 0x00
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x0D 0x71 0x1F
+//1.5V (nominal)
+i2cset -f -y 13 0x29 0x00 1
+i2ctransfer -f -y 13 w3@0x29 0x21 0xFB 0x00
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x1D 0xB9 0x0F
+//0.720V
+i2cset -f -y 13 0x27 0x00 0
+i2ctransfer -f -y 13 w3@0x27 0x21 0x5F 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x0D 0xF4 0x0B
+//0.720V
+i2cset -f -y 13 0x27 0x00 1
+i2ctransfer -f -y 13 w3@0x27 0x21 0x5F 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x1D 0xFC 0x05
+//0.720V
+i2cset -f -y 15 0x28 0x00 0
+i2ctransfer -f -y 15 w3@0x28 0x21 0x5F 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x0D 0xF4 0x0B
+//0.720V
+i2cset -f -y 15 0x28 0x00 1
+i2ctransfer -f -y 15 w3@0x28 0x21 0x5F 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x1D 0xFC 0x05
+//0.8V(nominal) , 0.8591V with load line
+i2cset -f -y 13 0x20 0x00 0
+i2ctransfer -f -y 13 w3@0x20 0x21 0x57 0x01
+
+
+//0.900V (nominal)
+i2cset -f -y 14 0x25 0x00 0
+i2ctransfer -f -y 14 w3@0x25 0x21 0x83 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x0D 0x74 0x10
+//0.900V (nominal)
+i2cset -f -y 16 0x26 0x00 0
+i2ctransfer -f -y 16 w3@0x26 0x21 0x83 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x0D 0x74 0x10
+//0.75V (nominal)
+i2cset -f -y 14 0x25 0x00 1
+i2ctransfer -f -y 14 w3@0x25 0x21 0x65 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 16 0x26 0x00 1
+i2ctransfer -f -y 16 w3@0x26 0x21 0x65 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 14 0x21 0x00 0
+i2ctransfer -f -y 14 w3@0x21 0x21 0x65 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x0D 0xB2 0x0C
+//0.75V (nominal)
+i2cset -f -y 14 0x21 0x00 1
+i2ctransfer -f -y 14 w3@0x21 0x21 0x65 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 14 0x22 0x00 0
+i2ctransfer -f -y 14 w3@0x22 0x21 0x65 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x0D 0xB2 0x0C
+//0.75V (nominal)
+i2cset -f -y 14 0x22 0x00 1
+i2ctransfer -f -y 14 w3@0x22 0x21 0x65 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 16 0x23 0x00 0
+i2ctransfer -f -y 16 w3@0x23 0x21 0x65 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x0D 0xB2 0x0C
+//0.75V (nominal)
+i2cset -f -y 16 0x23 0x00 1
+i2ctransfer -f -y 16 w3@0x23 0x21 0x65 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x1D 0x5A 0x06
+//0.75V (nominal)
+i2cset -f -y 16 0x24 0x00 0
+i2ctransfer -f -y 16 w3@0x24 0x21 0x65 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x0D 0xB2 0x0C
+//0.75V (nominal)
+i2cset -f -y 16 0x24 0x00 1
+i2ctransfer -f -y 16 w3@0x24 0x21 0x65 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x1D 0x5A 0x06
+//1.5V (nominal)
+i2cset -f -y 14 0x29 0x00 0
+i2ctransfer -f -y 14 w3@0x29 0x21 0xFB 0x00
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x0D 0x71 0x1F
+//1.5V (nominal)
+i2cset -f -y 14 0x29 0x00 1
+i2ctransfer -f -y 14 w3@0x29 0x21 0xFB 0x00
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x1D 0xB9 0x0F
+//0.720V (nominal)
+i2cset -f -y 14 0x27 0x00 0
+i2ctransfer -f -y 14 w3@0x27 0x21 0x5F 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x0D 0xF4 0x0B
+//0.720V (nominal)
+i2cset -f -y 14 0x27 0x00 1
+i2ctransfer -f -y 14 w3@0x27 0x21 0x5F 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x1D 0xFC 0x05
