Compare commits
11
Commits
V1.2.3
...
738f1dd1c6
| Author | SHA1 | Date | |
|---|---|---|---|
  etwenandClaude Opus 5.5
|
738f1dd1c6 | ||
|
etwenandClaude Opus 5.5
|
0407bbe04f | ||
|
etwenandClaude Opus 5.5
|
319ee07de3 | ||
|
etwenandClaude Opus 5.5
|
16da1c68f2 | ||
|
etwenandClaude Opus 5.5
|
f378340f41 | ||
|
etwenandClaude Opus 5.5
|
fd2282d34b | ||
|
etwenandClaude Opus 5.5
|
aed2be66b2 | ||
|
etwenandClaude Opus 5.5
|
b652ec8072 | ||
|
etwenandClaude Opus 5.5
|
4db9b45ce7 | ||
|
etwenandClaude Opus 5.5
|
7937ade30e | ||
|
etwenandClaude Opus 5.5
|
ebb2260798 |
+11
-4
@@ -161,7 +161,9 @@ Blanton_TTL_Script/
|
||||
└── Script_ABC_Blanton/ # ← Tera Term 的工作目錄（整包給測試員）
|
||||
│
|
||||
├── 4_Blanton_Script_thermal_safety.ttl # 熱 / 安規：獨立跑，不接 A→B→C
|
||||
├── 5_Blanton_Script_Reboot_Cycle.ttl # 重開機循環：獨立跑，while 1 無止境（未上機驗證）
|
||||
├── 5_Blanton_Script_Boot_Cycle.ttl # 開機循環（warm / cold，EN_Cold_Warm_boot）：獨立跑，while 1 無止境
|
||||
├── 5_1_Blanton_Script_Boot_Cycle_Fast.ttl # 同 Script 5，但 Check Pt8 只跑 traffic ps（不打流量），循環較短
|
||||
├── 6_Blanton_Script_BER_Cycle.ttl # Diag ↔ SONiC 冷開機循環，兩邊各量一次 unit 0 BER：獨立跑，while 1
|
||||
├── config.ttl # 全域設定：testcase 名、EN_Margin / EN_TX_FIR / EN_log / EN_timestamp、
|
||||
│ # 風扇與 SWB 宣告、SSD/USB/BMC_USB 壓力秒數、三個 prompt 字串
|
||||
├── hammer/ # 🚫 gitignored — mlucas ELF binary（~99 MB），DUT image 自帶，
|
||||
@@ -204,6 +206,8 @@ Blanton_TTL_Script/
|
||||
│ # ⚠️ V1.1.9 起 A/B/C 內註解掉的呼叫已整段刪除，只剩手動執行
|
||||
├── blanton_ber.sh # 全機 SerDes BER 掃描（phydiag prbs / prbsstat）
|
||||
│ # V1.2.2 起含 port 268（100G ce0），summary 每 unit 分 200G/100G/TOTAL
|
||||
├── blanton_ber_debug.sh # BER 原始輸出（p=p31、sleep 40、-u 0|1），不判定
|
||||
├── blanton_fdr.sh # FDR 統計（phydiag fdrstat start/clear/Counters/STOp），A/B/C 夾住流量
|
||||
├── bcm_100g_dsc_cycle.sh # 100G link down/up 循環 + 每輪 DSC 與 retimer TX/RX 讀回（未驗證）
|
||||
├── bcm_dsc_scan.sh # 全機 SerDes DSC dump（phydiag <port> dsc，~445 port × 2 unit）
|
||||
│ # 由 EN_TX_FIR 控制，A 與 C 各掃一次；單次約 10 分鐘
|
||||
@@ -215,10 +219,13 @@ Blanton_TTL_Script/
|
||||
├── blanton_tr518.sh # TR518 封包測試，量功耗前的負載來源
|
||||
├── TH6_SWB0_power_readback.sh # SWB0 19 條軌 V×I + 總功耗
|
||||
├── TH6_SWB1_power_readback.sh # SWB1 同上
|
||||
│ # ⚠️ 已納入交付，但 A/B/C 的呼叫仍註解掉（bring-up 中）
|
||||
│ # V1.2.5 起由 utils/setup_pmon.ttl 呼叫，每個 PMON 快照都有
|
||||
├── ddr5_temp.sh # DDR5 DIMM 溫度（SPD5118 @ i2c-5 0x50/0x51，reg 0x31）
|
||||
├── hsc_temp_readback.sh # LTC4287 HSC 溫度（i2c-28 0x40/0x45，內/外部感溫）
|
||||
├── avt_pmpower.sh # AMD CPU 封裝功耗（AVTCMD pmm get_pmdata；AVT 是 NDA，不隨包）
|
||||
├── tray_id_stress.sh # Tray ID I2C stress（bus 34/35/38/39 0x70 reg 0x02，寫 0xA5/0x5A 讀回）
|
||||
├── retimer_lanes.sh # 單顆 Agera3 retimer 的 lane TX off/on/status（sys + line side）
|
||||
├── unused_lanes.sh # 依內建表把沒接線的 retimer lane / TH6 port 關掉（呼叫 retimer_lanes.sh）
|
||||
├── usb_target.sh # 偵測 USB 裝置節點／掛載點（排除系統碟）
|
||||
├── bmc_monitor.sh # BMC 監控：free -m + I2C 寫入/讀回圖樣測試
|
||||
├── bmc_monitor_ddr.sh # ⚠️ 已停用：V1.1.9 起 B/C 內的註解區塊已刪除，DDR 壓力走 bgctl + bmc-manager
|
||||
@@ -381,7 +388,7 @@ PROFILE_CHANNELS=( "0:high:8" "1:low:8" ... ) # "channel:operation:change_perc
|
||||
|
||||
| 模組 | 進入點 | 功能 |
|
||||
|------|--------|------|
|
||||
| **Script A（Pre-test）** | `1_Blanton_Script_A.ttl` V1.2.3 | root 登入 → `date -s` 對時 → 清 job log → **收掉前一輪殘留**（`hw-test-session finish` → `bgctl reset --yes` → `bgctl stop --all` → `bgctl list` 確認清空）→ `hw-test-session start` → **設定風扇轉速** → **等資料面就緒**（`wait_init.ttl`）→ DUT 清單（boot/version/fwutil/syseeprom/ssdhealth/TPM/NVMe）→ BMC enroll + version/status → source bash 工具 → 清/讀 7 組 PCIe AER + `ras-mc-ctl --summary` → `lspci` → margin → PMON → dmesg → **10G/1G 管理網路 ping** → **NFC 基線**（start → 30s → stop → report）→ 100G uplink 設定與狀態 → **BER 基線掃描**（依 `SWB_UNIT`，V1.2.1 新增）→ **一輪流量基線** → **SerDes DSC 基線**（`EN_TX_FIR`）→ `show uptime` |
|
||||
| **Script A（Pre-test）** | `1_Blanton_Script_A.ttl` V1.2.6 | root 登入 → `date -s` 對時 → 清 job log → **收掉前一輪殘留**（`hw-test-session finish` → `bgctl reset --yes` → `bgctl stop --all` → `bgctl list` 確認清空）→ `hw-test-session start` → **設定風扇轉速** → **等資料面就緒**（`wait_init.ttl`）→ DUT 清單（boot/version/fwutil/syseeprom/ssdhealth/TPM/NVMe）→ BMC enroll + version/status → source bash 工具 → 清/讀 7 組 PCIe AER + `ras-mc-ctl --summary` → `lspci` → margin → PMON → dmesg → **10G/1G 管理網路 ping** → **NFC 基線**（start → 30s → stop → report）→ 100G uplink 設定與狀態 → **`unused_lanes.sh off`**（V1.2.6）→ **BER 基線掃描**（依 `SWB_UNIT`，V1.2.1 新增）→ **一輪流量基線**（V1.2.6 起兩 unit 時夾 FDR，sleep 40） → **SerDes DSC 基線**（`EN_TX_FIR`）→ `show uptime` |
|
||||
| **Script B（Stress）** | `2_Blanton_Script_B.ttl` | **V1.1.8 起 `mlucas-avx2 -cpu 0:15` 由 `systemd-run --unit=mlucas-amm`（`Type=exec`、`Restart=always`）啟動，不再是 shell 的 `&` 背景 job** + `bgctl run` 的 `memtester` / SSD / USB 壓力（v1.1.7 起 SSD/USB 的 `--runtime`/`--passes` 讀 `config.ttl` 的 `SSD_RUNTIME`/`SSD_COUNT`、`USB_RUNTIME`/`USB_COUNT`；BMC memtester 不帶次數 = 跑到被停） + BMC DDR（`bmc-manager run memtester`）→ BMC USB net test（探測 cdc_ncm 介面，`systemd-run` 掛 `BMC_USB_RUNTIME` 秒的 ping，V1.1.8 前寫死 4 小時）→ 啟動 mgmt ping 監控 → **啟動 NFC 輪詢** → `jobs` / `systemctl is-active mlucas-amm` / `bgctl list` → traffic（依 `SWB_UNIT`）→ `while 1` 每輪 PMON + `bgctl list`/`jobs`/`systemctl is-active mlucas-amm` + `sleep 60`（**V1.1.4 起 margin 不在迴圈內**；V1.2.0 起等待走 DUT 端 `sleep` 而非 macro 端 `pause`）|
|
||||
| **Script C（Post-test）** | `3_Blanton_Script_C.ttl` | `kill $(jobs -p)` + **`systemctl stop mlucas-amm`**（systemd unit 不是 shell job，`jobs -p` 抓不到）+ `bgctl stop --all` / `reset` + 停 BMC USB unit、mgmt ping 與 **NFC 輪詢** → PMON + dmesg → 7 組 AER + `ras-mc-ctl` → BMC USB `journalctl` **寫進 `log/bmc_usb_net.log`**（不再印在 console） → `ip -s link show eth0/eth1` → `cat` mlucas log（並 `cp` 進 job 目錄一起帶走）→ **NFC `report`** → traffic `stop` + `report` → **SerDes DSC 收尾**（`EN_TX_FIR`）→ **BER 掃描**（依 `SWB_UNIT`）→ NVMe 健康 → `show reboot-cause` → **margin 掃描**（`EN_Margin`，V1.1.4 由 Script B 移來）→ `uptime` → **job log 複製到 USB（帶時戳）** → `exit` + wait『Script done』→ `hw-test-session finish` |
|
||||
| **Script 4（Thermal / Safety）** | `4_Blanton_Script_thermal_safety.ttl` | **獨立腳本，不接 A→B→C。** Script A 式的環境建立（登入 / session / 風扇 / `wait_init` / DUT 清單 / BMC / PCIe 清除 / `pcie_bus` / PMON / dmesg）→ **滿載**（`mlucas-avx2 -cpu 0:15`，V1.1.8 起與 Script B 同樣掛成 `mlucas-amm` systemd unit + `blanton_tr518.sh start`）→ `while 1`：PMON + `TH6_SWB0/1_power_readback.sh` + `avt_pmpower.sh`（CPU 封裝功耗，V1.2.3）+ `bgctl list` / `jobs` / `systemctl is-active mlucas-amm`，`pause 60`。**沒有收尾段** —— 中斷後 DUT 仍在 `port cd lb=mac` / `l2 learn off` / `test mode nr=yes`，且 CPU 仍滿載，要手動 `blanton_tr518.sh stop` + `systemctl stop mlucas-amm` |
|
||||
@@ -812,7 +819,7 @@ margin status、全部 VRM 軌的 Vin/Vout/Iout/Temp、CB + ICB 溫感讀值，
|
||||
- [ ] `CHANGELOG.md`：延續三支腳本頂端的 Version History，集中成一份
|
||||
- [ ] 三支腳本的 header 版號與 `CHANGELOG.md` 對齊，`config.ttl` 加 `script_version` 並寫進 log 開頭
|
||||
- [ ] `docs/TTL_Script_Blanton_Status_*.xlsx` 更新為全 OK，或把剩餘項目移進 Future Extensions
|
||||
- [x] 打 git tag，push `nas` + `gitea`（已至 `V1.2.3`；`publish/` 依 Script A 檔頭版號打包）
|
||||
- [x] 打 git tag，push `nas` + `gitea`（已至 `V1.2.6`；`publish/` 依 Script A 檔頭版號打包）
|
||||
|
||||
**驗收條件：** 從 zip 解壓到一台乾淨的測試 NB，照 README 操作，不看原始碼就能完成一輪 A→B→C
|
||||
並產出 summary；`publish/` 內容與 git tag 一致。
|
||||
|
||||
@@ -9,7 +9,7 @@ DUT 端的取數能力由一組 **bash 工具庫** 提供（CB FPGA `pcimem` →
|
||||
|
||||
完整架構見 [ARCHITECTURE.md](ARCHITECTURE.md)。
|
||||
|
||||
**目前狀態（2026-09-23）**：Script A 為 **V1.2.3**（A 集中記錄所有 TTL 的變更）。涵蓋
|
||||
**目前狀態（2026-10-21）**：Script A 為 **V1.2.6**（A 集中記錄所有 TTL 的變更）。涵蓋
|
||||
PCIe AER / DDR EDAC / PMON+TPM / 電壓 margin（9 顆 LTC2980）/ SWB loopback 線速流量 /
|
||||
10G+1G 管理網路 ping / BMC DDR 與 USB / NVMe 健康，壓力層走平台的 `bgctl`。
|
||||
switch unit 數量由 `config.ttl` 的 `SWB_UNIT0` / `SWB_UNIT1` 宣告，風扇轉速由 `FAN_SPEED` 指定
|
||||
@@ -36,11 +36,21 @@ NFC tag 讀取由 `nfc_polling.sh` 背景輪詢（A 做基線、B 起、C 停並
|
||||
取 PMON + 兩片 SWB 的軌功耗 + **AMD CPU 封裝功耗**（`avt_pmpower.sh`，V1.2.3）；**沒有收尾段**，中斷後要手動 `blanton_tr518.sh stop`）。
|
||||
**V1.2.3 起 PMON 快照（`utils/setup_pmon.ttl`）多了 DDR5 DIMM 溫度（`ddr5_temp.sh`）與 LTC4287 HSC 溫度
|
||||
（`hsc_temp_readback.sh`）**，A/B/C/4/5 全部吃到；HSC 那支每次約 +4 秒。
|
||||
**V1.2.4 新增 Tray ID I2C stress（`tray_id_stress.sh`）**：Script A 跑一次當基線、Script B 每輪 soak 跑一次。
|
||||
另新增 **`6_Blanton_Script_BER_Cycle.ttl`**（Diag ↔ SONiC 冷開機循環量 BER，**獨立跑不接 A→B→C**），
|
||||
操作與分析見 `tmp/BER_Test_Cycle/runbook.md`（tmp 不進 git）。
|
||||
**V1.2.5 起 PMON 快照也帶兩片 SWB 的軌功耗**（`TH6_SWB{0,1}_power_readback.sh` 搬進 `setup_pmon.ttl`），
|
||||
⚠️ Script 4 迴圈原本就自己讀一次，現在**每輪讀兩次**。V1.2.5 另有 `blanton_ber_debug.sh`（BER 原始輸出、`p=p31`、`sleep 40`）、
|
||||
`retimer_lanes.sh` / `unused_lanes.sh`（把沒接線的 retimer lane / TH6 port 關 TX），以及
|
||||
`5_1_Blanton_Script_Boot_Cycle_Fast.ttl`（Script 5 拿掉流量那段，只留 `ps`）。
|
||||
**V1.2.6 起 FDR 統計（`blanton_fdr.sh`，`phydiag fdrstat`）接進流量**：A 包住流量基線（sleep 15→40）、
|
||||
B 在 soak 前 start、C 收尾 rdcnt + stop，**只在兩個 unit 都開時才跑**。Script A 另在 BER 前先 `unused_lanes.sh off`，
|
||||
⚠️ **沒有任何地方再 `on` 回來**。
|
||||
以及 **`5_Blanton_Script_Boot_Cycle.ttl`**（重開機循環，**獨立跑不接 A→B→C**：登入 → 風扇 →
|
||||
Check Pt1~Pt13 → `reboot` → `wait "Booting in blind mode"`，`cnt_cycle` 每輪遞增，`while 1` 無止境，
|
||||
要停就關 Tera Term 的 macro）。**尚未上機驗證**。
