feat(ttl): Add the Diag / SONiC BER cycle macro
6_Blanton_Script_BER_Cycle.ttl is a standalone macro, not part of A/B/C.
Each cycle measures PRBS BER on unit 0 in the Diag OS, cold-boots into
SONiC by writing the CB FPGA, measures again, and cold-boots back; while
1, no end. The boot target is chosen in the BIOS Boot Manager ("USB
Device" = Diag, "Hard Drive" = SONiC) and confirmed by the boot
signature. The log goes to Logs\Blanton_BER_Cycle_<ts>.log.
prbsstat runs with Interval=30 and the BER is read after sleep 40. The
sleep has to be longer than the interval: checked against the error
counts 'prbs get' reports in the same cycle, sleep 10 read Diag ~60x and
SONiC ~40x low, and sleep 30 still read Diag ~60x low because its Ber is
sent 30.15 s after STArt, before the first interval is published.
Interval=30 + sleep 40 matched on both sides over 73 cycles.
Known limits: the SONiC -> Diag boot writes a hard-coded BDF
(0000:05:00.0); the prompts assume the hostname 'sonic'; the fan is set
to 30 % on the SONiC side only; the password is the placeholder.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UniUXkxgCG2Ty74advL8Pd
This commit is contained in:
Claude Opus 5.5
@@ -0,0 +1,315 @@
|
||||
;================================================================
|
||||
; Prompt Definitions
|
||||
;================================================================
|
||||
prompt_login = "sonic login:"
|
||||
prompt_sonic = "admin@sonic:~$"
|
||||
prompt_sonic_root = "root@sonic:~#"
|
||||
prompt_diag = "root@(none):~#"
|
||||
|
||||
; ============================================================
|
||||
; [1] Config
|
||||
; ============================================================
|
||||
SWB_UNIT0 = 1 ; 1 = this DUT has switch unit 0, wait for it ; 0 = skip
|
||||
SWB_UNIT1 = 1 ; 1 = this DUT has switch unit 1, wait for it ; 0 = skip
|
||||
|
||||
bb_post_hotkey = 'Post Code>>:0226' ; 看到此 POST code 後開始送 ESC
|
||||
bb_esc_ack = 'Esc is pressed' ; BIOS 收到 ESC 的回應訊息
|
||||
bb_fp_continue = 'continue to booting' ; Front Page：Continue 反白時的說明欄（同一 row 內的字串）
|
||||
bb_fp_bootmgr = 'you to the Boot Manager' ; Front Page：Boot Manager 反白時的說明欄
|
||||
bb_bm_header = 'EFI Boot Devices' ; Boot Manager 清單標題
|
||||
bb_bm_footer = 'ESC to exit' ; Boot Manager 頁面最後一段文字（畫完判定）
|
||||
|
||||
bb_key_esc = #27
|
||||
bb_key_down = #27'[B'
|
||||
bb_key_enter = #13
|
||||
|
||||
;diag_tok = 'KINGSHARKS' ; EFI USB Device (KINGSHARKS-ANTU04)
|
||||
;sonic_tok = 'J983670007' ; EFI Hard Drive (J983670007-TS2TMTE712P-VS2)
|
||||
diag_tok = 'USB Device' ; EFI USB Device (KINGSHARKS-ANTU04)
|
||||
sonic_tok = 'Hard Drive' ; EFI Hard Drive (J983670007-TS2TMTE712P-VS2)
|
||||
|
||||
|
||||
diag_sig = 'ast1813b_diag' ; EFI Shell 執行 startup.nsh 載入的 diag kernel
|
||||
sonic_sig = 'SONiC-OS' ; SONiC GRUB entry 名稱（請依實際 GRUB 畫面確認）
|
||||
|
||||
gettime str_starttime "%Y%m%d-%H%M%S"
|
||||
getdir mdir
|
||||
sprintf2 filename '%s\Logs\%s_%s_%s.log' mdir "Blanton" "BER_Cycle" str_starttime
|
||||
; logopen <file> <binary> <append> <PlainText> <timestamp>
|
||||
; binary=0 text mode, so PlainText / timestamp are honoured
|
||||
; append=1 keep earlier cycles, do not overwrite
|
||||
; PlainText=1 strip the ANSI colour codes SONiC emits
|
||||
logopen filename 0 1 1 1
|
||||
|
||||
test_cycle = 0
|
||||
|
||||
while 1
|
||||
test_cycle = test_cycle + 1
|
||||
flushrecv
|
||||
logwrite ''#13#10
|
||||
sprintf2 log_cycle_msg 'BER Diag/SONiC Cycle Test : %d'#13#10 test_cycle
|
||||
logwrite '#####################################'#13#10
|
||||
logwrite log_cycle_msg
|
||||
logwrite '#####################################'#13#10