+//0.720V (nominal)
+i2cset -f -y 16 0x28 0x00 0
+i2ctransfer -f -y 16 w3@0x28 0x21 0x5F 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x0D 0xF4 0x0B
+//0.720V (nominal)
+i2cset -f -y 16 0x28 0x00 1
+i2ctransfer -f -y 16 w3@0x28 0x21 0x5F 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x1D 0xFC 0x05
+//0.8V(nominal) , 0.8591V with load line
+i2cset -f -y 14 0x20 0x00 0
+i2ctransfer -f -y 14 w3@0x20 0x21 0x57 0x01

tools/Multiphase_Save.txt

@@ -0,0 +1,48 @@
+i2cset -f -y 13 0x25 0x00 0
+i2cset -f -y 13 0x25 0x15
+i2cset -f -y 15 0x26 0x00 0
+i2cset -f -y 15 0x26 0x15
+i2cset -f -y 13 0x25 0x00 0
+i2cset -f -y 13 0x25 0x15
+i2cset -f -y 15 0x26 0x00 0
+i2cset -f -y 15 0x26 0x15
+i2cset -f -y 13 0x21 0x00 0
+i2cset -f -y 13 0x21 0x15
+i2cset -f -y 13 0x22 0x00 0
+i2cset -f -y 13 0x22 0x15
+i2cset -f -y 15 0x23 0x00 0
+i2cset -f -y 15 0x23 0x15
+i2cset -f -y 15 0x24 0x00 0
+i2cset -f -y 15 0x24 0x15
+i2cset -f -y 13 0x29 0x00 0
+i2cset -f -y 13 0x29 0x15
+i2cset -f -y 13 0x27 0x00 0
+i2cset -f -y 13 0x27 0x15
+i2cset -f -y 15 0x28 0x00 0
+i2cset -f -y 15 0x28 0x15
+i2cset -f -y 13 0x20 0x00 0
+i2cset -f -y 13 0x20 0x17
+i2cset -f -y 14 0x25 0x00 0
+i2cset -f -y 14 0x25 0x15
+i2cset -f -y 16 0x26 0x00 0
+i2cset -f -y 16 0x26 0x15
+i2cset -f -y 14 0x25 0x00 0
+i2cset -f -y 14 0x25 0x15
+i2cset -f -y 16 0x26 0x00 0
+i2cset -f -y 16 0x26 0x15
+i2cset -f -y 14 0x21 0x00 0
+i2cset -f -y 14 0x21 0x15
+i2cset -f -y 14 0x22 0x00 0
+i2cset -f -y 14 0x22 0x15
+i2cset -f -y 16 0x23 0x00 0
+i2cset -f -y 16 0x23 0x15
+i2cset -f -y 16 0x24 0x00 0
+i2cset -f -y 16 0x24 0x15
+i2cset -f -y 14 0x29 0x00 0
+i2cset -f -y 14 0x29 0x15
+i2cset -f -y 14 0x27 0x00 0
+i2cset -f -y 14 0x27 0x15
+i2cset -f -y 16 0x28 0x00 0
+i2cset -f -y 16 0x28 0x15
+i2cset -f -y 14 0x20 0x00 0
+i2cset -f -y 14 0x20 0x17

tools/Multiphase_comboA.txt

@@ -0,0 +1,188 @@
+//0.930V
+i2cset -f -y 13 0x25 0x00 0
+i2ctransfer -f -y 13 w3@0x25 0x21 0x89 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x0D 0x34 0x11
+//0.930V
+i2cset -f -y 15 0x26 0x00 0
+i2ctransfer -f -y 15 w3@0x26 0x21 0x89 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x0D 0x34 0x11
+//0.725V
+i2cset -f -y 13 0x25 0x00 1
+i2ctransfer -f -y 13 w3@0x25 0x21 0x60 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 15 0x26 0x00 1
+i2ctransfer -f -y 15 w3@0x26 0x21 0x60 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 13 0x21 0x00 0
+i2ctransfer -f -y 13 w3@0x21 0x21 0x60 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 13 0x21 0x00 1
+i2ctransfer -f -y 13 w3@0x21 0x21 0x60 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 13 0x22 0x00 0
+i2ctransfer -f -y 13 w3@0x22 0x21 0x60 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 13 0x22 0x00 1
+i2ctransfer -f -y 13 w3@0x22 0x21 0x60 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 15 0x23 0x00 0
+i2ctransfer -f -y 15 w3@0x23 0x21 0x60 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 15 0x23 0x00 1
+i2ctransfer -f -y 15 w3@0x23 0x21 0x60 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 15 0x24 0x00 0
+i2ctransfer -f -y 15 w3@0x24 0x21 0x60 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 15 0x24 0x00 1