|
||||
流程圖：`docs/Blanton_Test_Flow.drawio`。
|
||||
最後一次發布是 **V1.2.3**；SWB 的 I2C 通道與位址已於 2026-08-19 上機驗證。
|
||||
最後一次發布是 **V1.2.6**；SWB 的 I2C 通道與位址已於 2026-08-19 上機驗證。
|
||||
margin 的 `VNOM` 已於 2026-08-30 改為 Blanton 實測中位數（144 條軌中 86 條上調 0.8~2.5%）。
|
||||
交付用 `./publish/publish.sh` 打包。
|
||||
|
||||
@@ -140,6 +150,12 @@ bash ~/Blanton_Script/port_prbs_monitor.sh stop # 收尾會跑 prbsstat
|
||||
# ⚠️ AVT 是 NDA，不在交付包裡：DUT 上要先解壓到 ~/AVT_Linux_NDA_2.8.37/，沒有就每輪 exit 2
|
||||
# ⚠️ 數值是 SMU telemetry 不是量測，要準就對照 VR 的 PMBus READ_POUT
|
||||
|
||||
# ── Tray ID I2C stress（V1.2.4，Script A / B 已接）────
|
||||
~/Blanton_Script/tray_id_stress.sh # bus 34/35/38/39，0x70 reg 0x02：寫 0xA5/0x5A 讀回比對 → Summary
|
||||
~/Blanton_Script/tray_id_stress.sh -n 100 # 重複 100 輪
|
||||
~/Blanton_Script/tray_id_stress.sh -R # 跑完不還原（預設會寫回原值並讀回確認）
|
||||
# exit 0 = 全 PASS、1 = 有 FAIL（讀回不符）或 ERROR（i2cset/i2cget 本身失敗）、2 = 參數錯
|
||||
|
||||
# ── PDB / CPB power brick 讀值 ──────────────────────
|
||||
./Blanton_Script/pwr_brick.sh show # Vin/Iin/Vout/Iout/Temp × 5 顆
|
||||
./Blanton_Script/pwr_brick.sh show -r # 多印 raw word
|
||||
@@ -169,6 +185,27 @@ sleep 30 # 至少等一個 interval 再 rep
|
||||
# -u 0 / -u 1 單邊；-c 1e-9 換門檻；-F 只列失敗；-f <log> 離線重解
|
||||
# ⚠️ 不能跟 blanton_traffic_linespeed / blanton_tr518 同時跑（都會接管同一批 port）
|
||||
|
||||
# ── BER 原始輸出（V1.2.5，不判定、不 summary，TTL 未接）──
|
||||
./Blanton_Script/blanton_ber_debug.sh # unit 0+1：set p=p31 → get×2 → STArt 30 → sleep 40 → Ber → STOp → clear
|
||||
./Blanton_Script/blanton_ber_debug.sh -u 0 # 單一 unit
|
||||
# 清單同 tools/BER_Test.txt，不含 268；BER_PORTS="...,268" 可加
|
||||
# ⚠️ 這支是 p=p31（已上機驗證），blanton_ber.sh 仍是 p=3 —— 兩者量的碼型可能不同
|
||||
|
||||
# ── FDR 統計（V1.2.6，A/B/C 已接，只在 SWB_UNIT0=SWB_UNIT1=1）──
|
||||
~/Blanton_Script/blanton_fdr.sh start # fdrstat STArt bin_group=both Interval=30，unit 0 → 1
|
||||
~/Blanton_Script/blanton_fdr.sh clear # fdrstat clear
|
||||
~/Blanton_Script/blanton_fdr.sh rdcnt # fdrstat Counters（Interval 結算後才讀，A 用 sleep 40）
|
||||
~/Blanton_Script/blanton_fdr.sh stop # fdrstat STOp ⚠️ 關鍵字是類推的，未上機驗證
|
||||
# -u 0|1 單邊；-i <sec> 改 Interval；-n dry-run。ports 預設 '1-259,270-565'（FDR_PORTS 可改）
|
||||
|
||||
# ── 沒接線的 retimer lane / TH6 port 關 TX（V1.2.5；V1.2.6 起 Script A 會 off，沒人 on 回來）──
|
||||
./Blanton_Script/unused_lanes.sh status # 兩 unit 全部列出 rx_lock / tx_off
|
||||
./Blanton_Script/unused_lanes.sh off [--asic 0] [--th6] # 預設 TX squelch；--th6 連 retimer 後面的 TH6 port 一起關
|
||||
./Blanton_Script/unused_lanes.sh on
|
||||
./Blanton_Script/retimer_lanes.sh 0 0x102 0xff status # 單顆 retimer：<asic> <addr> <lane_map> <off|on|status>
|
||||
# ⚠️ lane 有 RX lock（有訊號進來）時 off 會被拒絕（exit 2），--force 才會硬關
|
||||
# ⚠️ unused_lanes.sh 會檢查同目錄的 retimer_lanes.sh 有沒有 exec bit —— 兩支都要 chmod +x
|
||||
|
||||
# ── SerDes DSC 擷取（TX_FIR / RXFFE / DFE / EYE / SNR）──
|
||||
./Blanton_Script/bcm_dsc_scan.sh # unit 0+1 全掃，約 10 分鐘
|
||||
./Blanton_Script/bcm_dsc_scan.sh -u 0 # 只掃一個 unit（時間減半）
|
||||
@@ -357,6 +394,11 @@ Tera Term 連 COM port (115200-8-N-1)
|
||||
- ⚠️ **`stress_hhmd.py` / `stress_pcie.py` 已於 2026-08-17 由 KC 移除**（Status 表 ScriptB #5/#7）。
|
||||
Script B 現在是 **8 個背景 job**（1 mlucas + 5 mem + ssd + usb），不是 10 個。
|
||||
I2C／PCIe 的持續讀取壓力目前沒有替代品。
|
||||
- ⚠️ **`prbsstat Ber` 要等第一個 interval 結算之後才讀：sleep 必須「大於」Interval**（2026-09-30 驗證）。
|
||||
`6_Blanton_Script_BER_Cycle.ttl` 用 `Interval=30` + `sleep 40`。拿同一輪 `prbs get` 的錯誤數交叉比對：sleep 10 時 Diag 低 ~60×、
|
||||
SONiC 低 ~40×；sleep 30（= Interval）時 Diag 仍低 ~60×（Ber 在 STArt 後 30.15 s 送出，剛好在結算前）。
|
||||
⚠️ **Script A / C 的 BER 也是 `blanton_ber.sh start`（Interval=30）→ TTL `sleep 30` → `report`**，跑在 SONiC 上 —— 正是「sleep = Interval」的邊界情況，
|
||||
能不能趕上第一個 interval 結算**未驗證**。建議改成 `sleep 40`（或 `BER_INTERVAL` 調小），並用 `validate_prbsget.py` 的方法驗證一次
|
||||
- ⚠️ **`pause` 是停 macro，`sleep` 是停 DUT**（V1.2.0 起 A/B/C 一律用後者）：`pause N` 期間 macro 不理會
|
||||
DUT，shell 是閒著的，等於用猜的估上一個指令跑多久；`sendln "sleep N"` + `wait prompt_sonic_root`
|
||||
把等待放到 DUT 上，prompt 回來才繼續，兩邊不會走散，而且這一段會帶時戳進 log。
|
||||
|
||||
@@ -0,0 +1,54 @@
|
||||
# v1.2.4 — Tray ID I2C stress in Script A and B, and a Diag / SONiC BER cycle that reads the BER correctly
|
||||
|
||||
## ✨ New features
|
||||
|
||||
**`tray_id_stress.sh` — Tray ID I2C write / read-back stress**
|
||||
* Buses `34` / `35` / `38` / `39`, device `0x70`, register `0x02`. Each bus gets `0xA5` written and read back, then `0x5A` written and read back — the two patterns put every bit in both states.
|
||||
* One line per step (`PASS` / `FAIL` / `ERROR`), then a per-bus **Summary** table and a single `Tray ID stress RESULT: PASS|FAIL` line. Exit `0` = all PASS, `1` = any FAIL or I2C error, `2` = bad arguments.
|
||||
* `FAIL` (the read worked but returned the wrong value) and `ERROR` (`i2cset` / `i2cget` itself failed) are counted separately, because they point at different faults.
|
||||
* The original register value is read first and **written back at the end**, verified by a read. `-R` skips that; `-n N` repeats the whole sequence N times. Buses, address, register and patterns are editable at the top of the file.
|
||||
|
||||
**Script A and Script B run it**
|
||||
* **Script A** runs one pass after `show_dmesg` as the baseline.
|
||||
* **Script B** runs one pass in every soak round, before `sleep 60` — 12 writes per round, registers restored each time.
|
||||
|
||||
**`6_Blanton_Script_BER_Cycle.ttl` — Diag ↔ SONiC BER cycle (standalone)**
|
||||
* Each cycle measures PRBS BER on unit 0 in the Diag OS, cold-boots into SONiC, measures again, and cold-boots back to Diag. `while 1`, no end. The boot target is picked in the BIOS Boot Manager (`USB Device` = Diag, `Hard Drive` = SONiC).
|
||||
* Log: `Logs\Blanton_BER_Cycle_<ts>.log`, timestamps always on.
|
||||
|
||||
## 🐛 Bug fixes
|
||||
|
||||
**`prbsstat Ber` was read before the first interval had been published — BER read 40–60× low**
|
||||
* The BER cycle originally read `prbsstat Ber` 10 s after `prbsstat STArt Interval=30`. Checked against the error counts that `prbs get` reports in the same cycle, that read **Diag ~60× low and SONiC ~40× low**.
|
||||
* Moving to `sleep 30` (equal to the interval) fixed SONiC but **not Diag**: its `Ber` goes out 30.15 s after `STArt`, just before the first interval is published. SONiC's `bcmcmd` adds ~0.3 s and just makes it.
|
||||
* The macro now uses **`Interval=30` + `sleep 40`**. Over 73 cycles both sides agree with the `prbs get` estimate to within 0.1 decade. The rule: **the sleep must be longer than the interval.**
|
||||
|
||||
## 📦 Downloads
|
||||
|
||||
| File | Contents |
|
||||
|---|---|
|
||||
| `Script_ABC_Blanton_V1.2.4.zip` | The full Tera Term working directory, including `Blanton_Script/` to copy onto the DUT |
|
||||
|
||||
```bash
|
||||
chmod +x ~/Blanton_Script/*.sh
|
||||
grep -rlU $'\r' ~/Blanton_Script # expect no output
|
||||
```
|
||||
|
||||
## ⚠️ Before you run
|
||||
|
||||
* **`chmod +x` after deploying.** Script A and B call `tray_id_stress.sh` by path; without the exec bit every call is `Permission denied` and the round carries on without the check.
|
||||
* **Any BER log taken before 2026-09-30 14:13 reads 40–60× low** (BER cycle with `sleep ≤ Interval`). Relative Diag-vs-SONiC trends are usable; absolute values are not.
|
||||
* **Script A / C's BER is the same edge case**: `blanton_ber.sh start` (Interval=30) → `sleep 30` → `report`, on SONiC. Whether it catches the first interval has **not been verified**. Lengthening that sleep to 40 is the safe change.
|
||||
* **The BER cycle's SONiC → Diag boot writes a hard-coded BDF** (`pcimem /sys/bus/pci/devices/0000:05:00.0/resource0 0x480`). Check the CB FPGA BDF on every unit before running it.
|
||||
* **The BER cycle expects the hostname `sonic`.** A unit with another hostname (e.g. `Margin02`) needs `prompt_sonic` / `prompt_sonic_root` edited, or the macro waits forever.
|
||||
* **The BER cycle sets the fan to 30 % on the SONiC side only** — SONiC runs ~11 °C hotter than Diag, a variable in any Diag-vs-SONiC comparison.
|
||||
* **Its SONiC password is the `YourPaSsWoRd` placeholder**, and it does not read `config.ttl` or `secret/`.
|
||||
* **Script 4 has no teardown**: finish it with `blanton_tr518.sh stop` **and** `systemctl stop mlucas-amm`.
|
||||
* **`FAN_SPEED` is 100.**
|
||||
|
||||
## 🔗 Links
|
||||
|
||||
* [ARCHITECTURE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/ARCHITECTURE.md) — test flow, data models, constraints
|
||||
* [CLAUDE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/CLAUDE.md) — commands and the bench gotchas
|
||||
|
||||
**Full changelog:** [V1.2.3...V1.2.4](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/compare/V1.2.3...V1.2.4)
|
||||
@@ -0,0 +1,56 @@
|
||||
# v1.2.5 — Switch-board rail power in every snapshot, a raw BER run, and tools to turn off unused lanes
|
||||
|
||||
## ✨ New features
|
||||
|
||||
**PMON snapshots now carry the switch-board rail power**
|
||||
* `utils/setup_pmon.ttl` calls `TH6_SWB0_power_readback.sh` and `TH6_SWB1_power_readback.sh` right after `show platform current` — the 19 rails of each switch board with V × I and a `TOTAL POWER` line.