|
||||
settitle log_cycle_msg
|
||||
; ============================================================
|
||||
; [2] Call : Script where switching is needed
|
||||
; ============================================================
|
||||
; ====== Diag Test ======
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=3"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STArt Interval=30"'
|
||||
wait prompt_diag
|
||||
sendln "sleep 40"
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat Ber"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STOp"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs clear"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 256-259 dsc"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:show temp'
|
||||
wait prompt_diag
|
||||
sendln "swutil *:extphy core_diag all"
|
||||
wait prompt_diag
|
||||
|
||||
; ---- Diag -> SONiC ----
|
||||
sendln 'fpga_switch.sh cb 0 0x480 0xD0000'
|
||||
bb_target_tok = sonic_tok
|
||||
bb_sig_target = sonic_sig
|
||||
bb_sig_other = diag_sig
|
||||
call bb_boot_to
|
||||
if bb_ok = 0 then
|
||||
sprintf2 bb_msg 'Boot to SONiC failed: %s' bb_err
|
||||
messagebox bb_msg 'bios_boot'
|
||||
end
|
||||
endif
|
||||
|
||||
; ========== SONiC Test ==========
|
||||
wait prompt_login
|
||||
sendln "admin"
|
||||
wait "Password:"
|
||||
sendln "YourPaSsWoRd"
|
||||
wait prompt_sonic
|
||||
sendln "sudo -i"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 10"
|
||||
|
||||
; ========== FAN SPEED ==========
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 18-0020 > /sys/bus/i2c/drivers/max31790/unbind"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep .5"
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 18-0020 > /sys/bus/i2c/drivers/max31790/bind"
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 25-0020 > /sys/bus/i2c/drivers/max31790/unbind"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep .5"
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 25-0020 > /sys/bus/i2c/drivers/max31790/bind"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sprintf2 fan_ctrl_cmd 'fan-speed-control.sh %d' 30
|
||||
sendln fan_ctrl_cmd
|
||||
|
||||
wait "Set all configured fan channels to"
|
||||
sendln "y"
|
||||
|
||||
; ========== Wait DUT Init ==========
|
||||
include "utils/wait_init.ttl"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=3' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STArt Interval=30' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 40"
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat Ber' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STOp' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs clear' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c "dsh -c ' 39 'phydiag 256-259 dsc' 39 '"'
|
||||
wait prompt_sonic_root
|
||||
sendln 'show plat temperature'
|
||||
|
||||
; ---- SONiC -> Diag ----
|
||||
wait prompt_sonic_root
|
||||
sendln 'pcimem /sys/bus/pci/devices/0000:05:00.0/resource0 0x480 w 0xD0000'
|
||||
bb_target_tok = diag_tok
|
||||
bb_sig_target = diag_sig
|
||||
bb_sig_other = sonic_sig
|
||||
call bb_boot_to
|
||||
if bb_ok = 0 then
|
||||
sprintf2 bb_msg 'Boot to Diag failed: %s' bb_err
|
||||
messagebox bb_msg 'bios_boot'
|
||||
end
|
||||
endif
|
||||
endwhile
|
||||
|
||||
logclose
|
||||
end
|
||||
|
||||
; ============================================================
|
||||
; [3] Subroutine
|
||||
; ============================================================
|
||||
:bb_boot_to
|
||||
bb_saved_to = timeout
|
||||
call bb_run
|
||||
timeout = bb_saved_to
|
||||
mtimeout = 0
|
||||
return
|