+i2ctransfer -f -y 15 w3@0x24 0x21 0x60 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x1D 0x0A 0x06
+//1.545V
+i2cset -f -y 13 0x29 0x00 0
+i2ctransfer -f -y 13 w3@0x29 0x21 0x04 0x01
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x0D 0x91 0x20
+//1.545V
+i2cset -f -y 13 0x29 0x00 1
+i2ctransfer -f -y 13 w3@0x29 0x21 0x04 0x01
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x1D 0x49 0x10
+//0.745V
+i2cset -f -y 13 0x27 0x00 0
+i2ctransfer -f -y 13 w3@0x27 0x21 0x64 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x0D 0x94 0x0C
+//0.745V
+i2cset -f -y 13 0x27 0x00 1
+i2ctransfer -f -y 13 w3@0x27 0x21 0x64 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x1D 0x4C 0x06
+//0.745V
+i2cset -f -y 15 0x28 0x00 0
+i2ctransfer -f -y 15 w3@0x28 0x21 0x64 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x0D 0x94 0x0C
+//0.745V
+i2cset -f -y 15 0x28 0x00 1
+i2ctransfer -f -y 15 w3@0x28 0x21 0x64 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x1D 0x4C 0x06
+//0.885V
+i2cset -f -y 13 0x20 0x00 0
+i2ctransfer -f -y 13 w3@0x20 0x21 0x62 0x01
+
+
+//0.930V
+i2cset -f -y 14 0x25 0x00 0
+i2ctransfer -f -y 14 w3@0x25 0x21 0x89 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x0D 0x34 0x11
+//0.930V
+i2cset -f -y 16 0x26 0x00 0
+i2ctransfer -f -y 16 w3@0x26 0x21 0x89 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x0D 0x34 0x11
+//0.725V
+i2cset -f -y 14 0x25 0x00 1
+i2ctransfer -f -y 14 w3@0x25 0x21 0x60 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 16 0x26 0x00 1
+i2ctransfer -f -y 16 w3@0x26 0x21 0x60 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 14 0x21 0x00 0
+i2ctransfer -f -y 14 w3@0x21 0x21 0x60 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 14 0x21 0x00 1
+i2ctransfer -f -y 14 w3@0x21 0x21 0x60 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 14 0x22 0x00 0
+i2ctransfer -f -y 14 w3@0x22 0x21 0x60 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 14 0x22 0x00 1
+i2ctransfer -f -y 14 w3@0x22 0x21 0x60 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 16 0x23 0x00 0
+i2ctransfer -f -y 16 w3@0x23 0x21 0x60 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 16 0x23 0x00 1
+i2ctransfer -f -y 16 w3@0x23 0x21 0x60 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 16 0x24 0x00 0
+i2ctransfer -f -y 16 w3@0x24 0x21 0x60 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 16 0x24 0x00 1
+i2ctransfer -f -y 16 w3@0x24 0x21 0x60 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x1D 0x0A 0x06
+//1.545V
+i2cset -f -y 14 0x29 0x00 0
+i2ctransfer -f -y 14 w3@0x29 0x21 0x04 0x01
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x0D 0x91 0x20
+//1.545V
+i2cset -f -y 14 0x29 0x00 1
+i2ctransfer -f -y 14 w3@0x29 0x21 0x04 0x01
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x1D 0x49 0x10
+//0.745V
+i2cset -f -y 14 0x27 0x00 0
+i2ctransfer -f -y 14 w3@0x27 0x21 0x64 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x0D 0x94 0x0C
+//0.745V
+i2cset -f -y 14 0x27 0x00 1
+i2ctransfer -f -y 14 w3@0x27 0x21 0x64 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x1D 0x4C 0x06
+//0.745V
+i2cset -f -y 16 0x28 0x00 0
+i2ctransfer -f -y 16 w3@0x28 0x21 0x64 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x0D 0x94 0x0C