|
||||
* `setup_pmon` is shared, so this lands in Script A, B, C, 4 and 5 alike.
|
||||
|
||||
**`blanton_ber_debug.sh` — the hand-run BER flow as one command**
|
||||
* Runs exactly what `tools/BER_Test.txt` does: `prbs set p=p31` → `prbs get` twice → `prbsstat STArt Interval=30` → `sleep 40` → `prbsstat Ber` → `STOp` → `prbs clear`.
|
||||
* Every `bcmcmd` output is printed **as is**, under a `### [time] unit N: ...` header — no parsing, no PASS/FAIL, no summary. For looking at the raw output on the bench; `blanton_ber.sh` remains the judged version.
|
||||
* `-u 0` / `-u 1` for one switch unit; both by default. `BER_POLY`, `BER_INTERVAL`, `BER_WAIT` and `BER_PORTS` can be overridden from the environment.
|
||||
|
||||
**`retimer_lanes.sh` / `unused_lanes.sh` — turn off TX on lanes nothing is cabled to**
|
||||
* `retimer_lanes.sh <asic> <addr> <lane_map> <off|on|status>` acts on one Agera3 retimer, sys **and** line side. `--method squelch` (default, TX squelch, lanes stay powered) or `--method power` (TX+RX power-down, needs an `agera3` that has the `power` command). It reads the state back afterwards and prints `PASS` / `FAIL`.
|
||||
* `unused_lanes.sh <off|on|status>` applies that to a built-in table — 14 retimer rows and one direct-TH6 row (TSC31, `cd112-cd115`) — on both switch boards. `--asic 0|1|all`, `--th6` to also disable the TH6 ports behind the retimer rows, `--only <target>` for a single row. Ends with `ok / refused / failed` counts.
|
||||
* **`off` is refused on a lane that receives a signal** (RX PMD lock, or link up on a TH6 port) unless `--force` is given.
|
||||
|
||||
**`5_1_Blanton_Script_Boot_Cycle_Fast.ttl` — the boot cycle without the traffic run (standalone)**
|
||||
* Identical to Script 5, except Check Pt8 only runs `blanton_traffic_linespeed ps` — no `init` / `start` / 15 s / `stop` / `report`. A shorter cycle when the point is the number of boots.
|
||||
|
||||
**Boot cycle shows its count in the window title**
|
||||
* Script 5 and 5_1 set the Tera Term title to `Reboot Cycle Test : n` or `Power Cycle Test : n` each round.
|
||||
|
||||
## 🐛 Bug fixes
|
||||
|
||||
**`qfx5252-stress-usb` now runs with `--force`** in Script B and in the boot cycles.
|
||||
|
||||
## 📦 Downloads
|
||||
|
||||
| File | Contents |
|
||||
|---|---|
|
||||
| `Script_ABC_Blanton_V1.2.5.zip` | The full Tera Term working directory, including `Blanton_Script/` to copy onto the DUT |
|
||||
|
||||
```bash
|
||||
chmod +x ~/Blanton_Script/*.sh
|
||||
grep -rlU $'\r' ~/Blanton_Script # expect no output
|
||||
```
|
||||
|
||||
## ⚠️ Before you run
|
||||
|
||||
* **`chmod +x` after deploying.** The power readbacks are called by path from every PMON snapshot, and `unused_lanes.sh` refuses to start unless `retimer_lanes.sh` next to it is executable.
|
||||
* **Script 4 now reads the switch-board power twice per round** — once inside `setup_pmon`, once from its own loop. Harmless, but the log carries both.
|
||||
* **`blanton_ber_debug.sh` uses `p=p31` (verified on the bench); `blanton_ber.sh`, and so Script A / C, still sets `p=3`.** The two may not be measuring the same pattern — do not compare their BER directly until that is settled.
|
||||
* **`blanton_ber_debug.sh` leaves out port 268**, the same list as `BER_Test.txt`. Add it with `BER_PORTS="...,268"`.
|
||||
* **`EN_Cold_Warm_boot = 0` (the `config.ttl` default) hangs Script 5 and 5_1.** Set it to `1` (reboot) or `2` (power cycle).
|
||||
* **Script 5 and 5_1 are two copies of the same macro** — a fix to one has to be made to the other.
|
||||
* **Script 4 has no teardown**: finish it with `blanton_tr518.sh stop` **and** `systemctl stop mlucas-amm`.
|
||||
* **`FAN_SPEED` is 100.**
|
||||
|
||||
## 🔗 Links
|
||||
|
||||
* [ARCHITECTURE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/ARCHITECTURE.md) — test flow, data models, constraints
|
||||
* [CLAUDE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/CLAUDE.md) — commands and the bench gotchas
|
||||
|
||||
**Full changelog:** [V1.2.4...V1.2.5](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/compare/V1.2.4...V1.2.5)
|
||||
@@ -0,0 +1,46 @@
|
||||
# v1.2.6 — FDR statistics around the traffic run, and unused lanes turned off before the baseline
|
||||
|
||||
## ✨ New features
|
||||
|
||||
**`blanton_fdr.sh` — FDR statistics through `phydiag fdrstat`**
|
||||
* Four sub-commands, each run on unit 0 then unit 1, over ports `'1-259,270-565'`:
|
||||
`start` (`fdrstat STArt bin_group=both Interval=30`), `clear` (`fdrstat clear`), `rdcnt` (`fdrstat Counters`), `stop` (`fdrstat STOp`).
|
||||
* Output is printed as is, under a `### [time] unit N: ...` header — no parsing, no PASS/FAIL.
|
||||
* `-u 0` / `-u 1` for one switch unit, `-i <sec>` for the interval, `-n` for a dry run. `FDR_PORTS` overrides the port list.
|
||||
|
||||
**FDR runs alongside the traffic test in Script A, B and C**
|
||||
* **Script A** wraps its traffic baseline: `fdr start` after `init`, `fdr clear` after `clear`, `fdr rdcnt` after the run, `fdr stop` after the traffic stop. The traffic run is now **40 s instead of 15 s**, so the counters are read after the first 30 s interval has been published — the same rule as `prbsstat Ber`.
|
||||
* **Script B** starts and clears FDR with the traffic setup, before the soak loop — the counters run for the whole soak.
|
||||
* **Script C** reads them (`rdcnt`) before stopping the traffic and stops FDR after it — the closing read of the counters Script B started.
|
||||
|
||||
**Script A turns off the unused lanes before the BER baseline**
|
||||
* `unused_lanes.sh off` — TX squelch on the unused retimer lanes and TSC31 (`cd112-cd115`) disabled on the TH6, on both switch boards.
|
||||
|
||||
## 📦 Downloads
|
||||
|
||||
| File | Contents |
|
||||
|---|---|
|
||||
| `Script_ABC_Blanton_V1.2.6.zip` | The full Tera Term working directory, including `Blanton_Script/` to copy onto the DUT |
|
||||
|
||||
```bash
|
||||
chmod +x ~/Blanton_Script/*.sh
|
||||
grep -rlU $'\r' ~/Blanton_Script # expect no output
|
||||
```
|
||||
|
||||
## ⚠️ Before you run
|
||||
|
||||
* **`chmod +x` after deploying.** `blanton_fdr.sh`, `unused_lanes.sh` and `retimer_lanes.sh` are all called by path; `unused_lanes.sh` also refuses to start if `retimer_lanes.sh` is not executable.
|
||||
* **`blanton_fdr.sh stop` sends `fdrstat STOp` — that keyword is inferred from `prbsstat STOp` and has not been checked on the bench.** `bcmcmd` exits 0 even when the BCM shell rejects a command, so if it is wrong, FDR keeps running and only the log shows it. Check the first run.
|
||||
* **FDR only runs when both switch units are enabled** (`SWB_UNIT0 = SWB_UNIT1 = 1`). The single-unit branches have no FDR, and Script A's single-unit traffic run is still 15 s.
|
||||
* **Nothing turns the unused lanes back on.** Script C has no `unused_lanes.sh on`; run it by hand when the DUT is needed in its normal state. Whether a reboot clears it has not been checked.
|
||||
* **`unused_lanes.sh off` is not gated by `SWB_UNIT0` / `SWB_UNIT1`** — it always acts on both boards.
|
||||
* **`blanton_ber.sh` (Script A / C) still uses `p=3` and `sleep 30`**; see v1.2.5.
|
||||
* **Script 4 has no teardown**: finish it with `blanton_tr518.sh stop` **and** `systemctl stop mlucas-amm`.
|
||||
* **`FAN_SPEED` is 100.**
|
||||
|
||||
## 🔗 Links
|
||||
|
||||
* [ARCHITECTURE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/ARCHITECTURE.md) — test flow, data models, constraints
|
||||
* [CLAUDE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/CLAUDE.md) — commands and the bench gotchas
|
||||
|
||||
**Full changelog:** [V1.2.5...V1.2.6](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/compare/V1.2.5...V1.2.6)
|
||||
@@ -1,7 +1,7 @@
|
||||
; =============================================================================
|
||||
; Script A for Blanton
|
||||
; Version : V1.2.3
|
||||
; Date : 2026-09-23
|
||||
; Version : V1.2.6
|
||||
; Date : 2026-10-21
|
||||
; Author : ETWen
|
||||
; =============================================================================
|
||||
; Version History:
|
||||
@@ -740,6 +740,143 @@
|
||||
; !! without -q the full PM table is printed every round, and
|
||||
; Script 4 loops once a minute - the log grows by one full
|
||||
; table per minute
|
||||
; V1.2.4 2026-10-01 Blanton_Script/tray_id_stress.sh Created v1.0.0 - Tray ID I2C write / read-back stress
|
||||
; Buses 34 / 35 / 38 / 39, device 0x70, register 0x02. Each
|
||||
; bus: write 0xA5, read back, compare; write 0x5A, read back,
|
||||
; compare - the two patterns put every bit in both states
|
||||
; One line per step (PASS / FAIL / ERROR), then a per-bus
|
||||
; Summary table and 'Tray ID stress RESULT: PASS|FAIL'
|
||||
; Exit 0 = all PASS, 1 = any FAIL or I2C error, 2 = usage
|
||||
; -n N repeats the sequence N times; buses / addr / reg /
|
||||
; patterns are editable at the top of the file
|
||||
; The original value is read first and written back at the
|
||||
; end (verified by a read). -R leaves the register at 0x5A
|
||||
; !! FAIL = the read worked but returned the wrong value;
|
||||
; ERROR = i2cset / i2cget itself failed. They are counted
|
||||
; apart because they point at different faults
|
||||
; !! a bus whose original value cannot be read is NOT
|
||||
; restored (there is nothing to restore to) - the line
|
||||
; says so
|
||||
; !! called by path, so it needs the exec bit on the DUT:
|
||||
; chmod +x ~/Blanton_Script/*.sh
|
||||
; ScriptA Add Tray ID stress after show_dmesg (one pass, baseline)
|
||||
; ScriptB Add Tray ID stress to every soak round, before sleep 60
|
||||
; Each round now writes 0xA5 / 0x5A to four Tray ID
|
||||
; registers and restores them - 12 writes per round
|
||||
; 6_Blanton_Script_BER_Cycle.ttl Added - Diag / SONiC BER cycle, a STANDALONE macro (not A/B/C)
|
||||
; Each cycle: PRBS BER on unit 0 in the Diag OS, cold boot
|
||||
; into SONiC, the same PRBS BER again, cold boot back to
|
||||
; Diag; while 1, no end. Boot selection drives the BIOS
|
||||
; Boot Manager ('USB Device' = Diag, 'Hard Drive' = SONiC)
|
||||
; Log: Logs\Blanton_BER_Cycle_<ts>.log, timestamps always on
|
||||
; Report tools (not shipped): tmp/BER_Test_Cycle/
|
||||
; parse_multi.py, gen_multi_html.py, validate_prbsget.py
|
||||
; prbsstat STArt Interval=30, then sleep 40, then Ber
|
||||
; !! the sleep MUST be longer than the Interval. Checked
|
||||
; against the error counts that 'prbs get' reports in the
|
||||
; same cycle: with sleep 10 Diag read ~60x low and SONiC
|
||||
; ~40x low; with sleep 30 (= Interval) Diag was still
|
||||
; ~60x low - its Ber is sent 30.15 s after STArt, just
|
||||
; before the first interval is published. Interval=30 +
|
||||
; sleep 40 matched on both sides over 73 cycles. Every
|
||||
; BER log taken before 2026-09-30 14:13 is low by 40-60x
|
||||
; !! SONiC -> Diag cold boot writes pcimem
|
||||
; /sys/bus/pci/devices/0000:05:00.0/resource0 0x480 with a
|
||||
; hard-coded BDF (the Diag side uses fpga_switch.sh, which
|
||||
; finds the FPGA itself). Check the BDF on every unit
|
||||
; !! the SONiC password is the YourPaSsWoRd placeholder and
|
||||
; the macro does not include config.ttl or secret/
|
||||
; !! prompt_sonic_root is 'root@sonic:~#'. A unit whose
|
||||
; hostname is not 'sonic' (M02 = Margin02) needs the
|
||||
; prompts edited or the macro waits forever
|
||||
; !! fan-speed-control.sh 30 is set on the SONiC side only;
|
||||
; SONiC runs ~11 C hotter than Diag, a variable in any
|
||||
; Diag vs SONiC comparison
|
||||
; !! measures unit 0 only, port 268 not in the list, yet
|
||||
; wait_init still waits for BOTH units (SWB_UNIT0/1 = 1)
|
||||
; V1.2.5 2026-10-21 Blanton_Script/blanton_ber_debug.sh Created v1.0.0 - raw BER run of tools/BER_Test.txt
|
||||
; prbs set p=p31, prbs get x2, prbsstat STArt Interval=30,
|
||||
; sleep 40, Ber, STOp, prbs clear. Every bcmcmd output is
|
||||
; printed as is under a '### [time] unit N: ...' header - no
|
||||
; parsing, no PASS/FAIL, no summary. -u 0 / -u 1, default both
|
||||
; BER_POLY / BER_INTERVAL / BER_WAIT / BER_PORTS overridable
|
||||
; !! the port list is the 200G ports only, no 268 - same as
|
||||
; BER_Test.txt. BER_PORTS="...,268" adds the 100G uplink
|
||||
; !! p=p31 is verified on the bench. blanton_ber.sh (and so
|
||||
; Script A / C) still sets p=3 - the two runs do not measure
|
||||
; the same pattern unless p=3 is PRBS31 as well
|
||||
; !! standalone, no TTL calls it
|
||||
; Blanton_Script/retimer_lanes.sh Created - TX off / on / status for lanes of one Agera3 retimer
|
||||
; retimer_lanes.sh <asic 0|1> <addr> <lane_map> <off|on|status>
|
||||
; Acts on the sys AND the line side. --method squelch (default,
|
||||
; TX squelch, lanes stay powered) or power (TX+RX power-down,
|
||||
; needs an agera3 with the 'power' command - exit 4 if not)
|
||||
; Reads back after the change: PASS / FAIL, exit 3 on mismatch
|
||||
; !! 'off' is REFUSED (exit 2) on a lane with RX PMD lock, i.e.