||||
|
||||
:bb_run
|
||||
bb_ok = 0
|
||||
bb_err = ''
|
||||
call bb_enter_bios
|
||||
if bb_ok = 0 return
|
||||
call bb_goto_bootmgr
|
||||
if bb_ok = 0 return
|
||||
call bb_find_idx
|
||||
if bb_ok = 0 return
|
||||
call bb_select
|
||||
call bb_verify
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; 等 POST 0226，之後連送 ESC 直到 BIOS 回應 'Esc is pressed'
|
||||
; ------------------------------------------------------------
|
||||
:bb_enter_bios
|
||||
bb_ok = 0
|
||||
flushrecv ; 清掉 reboot 前的舊資料，避免誤比對
|
||||
timeout = 300
|
||||
mtimeout = 0
|
||||
wait bb_post_hotkey
|
||||
if result = 0 then
|
||||
bb_err = 'timeout waiting POST code 0226'
|
||||
return
|
||||
endif
|
||||
|
||||
timeout = 0
|
||||
mtimeout = 300
|
||||
for bb_i 1 200 ; 300 ms x 200 = 最多約 60 秒
|
||||
send bb_key_esc
|
||||
wait bb_esc_ack
|
||||
if result > 0 then
|
||||
bb_ok = 1
|
||||
break ; 收到 ack 立即停送，避免多餘 ESC 把 Front Page 退掉
|
||||
endif
|
||||
next
|
||||
mtimeout = 0
|
||||
if bb_ok = 0 bb_err = 'no ESC ack from BIOS'
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; Front Page：預設反白在 Continue，按一次 Down 到 Boot Manager
|
||||
; 以右側說明欄文字確認反白位置，再按 Enter
|
||||
; ------------------------------------------------------------
|
||||
:bb_goto_bootmgr
|
||||
bb_ok = 0
|
||||
timeout = 30
|
||||
wait bb_fp_continue
|
||||
if result = 0 then
|
||||
bb_err = 'Front Page not shown'
|
||||
return
|
||||
endif
|
||||
|
||||
mpause 500
|
||||
send bb_key_down
|
||||
timeout = 5
|
||||
wait bb_fp_bootmgr
|
||||
if result = 0 then
|
||||
bb_err = 'cannot highlight Boot Manager'
|
||||
return
|
||||
endif
|
||||
|
||||
mpause 300
|
||||
send bb_key_enter
|
||||
timeout = 15
|
||||
wait bb_bm_header
|
||||
if result = 0 then
|
||||
bb_err = 'Boot Manager page not shown'
|
||||
return
|
||||
endif
|
||||
bb_ok = 1
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; 解析 Boot Manager 清單，計算目標 entry 的 index（0-based）
|
||||
; 每個 entry 以 'EFI '（含 UEFI）或 'SVOS' 開頭計數，命中目標字串即停止
|
||||
; ------------------------------------------------------------
|
||||
:bb_find_idx
|
||||
bb_ok = 0
|
||||
bb_idx = -1
|
||||
bb_cnt = 0
|
||||
timeout = 0
|
||||
mtimeout = 3000
|
||||
for bb_i 1 20
|
||||
wait 'EFI ' 'SVOS' bb_target_tok
|
||||
if result = 0 break ; 清單畫完仍未命中
|
||||
if result = 3 then
|
||||
bb_idx = bb_cnt - 1 ; 目標字串前的 'EFI ' 屬於目標 entry 本身
|
||||
break
|
||||
endif
|
||||
bb_cnt = bb_cnt + 1
|
||||
next
|
||||
mtimeout = 0
|
||||
|
||||
if bb_idx < 0 then
|
||||
bb_err = 'target entry not found in Boot Manager'
|
||||
return
|
||||
endif
|
||||
|
||||
timeout = 5
|
||||
wait bb_bm_footer ; 等整頁畫完才開始按鍵
|
||||
bb_ok = 1
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; 預設反白在第一個 entry，往下移 bb_idx 格後按 Enter
|
||||
; ------------------------------------------------------------
|
||||
:bb_select
|
||||
mpause 300
|
||||
if bb_idx > 0 then ; TTL 的 for 1 0 會倒數執行，必須先擋掉
|
||||
for bb_i 1 bb_idx
|
||||
send bb_key_down
|
||||
timeout = 3
|
||||
wait bb_bm_footer ; BIOS 每按一次會整頁重畫，畫完再按下一次
|
||||
mpause 200
|
||||
next
|
||||
endif
|
||||
send bb_key_enter
|
||||
; 之後不可再送任何按鍵：Diag 走 EFI Shell，
|
||||
; 任何按鍵都會被當成「跳過 / 中斷 startup.nsh」
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; 同時等目標與另一個 image 的特徵字串
|
||||
; ------------------------------------------------------------
|
||||
:bb_verify
|
||||
bb_ok = 0
|
||||
timeout = 300
|
||||
wait bb_sig_target bb_sig_other
|
||||
if result = 1 then
|
||||
bb_ok = 1
|
||||
elseif result = 2 then
|
||||
bb_err = 'booted into wrong image'
|
||||
else
|
||||
bb_err = 'timeout waiting boot signature'
|
||||
endif
|
||||
return
|
||||
Reference in New Issue
Block a user