+//0.745V
+i2cset -f -y 16 0x28 0x00 1
+i2ctransfer -f -y 16 w3@0x28 0x21 0x64 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x1D 0x4C 0x06
+//0.885V
+i2cset -f -y 14 0x20 0x00 0
+i2ctransfer -f -y 14 w3@0x20 0x21 0x62 0x01

tools/Multiphase_comboB.txt

@@ -0,0 +1,188 @@
+//0.870V
+i2cset -f -y 13 0x25 0x00 0
+i2ctransfer -f -y 13 w3@0x25 0x21 0x7D 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x0D 0xB4 0x0F
+//0.870V
+i2cset -f -y 15 0x26 0x00 0
+i2ctransfer -f -y 15 w3@0x26 0x21 0x7D 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x0D 0xB4 0x0F
+//0.775V
+i2cset -f -y 13 0x25 0x00 1
+i2ctransfer -f -y 13 w3@0x25 0x21 0x6A 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 15 0x26 0x00 1
+i2ctransfer -f -y 15 w3@0x26 0x21 0x6A 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 13 0x21 0x00 0
+i2ctransfer -f -y 13 w3@0x21 0x21 0x6A 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x0D 0x52 0x0D
+//0.775V
+i2cset -f -y 13 0x21 0x00 1
+i2ctransfer -f -y 13 w3@0x21 0x21 0x6A 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 13 0x22 0x00 0
+i2ctransfer -f -y 13 w3@0x22 0x21 0x6A 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x0D 0x52 0x0D
+//0.775V
+i2cset -f -y 13 0x22 0x00 1
+i2ctransfer -f -y 13 w3@0x22 0x21 0x6A 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 15 0x23 0x00 0
+i2ctransfer -f -y 15 w3@0x23 0x21 0x6A 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x0D  0x52 0x0D
+//0.775V
+i2cset -f -y 15 0x23 0x00 1
+i2ctransfer -f -y 15 w3@0x23 0x21 0x6A 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 15 0x24 0x00 0
+i2ctransfer -f -y 15 w3@0x24 0x21 0x6A 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x0D  0x52 0x0D
+//0.775V
+i2cset -f -y 15 0x24 0x00 1
+i2ctransfer -f -y 15 w3@0x24 0x21 0x6A 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x1D 0xAA 0x06
+//1.455V
+i2cset -f -y 13 0x29 0x00 0
+i2ctransfer -f -y 13 w3@0x29 0x21 0xF2 0x00
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x0D 0x51 0x1E
+//1.455V
+i2cset -f -y 13 0x29 0x00 1
+i2ctransfer -f -y 13 w3@0x29 0x21 0xF2 0x00
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x1D 0x29 0x0F
+//0.695V
+i2cset -f -y 13 0x27 0x00 0
+i2ctransfer -f -y 13 w3@0x27 0x21 0x5A 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x0D 0x54 0x0B
+//0.695V
+i2cset -f -y 13 0x27 0x00 1
+i2ctransfer -f -y 13 w3@0x27 0x21 0x5A 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x1D 0xAC 0x05
+//0.695V
+i2cset -f -y 15 0x28 0x00 0
+i2ctransfer -f -y 15 w3@0x28 0x21 0x5A 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x0D 0x54 0x0B
+//0.695V
+i2cset -f -y 15 0x28 0x00 1
+i2ctransfer -f -y 15 w3@0x28 0x21 0x5A 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x1D 0xAC 0x05
+//0.753V
+i2cset -f -y 13 0x20 0x00 0
+i2ctransfer -f -y 13 w3@0x20 0x21 0x2D 0x01
+
+
+//0.870V
+i2cset -f -y 14 0x25 0x00 0
+i2ctransfer -f -y 14 w3@0x25 0x21 0x7D 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x0D 0xB4 0x0F
+//0.870V
+i2cset -f -y 16 0x26 0x00 0
+i2ctransfer -f -y 16 w3@0x26 0x21 0x7D 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x0D 0xB4 0x0F
+//0.775V
+i2cset -f -y 14 0x25 0x00 1
+i2ctransfer -f -y 14 w3@0x25 0x21 0x6A 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 16 0x26 0x00 1