|
||||
; one that receives a signal. --force overrides
|
||||
; !! runs agera3 through sudo, 30 s timeout per call
|
||||
; Blanton_Script/unused_lanes.sh Created - apply off / on / status to every unused lane
|
||||
; Table at the top: 14 retimer rows (7 fully unused, 7 with
|
||||
; lanes 4,5 unused) and 1 direct-TH6 row (TSC31, cd112-cd115),
|
||||
; the same rows on both switch boards. Retimer rows go through
|
||||
; retimer_lanes.sh, TH6 rows through 'port ... enable=' in
|
||||
; syncdN's bcmcmd. --asic 0|1|all; --th6 also turns off the TH6
|
||||
; ports behind the retimer rows; --only <target> for one row
|
||||
; Ends with ok / refused / failed counts, exit 1 if any failed
|
||||
; !! calls retimer_lanes.sh from its own directory and checks
|
||||
; its exec bit - chmod +x both after deploying
|
||||
; !! bash only (mapfile, [[ =~ ]]), not sh
|
||||
; utils/setup_pmon.ttl Add TH6_SWB0 / TH6_SWB1 power readback after show platform current
|
||||
; Every PMON snapshot (A / B / C / 4 / 5) now has the 19 rails
|
||||
; of each switch board with V x I and TOTAL POWER
|
||||
; !! Script 4 already called both readbacks in its loop right
|
||||
; after setup_pmon - it now reads them TWICE per round
|
||||
; !! every Script B soak round gets longer by both readbacks
|
||||
; ScriptB Add --force to qfx5252-stress-usb
|
||||
; 5_.._Boot_Cycle.ttl Window title shows the cycle count every round
|
||||
; 'Reboot Cycle Test : n' (EN_Cold_Warm_boot = 1) or
|
||||
; 'Power Cycle Test : n' (= 2), set with settitle
|
||||
; Add --force to qfx5252-stress-usb, same as Script B
|
||||
; 5_1_Blanton_Script_Boot_Cycle_Fast.ttl Added - Script 5 without the traffic run, a STANDALONE macro
|
||||
; Identical to 5_.._Boot_Cycle.ttl except that Check Pt8 runs
|
||||
; only 'blanton_traffic_linespeed ps' - no init / clear / show
|
||||
; / start / pause 15 / stop / report. A shorter cycle when the
|
||||
; point is the number of boots
|
||||
; !! a second copy of the same macro: a fix to one has to be
|
||||
; made to the other as well
|
||||
; !! EN_Cold_Warm_boot = 0 (the config.ttl default) hangs it,
|
||||
; same as Script 5
|
||||
; tools/BER_Test.txt p=3 -> p=p31; add a unit 1 block, a both-units block and
|
||||
; port en=0 / en=1 for all cabled ports on each unit
|
||||
; V1.2.6 2026-10-21 Blanton_Script/blanton_fdr.sh Created v1.0.0 - FDR statistics through phydiag fdrstat
|
||||
; start / clear / rdcnt / stop on ports '1-259,270-565':
|
||||
; fdrstat STArt bin_group=both Interval=30 / clear / Counters /
|
||||
; STOp. bcmcmd output printed as is, no parsing or PASS/FAIL
|
||||
; -u 0 / -u 1 (default both), -i <sec> Interval, -n dry run
|
||||
; !! 'stop' sends 'fdrstat STOp', by analogy with prbsstat STOp
|
||||
; - NOT verified on the bench. If the BCM shell rejects it,
|
||||
; FDR keeps running and only the log shows it (bcmcmd exits 0)
|
||||
; !! called by path - chmod +x ~/Blanton_Script/*.sh
|
||||
; ScriptA Turn off unused lanes before the BER baseline
|
||||
; unused_lanes.sh off - both units, TX squelch on the unused
|
||||
; retimer lanes and TSC31 (cd112-cd115) disabled on the TH6
|
||||
; !! nothing turns them back on: no 'unused_lanes.sh on' in
|
||||
; Script C. They stay off until 'unused_lanes.sh on' is run
|
||||
; by hand (whether a reboot clears them is not checked)
|
||||
; !! not gated by SWB_UNIT0 / SWB_UNIT1 - always both units
|
||||
; !! needs the exec bit on unused_lanes.sh AND retimer_lanes.sh
|
||||
; ScriptA FDR around the traffic baseline (SWB_UNIT0 = SWB_UNIT1 = 1 only)
|
||||
; init -> fdr start -> clear -> fdr clear -> ... -> start ->
|
||||
; sleep 40 -> fdr rdcnt -> traffic stop -> fdr stop -> report
|
||||
; Traffic sleep 15 -> 40 so rdcnt reads after the first 30 s
|
||||
; Interval is published (same rule as prbsstat Ber)
|
||||
; !! the single-unit branches have no FDR and still sleep 15
|
||||
; ScriptB fdr start + fdr clear with the traffic setup, before the loop
|
||||
; (SWB_UNIT0 = SWB_UNIT1 = 1 only) - the counters run for the
|
||||
; whole soak
|
||||
; ScriptC fdr rdcnt before traffic stop, fdr stop after it
|
||||
; (SWB_UNIT0 = SWB_UNIT1 = 1 only) - the closing read of the
|
||||
; counters Script B started, bracketing the soak
|
||||
; =============================================================================
|
||||
include "config.ttl"
|
||||
|
||||
@@ -897,6 +1034,10 @@ endif
|
||||
include "utils/setup_pmon.ttl"
|
||||
include "utils/show_dmesg.ttl"
|
||||
|
||||
; ========== Tray ID Stress Test ==========
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/tray_id_stress.sh"
|
||||
|
||||
;include "utils/xxx.ttl"
|
||||
;wait prompt_sonic_root
|
||||
;flushrecv
|
||||
@@ -949,6 +1090,10 @@ sendln "config feature state lldp disabled"
|
||||
wait prompt_sonic_root
|
||||
sendln "config save -y"
|
||||
|
||||
; ========== Turn off unused lanes ==========
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/unused_lanes.sh off"
|
||||
|
||||
; ========== BER ==========
|
||||
; Baseline sweep, taken BEFORE the traffic run - ScriptC takes the closing
|
||||
; one after its traffic report, so the pair brackets the soak.
|
||||
@@ -1005,18 +1150,26 @@ if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed init"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/blanton_fdr.sh start"
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed clear"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/blanton_fdr.sh clear"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 5"
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed show"
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed start"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 15"
|
||||
sendln "sleep 40"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/blanton_fdr.sh rdcnt"
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed stop"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/blanton_fdr.sh stop"
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed report"
|
||||
elseif SWB_UNIT0 = 1 && SWB_UNIT1 = 0 then
|
||||
wait prompt_sonic_root
|
||||
|
||||
@@ -60,7 +60,7 @@ usb_dev = groupmatchstr1
|
||||
|
||||
wait prompt_sonic_root
|
||||
;sprintf2 cmd "bgctl run qfx5252-stress-usb %s 256M --runtime 86400 --passes 1 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log" usb_dev
|
||||
sprintf2 cmd "bgctl run qfx5252-stress-usb %s 256M --runtime %d --passes %d --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log" usb_dev USB_RUNTIME USB_COUNT
|
||||
sprintf2 cmd "bgctl run qfx5252-stress-usb %s 256M --runtime %d --passes %d --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log --force" usb_dev USB_RUNTIME USB_COUNT
|
||||
sendln cmd
|
||||
|
||||
;wait prompt_sonic_root
|
||||
@@ -138,8 +138,12 @@ if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed init"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/blanton_fdr.sh start"
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed clear"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/blanton_fdr.sh clear"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 5"
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed show"
|
||||
@@ -186,6 +190,11 @@ while 1
|
||||
sendln "jobs"
|
||||
wait prompt_sonic_root
|
||||
sendln "systemctl is-active mlucas-amm"
|
||||
|
||||
; ========== Tray ID Stress Test ==========
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/tray_id_stress.sh"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 60"
|
||||
endwhile
|
||||
|
||||
@@ -85,9 +85,13 @@ sendln "show interfaces status Ethernet513,Ethernet514"
|
||||
|
||||
; ========== CHECK Traffic counters ==========
|
||||
if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/blanton_fdr.sh rdcnt"
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed stop"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/blanton_fdr.sh stop"
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed report"
|
||||
elseif SWB_UNIT0 = 1 && SWB_UNIT1 = 0 then
|
||||
wait prompt_sonic_root
|
||||
|
||||
@@ -0,0 +1,412 @@
|
||||
include "config.ttl"
|
||||
|
||||
flushrecv
|
||||
;================================================================
|
||||
; Log File Creation
|
||||
;================================================================
|
||||
gettime str_starttime "%Y%m%d-%H%M%S"
|
||||
getdir mdir
|
||||
|
||||
if EN_log = 1 then
|
||||
if EN_Cold_Warm_boot = 1 then
|
||||
sprintf2 filename '%s\Logs\%s_%s_%s.log' mdir project_name "Reboot_Cycle" str_starttime
|
||||
logopen filename 0 1 1 1
|
||||
elseif EN_Cold_Warm_boot = 2 then
|
||||
sprintf2 filename '%s\Logs\%s_%s_%s.log' mdir project_name "Power_Cycle" str_starttime
|
||||
logopen filename 0 1 1 1
|
||||
else
|
||||
endif
|
||||
endif
|
||||
|
||||
cnt_cycle = 0
|
||||
|
||||
while 1
|
||||
cnt_cycle = cnt_cycle + 1
|
||||
if EN_Cold_Warm_boot = 1 then
|
||||
sprintf2 log_cycle_msg 'Reboot Cycle Test : %d' cnt_cycle
|
||||
settitle log_cycle_msg
|
||||
elseif EN_Cold_Warm_boot = 2 then
|
||||
sprintf2 log_cycle_msg 'Power Cycle Test : %d' cnt_cycle
|
||||
settitle log_cycle_msg
|
||||
else
|
||||
endif
|
||||
; ========== Root Login ==========
|
||||
wait prompt_login
|
||||
sendln "admin"
|
||||
wait "Password:"
|
||||
sendln "YourPaSsWoRd"
|
||||
wait prompt_sonic
|
||||
sendln "sudo -i"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 10"
|
||||
|
||||
if EN_Cold_Warm_boot = 1 then
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strTitle "echo -e '\033[1;32mReboot Cycle : %d \033[0m'" cnt_cycle
|
||||
sendln strTitle
|
||||
elseif EN_Cold_Warm_boot = 2 then
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strTitle "echo -e '\033[1;32mPower Cycle : %d \033[0m'" cnt_cycle
|
||||
sendln strTitle
|
||||
else
|
||||
endif
|
||||
|
||||
; ========== Pre Setting ==========
|
||||
; Make log directory
|
||||
wait prompt_sonic_root
|
||||
sendln "mkdir ./logs"
|
||||
|
||||
; Setting System Time
|
||||
getdate datestr
|
||||
gettime timestr
|
||||
sprintf2 cmd 'sudo date -s "%s %s"' datestr timestr
|
||||
sendln cmd
|
||||
|
||||
; ========== FAN SPEED ==========
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 18-0020 > /sys/bus/i2c/drivers/max31790/unbind"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep .5"
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 18-0020 > /sys/bus/i2c/drivers/max31790/bind"
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 25-0020 > /sys/bus/i2c/drivers/max31790/unbind"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep .5"
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 25-0020 > /sys/bus/i2c/drivers/max31790/bind"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sprintf2 fan_ctrl_cmd 'fan-speed-control.sh %d' FAN_SPEED
|
||||
sendln fan_ctrl_cmd
|
||||
|
||||
wait "Set all configured fan channels to"
|
||||
sendln "y"
|
||||
|
||||
; ========== Wait DUT Init ==========
|
||||
include "utils/wait_init.ttl"
|
||||
|
||||
; ========== DUT Info ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt1 "echo -e '\033[36mCheck Pt1 : DUT Info\033[0m'"
|
||||
sendln strCKPt1
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "show boot"
|
||||
wait prompt_sonic_root
|
||||
sendln "show version"
|
||||
wait prompt_sonic_root
|
||||
sendln "fwutil show status"
|
||||
wait prompt_sonic_root
|
||||
sendln "show system-memory"
|
||||
wait prompt_sonic_root
|
||||
sendln "show service"
|
||||
wait prompt_sonic_root
|
||||
sendln "show platform syseeprom"
|
||||
wait prompt_sonic_root
|
||||
sendln "show platform ssdhealth"
|
||||
wait prompt_sonic_root
|
||||
sendln "qfx5252-tpm-version"
|
||||
wait prompt_sonic_root
|
||||
sendln "/usr/sbin/nvme smart-log -H /dev/nvme0"
|
||||
wait prompt_sonic_root
|
||||
sendln "/usr/sbin/smartctl -x /dev/nvme0"
|
||||
|
||||
; ========== BMC version ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt2 "echo -e '\033[36mCheck Pt2 : BMC Info\033[0m'"
|
||||
sendln strCKPt2
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "bmc-first-enroll"
|
||||
wait prompt_sonic_root
|
||||
sendln "bmc-manager version"
|
||||
wait prompt_sonic_root
|
||||
sendln "bmc-manager status"
|
||||
|
||||
; ========== Load Shell Script ==========
|
||||
wait prompt_sonic_root
|
||||
sendln "source ~/Blanton_Script/blanton_fpga_pcimem.sh"
|
||||
wait prompt_sonic_root
|
||||
sendln "source ~/Blanton_Script/blanton_cb_i2c.sh"
|
||||
wait prompt_sonic_root
|
||||
sendln "source ~/Blanton_Script/blanton_icb_vi2c.sh"
|
||||
wait prompt_sonic_root
|
||||
sendln "source ~/Blanton_Script/blanton_pwr_data.sh"
|
||||
wait prompt_sonic_root
|
||||
sendln "source ~/Blanton_Script/blanton_traffic_linespeed.sh"
|
||||
wait prompt_sonic_root
|
||||
sendln "source ~/Blanton_Script/LTC2980_Margin_Script/margin.sh"
|
||||
|
||||
; ========== CLEAR PCIE Error ==========
|
||||
include "utils/show_pcie_error_reg_TH6_SWB0.ttl"
|
||||
include "utils/show_pcie_error_reg_TH6_SWB1.ttl"
|
||||
include "utils/show_pcie_error_reg_FPGA.ttl"
|
||||
include "utils/show_pcie_error_reg_BMC.ttl"
|
||||
include "utils/show_pcie_error_reg_DDR.ttl"
|
||||
include "utils/show_pcie_error_reg_I210.ttl"
|
||||
include "utils/show_pcie_error_reg_SSD.ttl"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "/usr/sbin/ras-mc-ctl --summary"
|
||||
|
||||
; ========== Check PCIE tree + PCIE link status + GET PCIE bandwidth Test ==========
|
||||
include "utils/pcie_bus.ttl"
|
||||
|
||||
; ========== TAKE DATA ==========
|
||||
include "utils/setup_pmon.ttl"
|
||||
include "utils/show_dmesg.ttl"
|
||||
|
||||
; ========== 10G/1G MGMT Ping Test ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt3 "echo -e '\033[36mCheck Pt3 : Mgmt Ping Test\033[0m'"
|
||||
sendln strCKPt3
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/mgmt_ping_monitor.sh start"
|
||||
wait prompt_sonic_root
|
||||
pause 30
|
||||
sendln "~/Blanton_Script/mgmt_ping_monitor.sh stop"
|
||||
wait prompt_sonic_root
|
||||
sendln "cat ~/Blanton_Script/log/mgmt_ping.log"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/mgmt_ping_monitor.sh clear"
|
||||
|
||||
; ========== NFC Test ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt4 "echo -e '\033[36mCheck Pt4 : NFC Test\033[0m'"
|
||||
sendln strCKPt4
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/nfc_polling.sh start"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/nfc_polling.sh status"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 20"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/nfc_polling.sh stop"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/nfc_polling.sh report"
|
||||
|
||||
; ========== SSD read/write ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt5 "echo -e '\033[36mCheck Pt5 : SSD Test\033[0m'"
|
||||
sendln strCKPt5
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "rm -rf /host/hw-eval/jobs/qfx5252-stress-ssd.log"
|
||||
wait prompt_sonic_root
|
||||
sendln "qfx5252-stress-ssd 1G --runtime 30 --passes 2 --write --force --log /host/hw-eval/jobs/qfx5252-stress-ssd.log"
|
||||
wait prompt_sonic_root
|
||||
sendln "cat /host/hw-eval/jobs/qfx5252-stress-ssd.log"
|
||||
|
||||
; ========== USB read/write ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt6 "echo -e '\033[36mCheck Pt6 : USB Test\033[0m'"
|
||||
sendln strCKPt6
|
||||
|
||||
; ---- Get USB partition node -> usb_dev ----
|
||||
usb_dev = ''
|
||||
wait prompt_sonic_root
|
||||
sendln 'D=$(bash ~/Blanton_Script/usb_target.sh -o dev 2>/dev/null); echo "<<D""EV=${D:-NONE}>>"'
|
||||
waitregex '<<DEV=([^>]*)>>'
|
||||
usb_dev = groupmatchstr1
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "rm -rf /host/hw-eval/jobs/qfx5252-stress-usb.log"
|
||||
wait prompt_sonic_root
|
||||
sprintf2 cmd "qfx5252-stress-usb %s 256M --runtime 30 --passes 2 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log --force" usb_dev
|
||||
sendln cmd
|
||||
wait prompt_sonic_root
|
||||
sendln "cat /host/hw-eval/jobs/qfx5252-stress-usb.log"
|
||||
|
||||
; ========== BMC USB Test ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt7 "echo -e '\033[36mCheck Pt7 : BMC USB Test\033[0m'"
|
||||
sendln strCKPt7
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln 'echo "NCMIF=$(ls -d /sys/bus/usb/drivers/cdc_ncm/*/net/* 2>/dev/null | head -n 1 | xargs -r basename)"'
|
||||
; timeout is GLOBAL and sticky: left at 15, every 'wait' below gives up after
|
||||
; 15 s instead of blocking, the macro runs ahead of the DUT and the whole
|
||||
; cycle desynchronises. Restore it BEFORE the branch so both paths are
|
||||
; covered - the ping block below waits on 'sleep 10', which is already two
|
||||
; thirds of the 15 s cap on a loaded DUT.
|
||||
timeout = 15
|
||||
waitregex 'NCMIF=[A-Za-z0-9_-]+'
|
||||
ncm_found = result ; hold it: 'result' is reused below
|
||||
timeout = 0 ; restore, both paths
|
||||
if ncm_found = 0 then
|
||||
messagebox 'cdc_ncm interface not found. Ping test skipped.' 'ERROR'
|
||||
goto skip_ping
|
||||
endif
|
||||
strlen matchstr
|
||||
cut_len = result - 6 ; 'NCMIF=' = 6 chars
|
||||
strcopy matchstr 7 cut_len ncm_if ; -> ncm_if = "eth2" / "eth3"
|
||||
|
||||
sprintf2 cmd 'ip -br link show %s' ncm_if
|
||||
wait prompt_sonic_root
|
||||
sendln cmd
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln 'systemctl stop qfx5252-bmc-usb-net-test.service 2>/dev/null || true'
|
||||
wait prompt_sonic_root
|
||||
sendln 'systemctl reset-failed qfx5252-bmc-usb-net-test.service 2>/dev/null || true'
|
||||
sprintf2 cmd 'systemd-run --unit=qfx5252-bmc-usb-net-test --property=Type=exec /usr/bin/ping -I %s -i 1 -W 2 -w 14400 192.168.200.200' ncm_if
|
||||
wait prompt_sonic_root
|
||||
sendln cmd
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 10"
|
||||
wait prompt_sonic_root
|
||||
sendln "systemctl stop qfx5252-bmc-usb-net-test.service"
|
||||
wait prompt_sonic_root
|
||||
sendln "journalctl -u qfx5252-bmc-usb-net-test.service --no-pager"
|
||||
|
||||
:skip_ping
|
||||
timeout = 0 ; backstop, same as Script B
|
||||
|
||||
; ========== 100G Port Setting ==========
|
||||
wait prompt_sonic_root
|
||||
sendln "sudo sfputil lpmode off Ethernet513"
|
||||
wait prompt_sonic_root
|
||||
sendln "sudo sfputil lpmode off Ethernet514"
|
||||
wait prompt_sonic_root
|
||||
sendln "config interface -n asic0 startup Ethernet513"
|
||||
wait prompt_sonic_root
|
||||
sendln "config interface -n asic1 startup Ethernet514"
|
||||
wait prompt_sonic_root
|
||||
sendln "config save -y"
|
||||
|
||||
; ========== First Traffic Test ==========
|
||||
; Silent MAC
|
||||
wait prompt_sonic_root
|
||||
sendln "config feature state lldp disabled"
|
||||
wait prompt_sonic_root
|
||||
sendln "config save -y"
|
||||
|
||||
; ========== 100G Port Status ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt8 "echo -e '\033[36mCheck Pt8 : Port Status and 15sec Traffic \033[0m'"
|
||||
sendln strCKPt8
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "show interfaces status Ethernet513,Ethernet514"
|
||||
|
||||
; ========== Traffic Test ==========
|
||||
if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed ps"
|
||||
elseif SWB_UNIT0 = 1 && SWB_UNIT1 = 0 then
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed ps -u 0"
|
||||
elseif SWB_UNIT0 = 0 && SWB_UNIT1 = 1 then
|
||||
wait prompt_sonic_root
|
||||
sendln "blanton_traffic_linespeed ps -u 1"
|
||||
else
|
||||
|
||||
endif
|
||||
|
||||
; ========== BER ==========
|
||||
; PRBS takes the SerDes out of normal operation, so this runs AFTER the
|
||||
; traffic report. sleep 30 matches blanton_ber.sh BER_INTERVAL - reporting
|
||||
; earlier reads an interval that has not finished accumulating.
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt8 "echo -e '\033[36mCheck Pt9 : BER Test \033[0m'"
|
||||
sendln strCKPt8
|
||||
|
||||
if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh init"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh start"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 30"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh report"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh stop"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh clear"
|
||||
elseif SWB_UNIT0 = 1 && SWB_UNIT1 = 0 then
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh init -u 0"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh start -u 0"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 30"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh report -u 0"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh stop -u 0"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh clear -u 0"
|
||||
elseif SWB_UNIT0 = 0 && SWB_UNIT1 = 1 then
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh init -u 1"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh start -u 1"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 30"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh report -u 1"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh stop -u 1"
|
||||
wait prompt_sonic_root
|
||||
sendln "./Blanton_Script/blanton_ber.sh clear -u 1"
|
||||
else
|
||||
|
||||
endif
|
||||
|
||||
; ========== NVME Err Info ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt9 "echo -e '\033[36mCheck Pt10 : NVME Err Info \033[0m'"
|
||||
sendln strCKPt9
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "/usr/sbin/nvme smart-log -H /dev/nvme0"
|
||||
wait prompt_sonic_root
|
||||
sendln "/usr/sbin/smartctl -x /dev/nvme0"
|
||||
|
||||
; ========== TAKE DATA ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt10 "echo -e '\033[36mCheck Pt11 : Platform Data \033[0m'"
|
||||
sendln strCKPt10
|
||||
include "utils/setup_pmon.ttl"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt12 "echo -e '\033[36mCheck Pt12 : Dmesg_i2c \033[0m'"
|
||||
sendln strCKPt12
|
||||
include "utils/show_dmesg.ttl"
|
||||
|
||||
; ========== Check PCIE error counters ==========
|
||||
wait prompt_sonic_root
|
||||
sprintf2 strCKPt13 "echo -e '\033[36mCheck Pt13 : PCIE Error Counters \033[0m'"
|
||||
sendln strCKPt13
|
||||
include "utils/show_pcie_error_reg_TH6_SWB0.ttl"
|
||||
include "utils/show_pcie_error_reg_TH6_SWB1.ttl"
|
||||
include "utils/show_pcie_error_reg_FPGA.ttl"
|
||||
include "utils/show_pcie_error_reg_BMC.ttl"
|
||||
include "utils/show_pcie_error_reg_DDR.ttl"
|
||||
include "utils/show_pcie_error_reg_I210.ttl"
|
||||
include "utils/show_pcie_error_reg_SSD.ttl"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "/usr/sbin/ras-mc-ctl --summary"
|
||||
|
||||
; ========== Show Power on uptime ==========
|
||||
wait prompt_sonic_root
|
||||
sendln "show uptime"
|
||||
|
||||
; ========== Show Power on uptime ==========
|
||||
if EN_Cold_Warm_boot = 1 then
|
||||
wait prompt_sonic_root
|
||||
sendln "reboot"
|
||||
elseif EN_Cold_Warm_boot = 2 then
|
||||
wait prompt_sonic_root
|
||||
sendln "pcimem /sys/bus/pci/devices/0000:05:00.0/resource0 0x480 w 0xD0000"
|
||||
else
|
||||
endif
|
||||
|
||||
|
||||
wait "Booting in blind mode"
|
||||
endwhile
|
||||
@@ -22,6 +22,14 @@ cnt_cycle = 0
|
||||
|
||||
while 1
|
||||
cnt_cycle = cnt_cycle + 1
|
||||
if EN_Cold_Warm_boot = 1 then
|
||||
sprintf2 log_cycle_msg 'Reboot Cycle Test : %d' cnt_cycle
|
||||
settitle log_cycle_msg
|
||||
elseif EN_Cold_Warm_boot = 2 then
|
||||
sprintf2 log_cycle_msg 'Power Cycle Test : %d' cnt_cycle
|
||||
settitle log_cycle_msg
|
||||
else
|
||||
endif
|
||||
; ========== Root Login ==========
|
||||
wait prompt_login
|
||||
sendln "admin"
|
||||
@@ -207,7 +215,7 @@ while 1
|
||||
wait prompt_sonic_root
|
||||
sendln "rm -rf /host/hw-eval/jobs/qfx5252-stress-usb.log"
|
||||
wait prompt_sonic_root
|
||||
sprintf2 cmd "qfx5252-stress-usb %s 256M --runtime 30 --passes 2 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log" usb_dev
|
||||
sprintf2 cmd "qfx5252-stress-usb %s 256M --runtime 30 --passes 2 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log --force" usb_dev
|
||||
sendln cmd
|
||||
wait prompt_sonic_root
|
||||
sendln "cat /host/hw-eval/jobs/qfx5252-stress-usb.log"
|
||||
|
||||
@@ -0,0 +1,315 @@
|
||||
;================================================================
|
||||
; Prompt Definitions
|
||||
;================================================================
|
||||
prompt_login = "sonic login:"
|
||||
prompt_sonic = "admin@sonic:~$"
|
||||
prompt_sonic_root = "root@sonic:~#"
|
||||
prompt_diag = "root@(none):~#"
|
||||
|
||||
; ============================================================
|
||||
; [1] Config
|
||||
; ============================================================
|
||||
SWB_UNIT0 = 1 ; 1 = this DUT has switch unit 0, wait for it ; 0 = skip
|
||||
SWB_UNIT1 = 1 ; 1 = this DUT has switch unit 1, wait for it ; 0 = skip
|
||||
|
||||
bb_post_hotkey = 'Post Code>>:0226' ; 看到此 POST code 後開始送 ESC
|
||||
bb_esc_ack = 'Esc is pressed' ; BIOS 收到 ESC 的回應訊息
|
||||
bb_fp_continue = 'continue to booting' ; Front Page：Continue 反白時的說明欄（同一 row 內的字串）
|
||||
bb_fp_bootmgr = 'you to the Boot Manager' ; Front Page：Boot Manager 反白時的說明欄
|
||||
bb_bm_header = 'EFI Boot Devices' ; Boot Manager 清單標題
|
||||
bb_bm_footer = 'ESC to exit' ; Boot Manager 頁面最後一段文字（畫完判定）
|
||||
|
||||
bb_key_esc = #27
|
||||
bb_key_down = #27'[B'
|
||||
bb_key_enter = #13
|
||||
|
||||
;diag_tok = 'KINGSHARKS' ; EFI USB Device (KINGSHARKS-ANTU04)
|
||||
;sonic_tok = 'J983670007' ; EFI Hard Drive (J983670007-TS2TMTE712P-VS2)
|
||||
diag_tok = 'USB Device' ; EFI USB Device (KINGSHARKS-ANTU04)
|
||||
sonic_tok = 'Hard Drive' ; EFI Hard Drive (J983670007-TS2TMTE712P-VS2)
|
||||
|
||||
|
||||
diag_sig = 'ast1813b_diag' ; EFI Shell 執行 startup.nsh 載入的 diag kernel
|
||||
sonic_sig = 'SONiC-OS' ; SONiC GRUB entry 名稱（請依實際 GRUB 畫面確認）
|
||||
|
||||
gettime str_starttime "%Y%m%d-%H%M%S"
|
||||
getdir mdir
|
||||
sprintf2 filename '%s\Logs\%s_%s_%s.log' mdir "Blanton" "BER_Cycle" str_starttime
|
||||
; logopen <file> <binary> <append> <PlainText> <timestamp>
|
||||
; binary=0 text mode, so PlainText / timestamp are honoured
|
||||
; append=1 keep earlier cycles, do not overwrite
|
||||
; PlainText=1 strip the ANSI colour codes SONiC emits
|
||||
logopen filename 0 1 1 1
|
||||
|
||||
test_cycle = 0
|
||||
|
||||
while 1
|
||||
test_cycle = test_cycle + 1
|
||||
flushrecv
|
||||
logwrite ''#13#10
|
||||
sprintf2 log_cycle_msg 'BER Diag/SONiC Cycle Test : %d'#13#10 test_cycle
|
||||
logwrite '#####################################'#13#10
|
||||
logwrite log_cycle_msg
|
||||
logwrite '#####################################'#13#10
|
||||
settitle log_cycle_msg
|
||||
; ============================================================
|
||||
; [2] Call : Script where switching is needed
|
||||
; ============================================================
|
||||
; ====== Diag Test ======
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=3"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STArt Interval=30"'
|
||||
wait prompt_diag
|
||||
sendln "sleep 40"
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat Ber"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STOp"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs clear"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:dsh -c "phydiag 256-259 dsc"'