+i2ctransfer -f -y 16 w3@0x26 0x21 0x6A 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 14 0x21 0x00 0
+i2ctransfer -f -y 14 w3@0x21 0x21 0x6A 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x0D 0x52 0x0D
+//0.775V
+i2cset -f -y 14 0x21 0x00 1
+i2ctransfer -f -y 14 w3@0x21 0x21 0x6A 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 14 0x22 0x00 0
+i2ctransfer -f -y 14 w3@0x22 0x21 0x6A 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x0D 0x52 0x0D
+//0.775V
+i2cset -f -y 14 0x22 0x00 1
+i2ctransfer -f -y 14 w3@0x22 0x21 0x6A 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 16 0x23 0x00 0
+i2ctransfer -f -y 16 w3@0x23 0x21 0x6A 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x0D  0x52 0x0D
+//0.775V
+i2cset -f -y 16 0x23 0x00 1
+i2ctransfer -f -y 16 w3@0x23 0x21 0x6A 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 16 0x24 0x00 0
+i2ctransfer -f -y 16 w3@0x24 0x21 0x6A 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x0D  0x52 0x0D
+//0.775V
+i2cset -f -y 16 0x24 0x00 1
+i2ctransfer -f -y 16 w3@0x24 0x21 0x6A 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x1D 0xAA 0x06
+//1.455V
+i2cset -f -y 14 0x29 0x00 0
+i2ctransfer -f -y 14 w3@0x29 0x21 0xF2 0x00
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x0D 0x51 0x1E
+//1.455V
+i2cset -f -y 14 0x29 0x00 1
+i2ctransfer -f -y 14 w3@0x29 0x21 0xF2 0x00
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x1D 0x29 0x0F
+//0.695V
+i2cset -f -y 14 0x27 0x00 0
+i2ctransfer -f -y 14 w3@0x27 0x21 0x5A 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x0D 0x54 0x0B
+//0.695V
+i2cset -f -y 14 0x27 0x00 1
+i2ctransfer -f -y 14 w3@0x27 0x21 0x5A 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x1D 0xAC 0x05
+//0.695V
+i2cset -f -y 16 0x28 0x00 0
+i2ctransfer -f -y 16 w3@0x28 0x21 0x5A 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x0D 0x54 0x0B
+//0.695V
+i2cset -f -y 16 0x28 0x00 1
+i2ctransfer -f -y 16 w3@0x28 0x21 0x5A 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x1D 0xAC 0x05
+//0.753V
+i2cset -f -y 14 0x20 0x00 0
+i2ctransfer -f -y 14 w3@0x20 0x21 0x2D 0x01

tools/Multiphase_high3.txt

@@ -0,0 +1,188 @@
+//0.930V
+i2cset -f -y 13 0x25 0x00 0
+i2ctransfer -f -y 13 w3@0x25 0x21 0x89 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x0D 0x34 0x11
+//0.930V
+i2cset -f -y 15 0x26 0x00 0
+i2ctransfer -f -y 15 w3@0x26 0x21 0x89 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x0D 0x34 0x11
+//0.775V
+i2cset -f -y 13 0x25 0x00 1
+i2ctransfer -f -y 13 w3@0x25 0x21 0x6A 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 15 0x26 0x00 1
+i2ctransfer -f -y 15 w3@0x26 0x21 0x6A 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 13 0x21 0x00 0
+i2ctransfer -f -y 13 w3@0x21 0x21 0x6A 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x0D 0x52 0x0D
+//0.775V
+i2cset -f -y 13 0x21 0x00 1
+i2ctransfer -f -y 13 w3@0x21 0x21 0x6A 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 13 0x22 0x00 0
+i2ctransfer -f -y 13 w3@0x22 0x21 0x6A 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x0D 0x52 0x0D
+//0.775V
+i2cset -f -y 13 0x22 0x00 1
+i2ctransfer -f -y 13 w3@0x22 0x21 0x6A 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 15 0x23 0x00 0
+i2ctransfer -f -y 15 w3@0x23 0x21 0x6A 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x0D  0x52 0x0D
+//0.775V
+i2cset -f -y 15 0x23 0x00 1
+i2ctransfer -f -y 15 w3@0x23 0x21 0x6A 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 15 0x24 0x00 0
+i2ctransfer -f -y 15 w3@0x24 0x21 0x6A 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x0D  0x52 0x0D
+//0.775V
+i2cset -f -y 15 0x24 0x00 1
+i2ctransfer -f -y 15 w3@0x24 0x21 0x6A 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x1D 0xAA 0x06
+//1.545V
+i2cset -f -y 13 0x29 0x00 0
+i2ctransfer -f -y 13 w3@0x29 0x21 0x04 0x01
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x0D 0x91 0x20
+//1.545V
+i2cset -f -y 13 0x29 0x00 1
+i2ctransfer -f -y 13 w3@0x29 0x21 0x04 0x01
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x1D 0x49 0x10
+//0.745V
+i2cset -f -y 13 0x27 0x00 0
+i2ctransfer -f -y 13 w3@0x27 0x21 0x64 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x0D 0x94 0x0C
+//0.745V
+i2cset -f -y 13 0x27 0x00 1
+i2ctransfer -f -y 13 w3@0x27 0x21 0x64 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x1D 0x4C 0x06
+//0.745V
+i2cset -f -y 15 0x28 0x00 0
+i2ctransfer -f -y 15 w3@0x28 0x21 0x64 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x0D 0x94 0x0C
+//0.745V
+i2cset -f -y 15 0x28 0x00 1
+i2ctransfer -f -y 15 w3@0x28 0x21 0x64 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x1D 0x4C 0x06
+//0.885V
+i2cset -f -y 13 0x20 0x00 0
+i2ctransfer -f -y 13 w3@0x20 0x21 0x62 0x01
+
+
+//0.930V
+i2cset -f -y 14 0x25 0x00 0
+i2ctransfer -f -y 14 w3@0x25 0x21 0x89 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x0D 0x34 0x11
+//0.930V
+i2cset -f -y 16 0x26 0x00 0
+i2ctransfer -f -y 16 w3@0x26 0x21 0x89 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x0D 0x34 0x11
+//0.775V
+i2cset -f -y 14 0x25 0x00 1
+i2ctransfer -f -y 14 w3@0x25 0x21 0x6A 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 16 0x26 0x00 1
+i2ctransfer -f -y 16 w3@0x26 0x21 0x6A 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 14 0x21 0x00 0
+i2ctransfer -f -y 14 w3@0x21 0x21 0x6A 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x0D 0x52 0x0D
+//0.775V
+i2cset -f -y 14 0x21 0x00 1
+i2ctransfer -f -y 14 w3@0x21 0x21 0x6A 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 14 0x22 0x00 0
+i2ctransfer -f -y 14 w3@0x22 0x21 0x6A 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x0D 0x52 0x0D
+//0.775V
+i2cset -f -y 14 0x22 0x00 1
+i2ctransfer -f -y 14 w3@0x22 0x21 0x6A 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 16 0x23 0x00 0
+i2ctransfer -f -y 16 w3@0x23 0x21 0x6A 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x0D  0x52 0x0D
+//0.775V
+i2cset -f -y 16 0x23 0x00 1
+i2ctransfer -f -y 16 w3@0x23 0x21 0x6A 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x1D 0xAA 0x06
+//0.775V
+i2cset -f -y 16 0x24 0x00 0
+i2ctransfer -f -y 16 w3@0x24 0x21 0x6A 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x0D  0x52 0x0D
+//0.775V
+i2cset -f -y 16 0x24 0x00 1
+i2ctransfer -f -y 16 w3@0x24 0x21 0x6A 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x1D 0xAA 0x06
+//1.545V
+i2cset -f -y 14 0x29 0x00 0
+i2ctransfer -f -y 14 w3@0x29 0x21 0x04 0x01