|
||||
wait prompt_diag
|
||||
sendln 'swutil 0:show temp'
|
||||
wait prompt_diag
|
||||
sendln "swutil *:extphy core_diag all"
|
||||
wait prompt_diag
|
||||
|
||||
; ---- Diag -> SONiC ----
|
||||
sendln 'fpga_switch.sh cb 0 0x480 0xD0000'
|
||||
bb_target_tok = sonic_tok
|
||||
bb_sig_target = sonic_sig
|
||||
bb_sig_other = diag_sig
|
||||
call bb_boot_to
|
||||
if bb_ok = 0 then
|
||||
sprintf2 bb_msg 'Boot to SONiC failed: %s' bb_err
|
||||
messagebox bb_msg 'bios_boot'
|
||||
end
|
||||
endif
|
||||
|
||||
; ========== SONiC Test ==========
|
||||
wait prompt_login
|
||||
sendln "admin"
|
||||
wait "Password:"
|
||||
sendln "YourPaSsWoRd"
|
||||
wait prompt_sonic
|
||||
sendln "sudo -i"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 10"
|
||||
|
||||
; ========== FAN SPEED ==========
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 18-0020 > /sys/bus/i2c/drivers/max31790/unbind"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep .5"
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 18-0020 > /sys/bus/i2c/drivers/max31790/bind"
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 25-0020 > /sys/bus/i2c/drivers/max31790/unbind"
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep .5"
|
||||
wait prompt_sonic_root
|
||||
sendln "echo 25-0020 > /sys/bus/i2c/drivers/max31790/bind"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sprintf2 fan_ctrl_cmd 'fan-speed-control.sh %d' 30
|
||||
sendln fan_ctrl_cmd
|
||||
|
||||
wait "Set all configured fan channels to"
|
||||
sendln "y"
|
||||
|
||||
; ========== Wait DUT Init ==========
|
||||
include "utils/wait_init.ttl"
|
||||
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=3' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STArt Interval=30' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln "sleep 40"
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat Ber' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STOp' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c " dsh -c ' 39 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs clear' 39 ' "'
|
||||
wait prompt_sonic_root
|
||||
sendln 'bcmcmd -n 0 -c "dsh -c ' 39 'phydiag 256-259 dsc' 39 '"'
|
||||
wait prompt_sonic_root
|
||||
sendln 'show plat temperature'
|
||||
|
||||
; ---- SONiC -> Diag ----
|
||||
wait prompt_sonic_root
|
||||
sendln 'pcimem /sys/bus/pci/devices/0000:05:00.0/resource0 0x480 w 0xD0000'
|
||||
bb_target_tok = diag_tok
|
||||
bb_sig_target = diag_sig
|
||||
bb_sig_other = sonic_sig
|
||||
call bb_boot_to
|
||||
if bb_ok = 0 then
|
||||
sprintf2 bb_msg 'Boot to Diag failed: %s' bb_err
|
||||
messagebox bb_msg 'bios_boot'
|
||||
end
|
||||
endif
|
||||
endwhile
|
||||
|
||||
logclose
|
||||
end
|
||||
|
||||
; ============================================================
|
||||
; [3] Subroutine
|
||||
; ============================================================
|
||||
:bb_boot_to
|
||||
bb_saved_to = timeout
|
||||
call bb_run
|
||||
timeout = bb_saved_to
|
||||
mtimeout = 0
|
||||
return
|
||||
|
||||
:bb_run
|
||||
bb_ok = 0
|
||||
bb_err = ''
|
||||
call bb_enter_bios
|
||||
if bb_ok = 0 return
|
||||
call bb_goto_bootmgr
|
||||
if bb_ok = 0 return
|
||||
call bb_find_idx
|
||||
if bb_ok = 0 return
|
||||
call bb_select
|
||||
call bb_verify
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; 等 POST 0226，之後連送 ESC 直到 BIOS 回應 'Esc is pressed'
|
||||
; ------------------------------------------------------------
|
||||
:bb_enter_bios
|
||||
bb_ok = 0
|
||||
flushrecv ; 清掉 reboot 前的舊資料，避免誤比對
|
||||
timeout = 300
|
||||
mtimeout = 0
|
||||
wait bb_post_hotkey
|
||||
if result = 0 then
|
||||
bb_err = 'timeout waiting POST code 0226'
|
||||
return
|
||||
endif
|
||||
|
||||
timeout = 0
|
||||
mtimeout = 300
|
||||
for bb_i 1 200 ; 300 ms x 200 = 最多約 60 秒
|
||||
send bb_key_esc
|
||||
wait bb_esc_ack
|
||||
if result > 0 then
|
||||
bb_ok = 1
|
||||
break ; 收到 ack 立即停送，避免多餘 ESC 把 Front Page 退掉
|
||||
endif
|
||||
next
|
||||
mtimeout = 0
|
||||
if bb_ok = 0 bb_err = 'no ESC ack from BIOS'
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; Front Page：預設反白在 Continue，按一次 Down 到 Boot Manager
|
||||
; 以右側說明欄文字確認反白位置，再按 Enter
|
||||
; ------------------------------------------------------------
|
||||
:bb_goto_bootmgr
|
||||
bb_ok = 0
|
||||
timeout = 30
|
||||
wait bb_fp_continue
|
||||
if result = 0 then
|
||||
bb_err = 'Front Page not shown'
|
||||
return
|
||||
endif
|
||||
|
||||
mpause 500
|
||||
send bb_key_down
|
||||
timeout = 5
|
||||
wait bb_fp_bootmgr
|
||||
if result = 0 then
|
||||
bb_err = 'cannot highlight Boot Manager'
|
||||
return
|
||||
endif
|
||||
|
||||
mpause 300
|
||||
send bb_key_enter
|
||||
timeout = 15
|
||||
wait bb_bm_header
|
||||
if result = 0 then
|
||||
bb_err = 'Boot Manager page not shown'
|
||||
return
|
||||
endif
|
||||
bb_ok = 1
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; 解析 Boot Manager 清單，計算目標 entry 的 index（0-based）
|
||||
; 每個 entry 以 'EFI '（含 UEFI）或 'SVOS' 開頭計數，命中目標字串即停止
|
||||
; ------------------------------------------------------------
|
||||
:bb_find_idx
|
||||
bb_ok = 0
|
||||
bb_idx = -1
|
||||
bb_cnt = 0
|
||||
timeout = 0
|
||||
mtimeout = 3000
|
||||
for bb_i 1 20
|
||||
wait 'EFI ' 'SVOS' bb_target_tok
|
||||
if result = 0 break ; 清單畫完仍未命中
|
||||
if result = 3 then
|
||||
bb_idx = bb_cnt - 1 ; 目標字串前的 'EFI ' 屬於目標 entry 本身
|
||||
break
|
||||
endif
|
||||
bb_cnt = bb_cnt + 1
|
||||
next
|
||||
mtimeout = 0
|
||||
|
||||
if bb_idx < 0 then
|
||||
bb_err = 'target entry not found in Boot Manager'
|
||||
return
|
||||
endif
|
||||
|
||||
timeout = 5
|
||||
wait bb_bm_footer ; 等整頁畫完才開始按鍵
|
||||
bb_ok = 1
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; 預設反白在第一個 entry，往下移 bb_idx 格後按 Enter
|
||||
; ------------------------------------------------------------
|
||||
:bb_select
|
||||
mpause 300
|
||||
if bb_idx > 0 then ; TTL 的 for 1 0 會倒數執行，必須先擋掉
|
||||
for bb_i 1 bb_idx
|
||||
send bb_key_down
|
||||
timeout = 3
|
||||
wait bb_bm_footer ; BIOS 每按一次會整頁重畫，畫完再按下一次
|
||||
mpause 200
|
||||
next
|
||||
endif
|
||||
send bb_key_enter
|
||||
; 之後不可再送任何按鍵：Diag 走 EFI Shell，
|
||||
; 任何按鍵都會被當成「跳過 / 中斷 startup.nsh」
|
||||
return
|
||||
|
||||
; ------------------------------------------------------------
|
||||
; 同時等目標與另一個 image 的特徵字串
|
||||
; ------------------------------------------------------------
|
||||
:bb_verify
|
||||
bb_ok = 0
|
||||
timeout = 300
|
||||
wait bb_sig_target bb_sig_other
|
||||
if result = 1 then
|
||||
bb_ok = 1
|
||||
elseif result = 2 then
|
||||
bb_err = 'booted into wrong image'
|
||||
else
|
||||
bb_err = 'timeout waiting boot signature'
|
||||
endif
|
||||
return
|
||||
@@ -0,0 +1,100 @@
|
||||
#!/usr/bin/env bash
|
||||
# =============================================================================
|
||||
# blanton_ber_debug.sh -- SerDes BER, raw run of tools/BER_Test.txt
|
||||
# =============================================================================
|
||||
# Version History:
|
||||
# V1.0.0 2026-10-07 First version. Runs the hand-pasted BER flow end to end
|
||||
# (prbs set p=p31 / prbs get x2 / STArt / sleep 40 / Ber /
|
||||
# STOp / clear) and prints every bcmcmd output as is --
|
||||
# no parsing, no PASS/FAIL, no summary. blanton_ber.sh is
|
||||
# the judged version; this one is for looking at the raw
|
||||
# output on the bench.
|
||||
#
|
||||
# Order of operations (per step, unit 0 first, then unit 1):
|
||||
# phydiag <ports> prbs set p=p31
|
||||
# phydiag <ports> prbs get twice: the 1st clears the sticky
|
||||
# phydiag <ports> prbs get "unlocked since last call", the 2nd
|
||||
# is the current lock state
|
||||
# phydiag <ports> prbsstat STArt Interval=30
|
||||
# sleep 40 MUST be > Interval, or Ber is read
|
||||
# before the first interval settles
|
||||
# phydiag <ports> prbsstat Ber
|
||||
# phydiag <ports> prbsstat STOp
|
||||
# phydiag <ports> prbs clear releases the lanes back to normal
|
||||
#
|
||||
# ⚠️ Links show DOWN while PRBS runs -- that is expected.
|
||||
# ⚠️ Do not run together with blanton_ber.sh / blanton_traffic_linespeed.sh /
|
||||
# blanton_tr518.sh -- they all take over the same ports.
|
||||
#
|
||||
# Usage:
|
||||
# ./blanton_ber_debug.sh # unit 0 and 1
|
||||
# ./blanton_ber_debug.sh -u 0 # unit 0 only
|
||||
# ./blanton_ber_debug.sh -u 1 # unit 1 only
|
||||
#
|
||||
# Env overrides:
|
||||
# BCMCMD_CMD=bcmcmd BER_POLY=p=p31 BER_INTERVAL=30 BER_WAIT=40
|
||||
# BER_PORTS="1-24,..." (default: the 200G ports, no 268 -- same as
|
||||
# tools/BER_Test.txt; add ",268" for the 100G uplink)
|
||||
# =============================================================================
|
||||
|
||||
BCMCMD_CMD="${BCMCMD_CMD:-bcmcmd}"
|
||||
BER_UNITS="0 1"
|
||||
BER_PORTS="${BER_PORTS:-1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565}"
|
||||
BER_POLY="${BER_POLY:-p=p31}"
|
||||
BER_INTERVAL="${BER_INTERVAL:-30}"
|
||||
BER_WAIT="${BER_WAIT:-40}"
|
||||
|
||||
usage() {
|
||||
sed -n '/^# Usage:/,/^# =====/p' "$0" | sed '$d; s/^# \{0,1\}//'
|
||||
}
|
||||
|
||||
while [ $# -gt 0 ]; do
|
||||
case "$1" in
|
||||
-u|--unit)
|
||||
case "$2" in
|
||||
0|1) BER_UNITS="$2" ;;
|
||||
*) echo "[ERR ] invalid unit '$2' (use 0 or 1)" >&2; exit 2 ;;
|
||||
esac
|
||||
shift 2 ;;
|
||||
-h|--help) usage; exit 0 ;;
|
||||
*) echo "[ERR ] unknown option '$1'" >&2; usage >&2; exit 2 ;;
|
||||
esac
|
||||
done
|
||||
|
||||
# bcmcmd reads stdin -- keep it on /dev/null (see blanton_traffic_linespeed.sh V0.3.1)
|
||||
_bcm() {
|
||||
local unit="$1"; shift
|
||||
local cmd="dsh -c 'phydiag ${BER_PORTS} $*'"
|
||||
echo
|
||||
echo "### [$(date '+%F %T')] unit $unit: phydiag <ports> $*"
|
||||
"$BCMCMD_CMD" -n "$unit" -c " ${cmd} " </dev/null 2>&1
|
||||
}
|
||||
|
||||
for u in $BER_UNITS; do
|
||||
_bcm "$u" "prbs set ${BER_POLY}"
|
||||
_bcm "$u" "prbs get"
|
||||
_bcm "$u" "prbs get"
|
||||
done
|
||||
|
||||
for u in $BER_UNITS; do
|
||||
_bcm "$u" "prbsstat STArt Interval=${BER_INTERVAL}"
|
||||
done
|
||||
|
||||
echo
|
||||
echo "### [$(date '+%F %T')] sleep ${BER_WAIT}"
|
||||
sleep "$BER_WAIT"
|
||||
|
||||
for u in $BER_UNITS; do
|
||||
_bcm "$u" "prbsstat Ber"
|
||||
done
|
||||
|
||||
for u in $BER_UNITS; do
|
||||
_bcm "$u" "prbsstat STOp"
|
||||
done
|
||||
|
||||
for u in $BER_UNITS; do
|
||||
_bcm "$u" "prbs clear"
|
||||
done
|
||||
|
||||
echo
|
||||
echo "### [$(date '+%F %T')] BER_DEBUG_DONE units: $BER_UNITS"