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x0D 0x91 0x20
+//1.545V
+i2cset -f -y 14 0x29 0x00 1
+i2ctransfer -f -y 14 w3@0x29 0x21 0x04 0x01
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x1D 0x49 0x10
+//0.745V
+i2cset -f -y 14 0x27 0x00 0
+i2ctransfer -f -y 14 w3@0x27 0x21 0x64 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x0D 0x94 0x0C
+//0.745V
+i2cset -f -y 14 0x27 0x00 1
+i2ctransfer -f -y 14 w3@0x27 0x21 0x64 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x1D 0x4C 0x06
+//0.745V
+i2cset -f -y 16 0x28 0x00 0
+i2ctransfer -f -y 16 w3@0x28 0x21 0x64 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x0D 0x94 0x0C
+//0.745V
+i2cset -f -y 16 0x28 0x00 1
+i2ctransfer -f -y 16 w3@0x28 0x21 0x64 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x1D 0x4C 0x06
+//0.885V
+i2cset -f -y 14 0x20 0x00 0
+i2ctransfer -f -y 14 w3@0x20 0x21 0x62 0x01

tools/Multiphase_low3.txt

@@ -0,0 +1,188 @@
+//0.870V
+i2cset -f -y 13 0x25 0x00 0
+i2ctransfer -f -y 13 w3@0x25 0x21 0x7D 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x0D 0xB4 0x0F
+//0.870V
+i2cset -f -y 15 0x26 0x00 0
+i2ctransfer -f -y 15 w3@0x26 0x21 0x7D 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x0D 0xB4 0x0F
+//0.725V
+i2cset -f -y 13 0x25 0x00 1
+i2ctransfer -f -y 13 w3@0x25 0x21 0x60 0x00
+i2cset -f -y 13 0x25 0x00 2
+i2ctransfer -f -y 13 w3@0x25 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 15 0x26 0x00 1
+i2ctransfer -f -y 15 w3@0x26 0x21 0x60 0x00
+i2cset -f -y 15 0x26 0x00 2
+i2ctransfer -f -y 15 w3@0x26 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 13 0x21 0x00 0
+i2ctransfer -f -y 13 w3@0x21 0x21 0x60 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 13 0x21 0x00 1
+i2ctransfer -f -y 13 w3@0x21 0x21 0x60 0x00
+i2cset -f -y 13 0x21 0x00 2
+i2ctransfer -f -y 13 w3@0x21 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 13 0x22 0x00 0
+i2ctransfer -f -y 13 w3@0x22 0x21 0x60 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 13 0x22 0x00 1
+i2ctransfer -f -y 13 w3@0x22 0x21 0x60 0x00
+i2cset -f -y 13 0x22 0x00 2
+i2ctransfer -f -y 13 w3@0x22 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 15 0x23 0x00 0
+i2ctransfer -f -y 15 w3@0x23 0x21 0x60 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 15 0x23 0x00 1
+i2ctransfer -f -y 15 w3@0x23 0x21 0x60 0x00
+i2cset -f -y 15 0x23 0x00 2
+i2ctransfer -f -y 15 w3@0x23 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 15 0x24 0x00 0
+i2ctransfer -f -y 15 w3@0x24 0x21 0x60 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 15 0x24 0x00 1
+i2ctransfer -f -y 15 w3@0x24 0x21 0x60 0x00
+i2cset -f -y 15 0x24 0x00 2
+i2ctransfer -f -y 15 w3@0x24 0x1D 0x0A 0x06
+//1.455V
+i2cset -f -y 13 0x29 0x00 0
+i2ctransfer -f -y 13 w3@0x29 0x21 0xF2 0x00
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x0D 0x51 0x1E
+//1.455V
+i2cset -f -y 13 0x29 0x00 1
+i2ctransfer -f -y 13 w3@0x29 0x21 0xF2 0x00
+i2cset -f -y 13 0x29 0x00 2
+i2ctransfer -f -y 13 w3@0x29 0x1D 0x29 0x0F
+//0.695V
+i2cset -f -y 13 0x27 0x00 0
+i2ctransfer -f -y 13 w3@0x27 0x21 0x5A 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x0D 0x54 0x0B
+//0.695V
+i2cset -f -y 13 0x27 0x00 1
+i2ctransfer -f -y 13 w3@0x27 0x21 0x5A 0x00
+i2cset -f -y 13 0x27 0x00 2
+i2ctransfer -f -y 13 w3@0x27 0x1D 0xAC 0x05
+//0.695V
+i2cset -f -y 15 0x28 0x00 0
+i2ctransfer -f -y 15 w3@0x28 0x21 0x5A 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x0D 0x54 0x0B
+//0.695V
+i2cset -f -y 15 0x28 0x00 1
+i2ctransfer -f -y 15 w3@0x28 0x21 0x5A 0x00
+i2cset -f -y 15 0x28 0x00 2
+i2ctransfer -f -y 15 w3@0x28 0x1D 0xAC 0x05
+//0.753V
+i2cset -f -y 13 0x20 0x00 0
+i2ctransfer -f -y 13 w3@0x20 0x21 0x2D 0x01
+
+
+//0.870V
+i2cset -f -y 14 0x25 0x00 0
+i2ctransfer -f -y 14 w3@0x25 0x21 0x7D 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x0D 0xB4 0x0F
+//0.870V
+i2cset -f -y 16 0x26 0x00 0
+i2ctransfer -f -y 16 w3@0x26 0x21 0x7D 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x0D 0xB4 0x0F
+//0.725V
+i2cset -f -y 14 0x25 0x00 1
+i2ctransfer -f -y 14 w3@0x25 0x21 0x60 0x00
+i2cset -f -y 14 0x25 0x00 2
+i2ctransfer -f -y 14 w3@0x25 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 16 0x26 0x00 1
+i2ctransfer -f -y 16 w3@0x26 0x21 0x60 0x00
+i2cset -f -y 16 0x26 0x00 2
+i2ctransfer -f -y 16 w3@0x26 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 14 0x21 0x00 0
+i2ctransfer -f -y 14 w3@0x21 0x21 0x60 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 14 0x21 0x00 1
+i2ctransfer -f -y 14 w3@0x21 0x21 0x60 0x00
+i2cset -f -y 14 0x21 0x00 2
+i2ctransfer -f -y 14 w3@0x21 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 14 0x22 0x00 0
+i2ctransfer -f -y 14 w3@0x22 0x21 0x60 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 14 0x22 0x00 1
+i2ctransfer -f -y 14 w3@0x22 0x21 0x60 0x00
+i2cset -f -y 14 0x22 0x00 2
+i2ctransfer -f -y 14 w3@0x22 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 16 0x23 0x00 0
+i2ctransfer -f -y 16 w3@0x23 0x21 0x60 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 16 0x23 0x00 1
+i2ctransfer -f -y 16 w3@0x23 0x21 0x60 0x00
+i2cset -f -y 16 0x23 0x00 2
+i2ctransfer -f -y 16 w3@0x23 0x1D 0x0A 0x06
+//0.725V
+i2cset -f -y 16 0x24 0x00 0
+i2ctransfer -f -y 16 w3@0x24 0x21 0x60 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x0D 0x12 0x0C
+//0.725V
+i2cset -f -y 16 0x24 0x00 1
+i2ctransfer -f -y 16 w3@0x24 0x21 0x60 0x00
+i2cset -f -y 16 0x24 0x00 2
+i2ctransfer -f -y 16 w3@0x24 0x1D 0x0A 0x06
+//1.455V
+i2cset -f -y 14 0x29 0x00 0
+i2ctransfer -f -y 14 w3@0x29 0x21 0xF2 0x00
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x0D 0x51 0x1E
+//1.455V
+i2cset -f -y 14 0x29 0x00 1
+i2ctransfer -f -y 14 w3@0x29 0x21 0xF2 0x00
+i2cset -f -y 14 0x29 0x00 2
+i2ctransfer -f -y 14 w3@0x29 0x1D 0x29 0x0F
+//0.695V
+i2cset -f -y 14 0x27 0x00 0
+i2ctransfer -f -y 14 w3@0x27 0x21 0x5A 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x0D 0x54 0x0B
+//0.695V
+i2cset -f -y 14 0x27 0x00 1
+i2ctransfer -f -y 14 w3@0x27 0x21 0x5A 0x00
+i2cset -f -y 14 0x27 0x00 2
+i2ctransfer -f -y 14 w3@0x27 0x1D 0xAC 0x05
+//0.695V
+i2cset -f -y 16 0x28 0x00 0
+i2ctransfer -f -y 16 w3@0x28 0x21 0x5A 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x0D 0x54 0x0B
+//0.695V
+i2cset -f -y 16 0x28 0x00 1
+i2ctransfer -f -y 16 w3@0x28 0x21 0x5A 0x00
+i2cset -f -y 16 0x28 0x00 2
+i2ctransfer -f -y 16 w3@0x28 0x1D 0xAC 0x05
+//0.753V
+i2cset -f -y 14 0x20 0x00 0
+i2ctransfer -f -y 14 w3@0x20 0x21 0x2D 0x01