|
||||
@@ -0,0 +1,98 @@
|
||||
#!/usr/bin/env bash
|
||||
# =============================================================================
|
||||
# blanton_fdr.sh -- SerDes FDR statistics (phydiag fdrstat), raw output
|
||||
# =============================================================================
|
||||
# Version History:
|
||||
# V1.0.0 2026-10-21 First version. start / clear / rdcnt / stop over
|
||||
# 'phydiag <ports> fdrstat ...' through bcmcmd, the same
|
||||
# way blanton_ber_debug.sh drives prbsstat. Every bcmcmd
|
||||
# output is printed as is -- no parsing, no PASS/FAIL.
|
||||
#
|
||||
# Sub-commands (each one runs on unit 0, then unit 1):
|
||||
# start phydiag '<ports>' fdrstat STArt bin_group=both Interval=30
|
||||
# clear phydiag '<ports>' fdrstat clear
|
||||
# rdcnt phydiag '<ports>' fdrstat Counters
|
||||
# stop phydiag '<ports>' fdrstat STOp
|
||||
#
|
||||
# ⚠️ 'stop' sends 'fdrstat STOp', by analogy with 'prbsstat STOp'. It has
|
||||
# not been checked on the bench -- if the BCM shell rejects it, look at
|
||||
# 'phydiag help' (or 'fdrstat' with no argument) for the right keyword.
|
||||
# ⚠️ bcmcmd exits 0 even when the BCM shell refuses a command, so this
|
||||
# script cannot tell success from failure. Read the output.
|
||||
#
|
||||
# Usage:
|
||||
# ./blanton_fdr.sh <start|clear|rdcnt|stop> [-u 0|1] [-i <sec>] [-n]
|
||||
# -u 0 | -u 1 one switch unit only (default: both, 0 then 1)
|
||||
# -i <sec> start: fdrstat Interval (default 30)
|
||||
# -n dry run: print the bcmcmd lines, do not run them
|
||||
#
|
||||
# Env overrides:
|
||||
# BCMCMD_CMD=bcmcmd FDR_PORTS=1-259,270-565 FDR_INTERVAL=30
|
||||
# FDR_BIN_GROUP=both
|
||||
# =============================================================================
|
||||
|
||||
BCMCMD_CMD="${BCMCMD_CMD:-bcmcmd}"
|
||||
FDR_UNITS="0 1"
|
||||
FDR_PORTS="${FDR_PORTS:-1-259,270-565}"
|
||||
FDR_INTERVAL="${FDR_INTERVAL:-30}"
|
||||
FDR_BIN_GROUP="${FDR_BIN_GROUP:-both}"
|
||||
FDR_DRY_RUN=0
|
||||
|
||||
usage() {
|
||||
sed -n '/^# Usage:/,/^# =====/p' "$0" | sed '$d; s/^# \{0,1\}//'
|
||||
}
|
||||
|
||||
[ $# -ge 1 ] || { usage >&2; exit 2; }
|
||||
ACT=$1; shift
|
||||
case "$ACT" in
|
||||
start|clear|rdcnt|stop) ;;
|
||||
-h|--help|help) usage; exit 0 ;;
|
||||
*) echo "[ERR ] unknown sub-command '$ACT'" >&2; usage >&2; exit 2 ;;
|
||||
esac
|
||||
|
||||
while [ $# -gt 0 ]; do
|
||||
case "$1" in
|
||||
-u|--unit)
|
||||
case "$2" in
|
||||
0|1) FDR_UNITS="$2" ;;
|
||||
*) echo "[ERR ] invalid unit '$2' (use 0 or 1)" >&2; exit 2 ;;
|
||||
esac
|
||||
shift 2 ;;
|
||||
-i|--interval)
|
||||
case "$2" in
|
||||
''|*[!0-9]*) echo "[ERR ] invalid interval '$2'" >&2; exit 2 ;;
|
||||
*) FDR_INTERVAL="$2" ;;
|
||||
esac
|
||||
shift 2 ;;
|
||||
-n|--dry-run) FDR_DRY_RUN=1; shift ;;
|
||||
-h|--help) usage; exit 0 ;;
|
||||
*) echo "[ERR ] unknown option '$1'" >&2; usage >&2; exit 2 ;;
|
||||
esac
|
||||
done
|
||||
|
||||
# bcmcmd reads stdin -- keep it on /dev/null (see blanton_traffic_linespeed.sh V0.3.1)
|
||||
_bcm() {
|
||||
local unit="$1"; shift
|
||||
local cmd="dsh -c \"phydiag '${FDR_PORTS}' fdrstat $*\""
|
||||
echo
|
||||
echo "### [$(date '+%F %T')] unit $unit: phydiag '${FDR_PORTS}' fdrstat $*"
|
||||
if [ "$FDR_DRY_RUN" = "1" ]; then
|
||||
echo "[DRY ] $BCMCMD_CMD -n $unit -c ' ${cmd} '"
|
||||
return 0
|
||||
fi
|
||||
"$BCMCMD_CMD" -n "$unit" -c " ${cmd} " </dev/null 2>&1
|
||||
}
|
||||
|
||||
case "$ACT" in
|
||||
start) SUB="STArt bin_group=${FDR_BIN_GROUP} Interval=${FDR_INTERVAL}" ;;
|
||||
clear) SUB="clear" ;;
|
||||
rdcnt) SUB="Counters" ;;
|
||||
stop) SUB="STOp" ;;
|
||||
esac
|
||||
|
||||
for u in $FDR_UNITS; do
|
||||
_bcm "$u" "$SUB"
|
||||
done
|
||||
|
||||
echo
|
||||
echo "### [$(date '+%F %T')] FDR_${ACT^^}_DONE units: $FDR_UNITS"
|
||||
@@ -0,0 +1,98 @@
|
||||
#!/bin/bash
|
||||
# Turn TX off/on, or show state, for lanes of one Agera3 retimer on the sys and line side.
|
||||
usage() {
|
||||
cat <<USAGE
|
||||
Usage: $0 <asic 0|1> <retimer-addr> <lane_map> <off|on|status> [--method squelch|power] [--force]
|
||||
squelch TX squelch on sys and line side; lanes stay powered (works with the installed agera3)
|
||||
power TX+RX lane power-down, the call SONiC makes on admin down; needs an agera3 with 'power'
|
||||
--force allow 'off' on lanes that receive a signal
|
||||
USAGE
|
||||
exit 1
|
||||
}
|
||||
[ $# -ge 4 ] || usage
|
||||
ASIC=$1; ADDR=$2; MAP=$3; ACT=$4; shift 4
|
||||
METHOD=squelch; FORCE=0
|
||||
while [ $# -gt 0 ]; do
|
||||
case $1 in
|
||||
--method) METHOD=$2; shift 2 ;;
|
||||
--force) FORCE=1; shift ;;
|
||||
*) usage ;;
|
||||
esac
|
||||
done
|
||||
case $ASIC in 0|1) ;; *) usage ;; esac
|
||||
case $ACT in off|on|status) ;; *) usage ;; esac
|
||||
case $METHOD in squelch|power) ;; *) usage ;; esac
|
||||
[[ $ADDR =~ ^0x[0-9a-fA-F]+$ && $MAP =~ ^0x[0-9a-fA-F]{1,2}$ ]] || usage
|
||||
MAPV=$((MAP))
|
||||
[ "$MAPV" -ge 1 ] || usage
|
||||
|
||||
ag() { sudo timeout 30 agera3 "$ASIC" "$ADDR" --no-cleanup "$@" </dev/null 2>&1; }
|
||||
|
||||
if [ "$METHOD" = power ] && ! sudo agera3 -h 2>&1 | grep -q -E '^\s+power '; then
|
||||
echo "agera3 on this system has no 'power' command; use --method squelch"
|
||||
exit 4
|
||||
fi
|
||||
|
||||
lock_mask() {
|
||||
ag rx-pmd-lock get side "$1" lane_map=0xff | awk '$2=="|" && $3=="LOCKED" {m += 2^$1} END {printf "%d", m}'
|
||||
}
|
||||
|
||||
lane_tx() {
|
||||
local lm
|
||||
lm=$(printf '0x%02x' $((1 << $2)))
|
||||
if [ "$METHOD" = squelch ]; then
|
||||
ag squelch get tx "$1" lane_map=$lm | sed -n 's/.*squelch is \([A-Z]*\).*/\1/p' | awk '{print ($1 == "CLEAR") ? "on" : "off"}'
|
||||
else
|
||||
ag power get "$1" lane_map=$lm | awk -v l="$2" '$1 == l && $2 == "|" {print $3}'
|
||||
fi
|
||||
}
|
||||
|
||||
txoff_mask() {
|
||||
local m=0 l s
|
||||
for l in 0 1 2 3 4 5 6 7; do
|
||||
[ $((MAPV >> l & 1)) = 1 ] || continue
|
||||
s=$(lane_tx "$1" $l)
|
||||
case $s in
|
||||
off) m=$((m | 1 << l)) ;;
|
||||
on) ;;
|
||||
*) echo "unknown"; return ;;
|
||||
esac
|
||||
done
|
||||
printf '0x%02x' $m
|
||||
}
|
||||
|
||||
report() {
|
||||
local side
|
||||
for side in sys line; do
|
||||
printf 'asic%s %-6s %-4s lane_map=0x%02x rx_lock=0x%02x tx_off=%s (%s)\n' \
|
||||
"$ASIC" "$ADDR" "$side" "$MAPV" "$(lock_mask $side)" "$(txoff_mask $side)" "$METHOD"
|
||||
done
|
||||
}
|
||||
|
||||
[ "$ACT" = status ] && { report; exit 0; }
|
||||
|
||||
if [ "$ACT" = off ] && [ $FORCE = 0 ]; then
|
||||
live=$(( ($(lock_mask sys) | $(lock_mask line)) & MAPV ))
|
||||
if [ $live != 0 ]; then
|
||||
printf 'REFUSED: asic%s %s lanes 0x%02x receive a signal; use --force to override\n' "$ASIC" "$ADDR" $live
|
||||
exit 2
|
||||
fi
|
||||
fi
|
||||
|
||||
for side in sys line; do
|
||||
if [ "$METHOD" = squelch ]; then
|
||||
ag squelch set tx $side lane_map=$MAP $([ $ACT = off ] && echo enable || echo disable)
|
||||
else
|
||||
ag power set $side lane_map=$MAP $ACT
|
||||
fi | grep -E 'FAIL|Error'
|
||||
done
|
||||
|
||||
want=0x00; [ "$ACT" = off ] && want=$(printf '0x%02x' $MAPV)
|
||||
rc=0
|
||||
for side in sys line; do
|
||||
got=$(txoff_mask $side)
|
||||
printf 'asic%s %-6s %-4s lane_map=0x%02x tx_off=%s expected=%s (%s)\n' "$ASIC" "$ADDR" "$side" "$MAPV" "$got" "$want" "$METHOD"
|
||||
[ "$got" = "$want" ] || rc=3
|
||||
done
|
||||
[ $rc = 0 ] && echo "PASS" || echo "FAIL"
|
||||
exit $rc
|
||||
@@ -0,0 +1,155 @@
|
||||
#!/bin/bash
|
||||
#==============================================================================
|
||||
# Author : ETWen
|
||||
# Date : 20261001
|
||||
# Purpose : Tray ID I2C stress - write a pattern to the Tray ID register on each
|
||||
# bus, read it back and compare. Patterns 0xA5 and 0x5A exercise every
|
||||
# bit in both states (1010_0101 / 0101_1010).
|
||||
# Usage : ./tray_id_stress.sh [-n loops] [-R] [-h]
|
||||
# -n N repeat the whole sequence N times (default 1)
|
||||
# -R do NOT restore the original register value at the end
|
||||
# -h help
|
||||
# Buses / address / register / patterns are set in the block below.
|
||||
#
|
||||
# Exit : 0 = all PASS, 1 = any FAIL or I2C error, 2 = usage
|
||||
#
|
||||
# Version History:
|
||||
# V1.0.0 20261001 Initial Version
|
||||
#==============================================================================
|
||||
|
||||
#------------------------------------------------------------------------------
|
||||
# Settings - edit here
|
||||
#------------------------------------------------------------------------------
|
||||
BUSES=(34 35 38 39) # i2c buses, one Tray ID device each
|
||||
ADDR=0x70 # device address
|
||||
REG=0x02 # Tray ID register
|
||||
PATTERNS=(0xa5 0x5a) # written in this order, each read back and compared
|
||||
RESTORE=1 # 1 = write the original value back when done
|
||||
|
||||
LOOPS=1
|
||||
|
||||
usage() {
|
||||
sed -n '/^# Usage/,/^# Exit/p' "$0" | sed 's/^# \{0,1\}//'
|
||||
}
|
||||
|
||||
while getopts ":n:Rh" opt; do
|
||||
case "$opt" in
|
||||
n) LOOPS="$OPTARG" ;;
|
||||
R) RESTORE=0 ;;
|
||||
h) usage; exit 0 ;;
|
||||
:) echo "ERROR: -$OPTARG needs a value" >&2; usage >&2; exit 2 ;;
|
||||
\?) echo "ERROR: unknown option -$OPTARG" >&2; usage >&2; exit 2 ;;
|
||||
esac
|
||||
done
|
||||
if ! [[ "$LOOPS" =~ ^[1-9][0-9]*$ ]]; then
|
||||
echo "ERROR: -n must be a positive integer (got '$LOOPS')" >&2; exit 2
|
||||
fi
|
||||
for t in i2cset i2cget; do
|
||||
command -v "$t" >/dev/null 2>&1 || { echo "ERROR: $t not found" >&2; exit 2; }
|
||||
done
|
||||
|
||||
# Counters per bus
|
||||
declare -A N_PASS N_FAIL N_ERR ORIG
|
||||
for b in "${BUSES[@]}"; do N_PASS[$b]=0; N_FAIL[$b]=0; N_ERR[$b]=0; ORIG[$b]=""; done
|
||||
|
||||
# Read one byte; prints the value (0xNN) on success, returns 1 on failure.
|
||||
rd() {
|
||||
local out
|
||||
out=$(i2cget -f -y "$1" "$ADDR" "$REG" 2>&1)
|
||||
if [[ $? -ne 0 || ! "$out" =~ ^0x[0-9a-fA-F]{1,2}$ ]]; then
|
||||
echo "$out"; return 1
|
||||
fi
|
||||
echo "$out"
|
||||
}
|
||||
|
||||
TS() { date '+%Y-%m-%d %H:%M:%S'; }
|
||||
|
||||
echo "=========================================================="
|
||||
echo " Tray ID I2C stress $(TS)"
|
||||
echo " buses: ${BUSES[*]} addr $ADDR reg $REG"
|
||||
echo " patterns: ${PATTERNS[*]} loops: $LOOPS restore: $RESTORE"
|
||||
echo "=========================================================="
|
||||
|
||||
#------------------------------------------------------------------------------
|
||||
# Original values (so they can be put back)
|
||||
#------------------------------------------------------------------------------
|
||||
for b in "${BUSES[@]}"; do
|
||||
if v=$(rd "$b"); then
|
||||
ORIG[$b]="$v"
|
||||
printf "[bus %-2s %s reg %s] original value: %s\n" "$b" "$ADDR" "$REG" "$v"
|
||||
else
|
||||
printf "[bus %-2s %s reg %s] original value: READ ERROR (%s)\n" "$b" "$ADDR" "$REG" "$v"
|
||||
fi
|
||||
done
|
||||
echo "----------------------------------------------------------"
|
||||
|
||||
#------------------------------------------------------------------------------
|
||||
# Write / read-back
|
||||
#------------------------------------------------------------------------------
|
||||
for (( loop = 1; loop <= LOOPS; loop++ )); do
|
||||
(( LOOPS > 1 )) && echo "--- loop $loop / $LOOPS ---"
|
||||
for b in "${BUSES[@]}"; do
|
||||
for p in "${PATTERNS[@]}"; do
|
||||
tag=$(printf "[bus %-2s %s reg %s]" "$b" "$ADDR" "$REG")
|
||||
if ! werr=$(i2cset -f -y "$b" "$ADDR" "$REG" "$p" 2>&1); then
|
||||
N_ERR[$b]=$(( N_ERR[$b] + 1 ))
|
||||
echo "$tag write $p -> WRITE ERROR (${werr:-no message}) ERROR"
|
||||
continue
|
||||
fi
|
||||
if ! got=$(rd "$b"); then
|
||||
N_ERR[$b]=$(( N_ERR[$b] + 1 ))
|
||||
echo "$tag write $p -> READ ERROR (${got:-no message}) ERROR"
|
||||
continue
|
||||
fi
|
||||
if (( got == p )); then
|
||||
N_PASS[$b]=$(( N_PASS[$b] + 1 ))
|
||||
echo "$tag write $p -> read $got PASS"
|
||||
else
|
||||
N_FAIL[$b]=$(( N_FAIL[$b] + 1 ))
|
||||
echo "$tag write $p -> read $got FAIL"
|
||||
fi
|
||||
done
|
||||
done
|
||||
done
|
||||
|
||||
#------------------------------------------------------------------------------
|
||||
# Restore
|
||||
#------------------------------------------------------------------------------
|
||||
if (( RESTORE )); then
|
||||
echo "----------------------------------------------------------"
|
||||
for b in "${BUSES[@]}"; do
|
||||
o=${ORIG[$b]}; v=""
|
||||
if [[ -z "$o" ]]; then
|
||||
printf "[bus %-2s] restore skipped: original value was not readable\n" "$b"
|
||||
continue
|
||||
fi
|
||||
if i2cset -f -y "$b" "$ADDR" "$REG" "$o" >/dev/null 2>&1 && v=$(rd "$b") && (( v == o )); then
|
||||
printf "[bus %-2s] restored %s\n" "$b" "$o"
|
||||
else
|
||||
printf "[bus %-2s] RESTORE FAILED: wanted %s, read %s\n" "$b" "$o" "${v:-?}"
|
||||
N_ERR[$b]=$(( N_ERR[$b] + 1 ))
|
||||
fi
|
||||
done
|
||||
fi
|
||||
|
||||
#------------------------------------------------------------------------------
|
||||
# Summary
|
||||
#------------------------------------------------------------------------------
|
||||
per_bus=$(( LOOPS * ${#PATTERNS[@]} ))
|
||||
tp=0; tf=0; te=0
|
||||
echo
|
||||
echo "=========================== Summary =========================="
|
||||
printf "%-6s %-6s %-6s %8s %6s %6s %6s %s\n" "BUS" "ADDR" "REG" "CHECKS" "PASS" "FAIL" "ERROR" "RESULT"
|
||||
for b in "${BUSES[@]}"; do
|
||||
p=${N_PASS[$b]}; f=${N_FAIL[$b]}; e=${N_ERR[$b]}
|
||||
tp=$(( tp + p )); tf=$(( tf + f )); te=$(( te + e ))
|
||||
r=PASS; (( f > 0 || e > 0 || p != per_bus )) && r=FAIL
|
||||
printf "%-6s %-6s %-6s %8s %6s %6s %6s %s\n" "$b" "$ADDR" "$REG" "$per_bus" "$p" "$f" "$e" "$r"
|
||||
done
|
||||
total=$(( per_bus * ${#BUSES[@]} ))
|
||||
overall=PASS; (( tf > 0 || te > 0 || tp != total )) && overall=FAIL
|
||||
printf "%-6s %-6s %-6s %8s %6s %6s %6s %s\n" "TOTAL" "" "" "$total" "$tp" "$tf" "$te" "$overall"
|
||||
echo "=============================================================="
|
||||
echo "Tray ID stress RESULT: $overall ($(TS))"
|
||||
|
||||
[[ "$overall" == PASS ]] && exit 0 || exit 1
|
||||
@@ -0,0 +1,103 @@
|
||||
#!/bin/bash
|
||||
# Apply off/on/status to the unused retimer lanes and TH6 ports listed below, on each ASIC.
|
||||
|
||||
# Same rows apply to both switch boards. lanes: retimer lane_map, sys and line side.
|
||||
# tsc: TH6 TSC as in HW docs and the "#TSCn" labels in th6-helios.config.yml.
|
||||
# th6_ports: BCM shell port name or range; used by th6 rows, and by retimer rows with --th6.
|
||||
UNUSED=$(cat <<'TABLE'
|
||||
# kind target lanes refdes tsc th6_ports note
|
||||
retimer 0x102 0xff U22 23 cd80-cd83 no used ports
|
||||
retimer 0x142 0xff U32 38 cd148-cd151 no used ports
|
||||
retimer 0x21 0xff U39 7 cd16-cd19 no used ports
|
||||
retimer 0x240 0xff U67 54 cd212-cd215 no used ports
|
||||
retimer 0x264 0xff U73 62 cd244-cd247 no used ports
|
||||
retimer 0x48 0xff U82 15 cd48-cd51 no used ports
|
||||
retimer 0x202 0xff U92 46 cd180-cd183 no used ports
|
||||
retimer 0x122 0x30 U18 27 cd111 lanes 4,5 unused
|
||||
retimer 0x248 0x30 U63 58 cd235 lanes 4,5 unused
|
||||
retimer 0x2 0x30 U70 3 cd15 lanes 4,5 unused
|
||||
retimer 0x40 0x30 U75 11 cd47 lanes 4,5 unused
|
||||
retimer 0x162 0x30 U80 42 cd171 lanes 4,5 unused
|
||||
retimer 0x222 0x30 U87 50 cd203 lanes 4,5 unused
|
||||
retimer 0x62 0x30 U96 19 cd79 lanes 4,5 unused
|
||||
th6 TSC31 - - 31 cd112-cd115 direct TH6 TSC, no retimer
|
||||
# th6 TSC34 - - 34 cd139 direct TH6 TSC34 lanes 6,7; down and unused in full rack, not in HW list
|
||||
TABLE
|
||||
)
|
||||
|
||||
DIR=$(cd "$(dirname "$0")" && pwd)
|
||||
usage() {
|
||||
cat <<USAGE
|
||||
Usage: $0 <off|on|status> [--asic 0|1|all] [--method squelch|power] [--th6] [--only <target>] [--force]
|
||||
retimer rows: retimer lanes on sys and line side, via retimer_lanes.sh
|
||||
th6 rows : TH6 ports in the th6_ports column, via the BCM shell
|
||||
--th6 : also act on the th6_ports of retimer rows (TH6 ports feeding those retimer lanes)
|
||||
--only : act on one row, matched by its target column (e.g. 0x102 or TSC31)
|
||||
USAGE
|
||||
exit 1
|
||||
}
|
||||
[ $# -ge 1 ] || usage
|
||||
ACT=$1; shift
|
||||
ASICS="0 1"; METHOD=squelch; TH6=0; ONLY=""; FORCE=""
|
||||
while [ $# -gt 0 ]; do
|
||||
case $1 in
|
||||
--asic) case $2 in all) ASICS="0 1" ;; 0|1) ASICS=$2 ;; *) usage ;; esac; shift 2 ;;
|
||||
--method) METHOD=$2; shift 2 ;;
|
||||
--th6) TH6=1; shift ;;
|
||||
--only) ONLY=$2; shift 2 ;;
|
||||
--force) FORCE=--force; shift ;;
|
||||
*) usage ;;
|
||||
esac
|
||||
done
|
||||
case $ACT in off|on|status) ;; *) usage ;; esac
|
||||
[ -x "$DIR/retimer_lanes.sh" ] || { echo "retimer_lanes.sh not found next to $0"; exit 1; }
|
||||
|
||||
bcm() { docker exec "syncd$1" bcmcmd -t 60 "$2" </dev/null 2>&1 | tr -d '\r'; }
|
||||
ps_state() { bcm "$1" "ps $2" | sed -E 's/\( +/(/' | awk '$1 ~ /^cd[0-9]+\(/ {print $1, $2}'; }
|
||||
|
||||
th6_ports() {
|
||||
local a=$1 act=$2 ports=$3 st
|
||||
st=$(ps_state "$a" "$ports")
|
||||
[ -n "$st" ] || { echo "asic$a th6 $ports: no such ports"; return 3; }
|
||||
if [ "$act" = status ]; then
|
||||
echo "$st" | sed "s/^/asic$a th6 /"
|
||||
return 0
|
||||
fi
|
||||
if [ "$act" = off ] && [ -z "$FORCE" ] && echo "$st" | awk '$2 == "up"' | grep -q .; then
|
||||
echo "REFUSED: asic$a th6 $ports has link up: $(echo "$st" | awk '$2 == "up" {printf "%s ", $1}')"
|
||||
return 2
|
||||
fi
|
||||
bcm "$a" "port $ports enable=$([ "$act" = off ] && echo false || echo true)" >/dev/null
|
||||
sleep 1
|
||||
st=$(ps_state "$a" "$ports")
|
||||
echo "$st" | sed "s/^/asic$a th6 /"
|
||||
if [ "$act" = off ]; then
|
||||
echo "$st" | awk '$2 != "!ena"' | grep -q . && return 3
|
||||
else
|
||||
echo "$st" | awk '$2 == "!ena"' | grep -q . && return 3
|
||||
fi
|
||||
return 0
|
||||
}
|
||||
|
||||
mapfile -t ROWS < <(grep -v -E '^[[:space:]]*(#|$)' <<<"$UNUSED")
|
||||
ok=0; refused=0; failed=0
|
||||
for a in $ASICS; do
|
||||
for row in "${ROWS[@]}"; do
|
||||
read -r kind target lanes refdes tsc ports note <<<"$row"
|
||||
[ -n "$ONLY" ] && [ "$target" != "$ONLY" ] && continue
|
||||
echo "== asic$a $kind $target refdes=$refdes TSC$tsc th6=$ports: $note"
|
||||
rc=0
|
||||
case $kind in
|
||||
retimer)
|
||||
"$DIR/retimer_lanes.sh" "$a" "$target" "$lanes" "$ACT" --method "$METHOD" $FORCE; rc=$?
|
||||
if [ $TH6 = 1 ] && [ "$ports" != "-" ] && [ $rc != 2 ]; then
|
||||
th6_ports "$a" "$ACT" "$ports" || rc=$?
|
||||
fi ;;
|
||||
th6) th6_ports "$a" "$ACT" "$ports"; rc=$? ;;
|
||||
*) echo "unknown kind '$kind'"; rc=1 ;;
|
||||
esac
|
||||
case $rc in 0) ok=$((ok + 1)) ;; 2) refused=$((refused + 1)) ;; *) failed=$((failed + 1)) ;; esac
|
||||
done
|
||||
done
|
||||
echo "== $ACT done: ok=$ok refused=$refused failed=$failed"
|
||||
[ $failed = 0 ]
|
||||
@@ -15,6 +15,10 @@ sendln "show platform voltage"
|
||||
wait prompt_sonic_root
|
||||
sendln "show platform current"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/TH6_SWB0_power_readback.sh"
|
||||
wait prompt_sonic_root
|
||||
sendln "~/Blanton_Script/TH6_SWB1_power_readback.sh"
|
||||
wait prompt_sonic_root
|
||||
sendln "show platform ssdhealth"
|
||||
wait prompt_sonic_root
|
||||
sendln "show platform leak status"
|
||||
|
||||
+44
-1
@@ -1,4 +1,4 @@
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=3' "
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=p31' "
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' "
|
||||
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STArt Interval=30' "
|
||||
@@ -7,6 +7,49 @@ bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STOp' "
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs clear' "
|
||||
|
||||
|
||||
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=p31' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' "
|
||||
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STArt Interval=30' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat Ber' "
|
||||
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STOp' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs clear' "
|
||||
|
||||
//BER SWB0/1
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=p31' "
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' "
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=p31' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs get' "
|
||||
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STArt Interval=30' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STArt Interval=30' "
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat Ber' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat Ber' "
|
||||
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STOp' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbsstat STOp' "
|
||||
bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs clear' "
|
||||
bcmcmd -n 1 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs clear' "
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
bcmcmd -n 0 "port 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 en=0"
|
||||
bcmcmd -n 0 "port 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 en=1"
|
||||
|
||||
bcmcmd -n 1 "port 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 en=0"
|
||||
bcmcmd -n 1 "port 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 en=1"
|
||||
|
||||
|
||||
root@sonic:~# bcmcmd -n 0 -c " dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=3' "
|
||||
dsh -c 'phydiag 1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565 prbs set p=3'
|
||||
drivshell>
|
||||
|
||||
Reference in New Issue
Block a user