docs: Record V1.2.3 in Script A's history and add the release note

Script A: header to V1.2.3 / 2026-09-23; five entries under V1.2.3 for
setup_pmon.ttl, ddr5_temp.sh, hsc_temp_readback.sh, avt_pmpower.sh and
Script 4, with notes on the ~4 s per snapshot, the exec bit, the CRLF in
hsc_temp_readback.sh v1.0.0 and AVT not being shipped.

CLAUDE.md: status to V1.2.3; the PMON temperatures and Script 4's CPU
power in the overview; a commands block for the three new scripts; fix
the stale Script 5 file name and the "last release V1.1.5" line.

ARCHITECTURE.md: Script A ref to V1.2.3; the three scripts in the tree
and in setup_pmon's comment; avt_pmpower.sh in Script 4's row; the git
tag checkbox to V1.2.3.

Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01UniUXkxgCG2Ty74advL8Pd

ARCHITECTURE.md

@@ -136,6 +136,7 @@ Blanton_TTL_Script/
 │   ├── 100G_PRBS.txt                      # 100G PRBS 原始指令（port_prbs_monitor.sh 的來源）
 │   ├── TR518.txt                          # 內建封包測試 tr 518 → blanton_tr518.sh
 │   ├── BER_Test.txt                       # 全機 PRBS BER 指令 → blanton_ber.sh
+│   ├── 100G_dsc_cycle.txt                 # 100G tuning + link 循環 + DSC → bcm_100g_dsc_cycle.sh
 │   ├── Multiphase_{high3,low3,comboA,comboB,Save}.txt  # → blanton_multiphase_margin.sh
 │   ├── Multiphase_Netname                 # 38 條軌的 net 名稱（區塊順序對應）
 │   ├── 100G_Traffic.txt                   # ce0 VLAN 138 打流 → blanton_traffic_linespeed.sh
@@ -161,7 +162,7 @@ Blanton_TTL_Script/
         │
         ├── 4_Blanton_Script_thermal_safety.ttl  # 熱 / 安規：獨立跑，不接 A→B→C
         ├── 5_Blanton_Script_Reboot_Cycle.ttl    # 重開機循環：獨立跑，while 1 無止境（未上機驗證）
-        ├── config.ttl                 # 全域設定：testcase 名、EN_Margin / EN_log / EN_timestamp、
+        ├── config.ttl                 # 全域設定：testcase 名、EN_Margin / EN_TX_FIR / EN_log / EN_timestamp、
         │                              #   風扇與 SWB 宣告、SSD/USB/BMC_USB 壓力秒數、三個 prompt 字串
         ├── hammer/                    # 🚫 gitignored — mlucas ELF binary（~99 MB），DUT image 自帶，
         │                              #   publish.sh 也排除；Script B / Script 4 只負責 chmod +x 後執行
@@ -173,6 +174,7 @@ Blanton_TTL_Script/
         │   ├── pcie_bus.ttl               # lspci -tvvv / -vv
         │   ├── setup_pmon.ttl             # show platform summary/fan/temperature/psustatus/voltage/
         │   │                              #   current/ssdhealth/leak status/leak channels + TPM（11 項）
+        │   │                              #   V1.2.3 起 + ddr5_temp.sh + hsc_temp_readback.sh
         │   ├── show_dmesg.ttl             # dmesg -T 合併 error 正則 + i2c 過濾 + dmesg -C 清空
         │   ├── show_margin_status.ttl     # source margin_status_all.sh（掃 9 顆 LTC2980）
         │   ├── kill_all_process.ttl       # kill $(jobs -p)
@@ -199,7 +201,13 @@ Blanton_TTL_Script/
             ├── mgmt_ping_monitor.sh       # 10G/1G 管理網路 ping 監控（iproute2）
             │                              #   eth0→TARGET_10G、eth1→TARGET_1G，兩張卡同時持續 ping
             ├── port_prbs_monitor.sh       # 100G uplink PRBS 測試（bcmcmd phy diag）
+            │                              #   ⚠️ V1.1.9 起 A/B/C 內註解掉的呼叫已整段刪除，只剩手動執行
             ├── blanton_ber.sh             # 全機 SerDes BER 掃描（phydiag prbs / prbsstat）
+            │                              #   V1.2.2 起含 port 268（100G ce0），summary 每 unit 分 200G/100G/TOTAL
+            ├── bcm_100g_dsc_cycle.sh      # 100G link down/up 循環 + 每輪 DSC 與 retimer TX/RX 讀回（未驗證）
+            ├── bcm_dsc_scan.sh            # 全機 SerDes DSC dump（phydiag <port> dsc，~445 port × 2 unit）
+            │                              #   由 EN_TX_FIR 控制，A 與 C 各掃一次；單次約 10 分鐘
+            ├── bcm_dsc_parse.sh           # DSC raw log → <prefix>_lane.csv / _pm.csv（純 sh + awk）
             ├── blanton_multiphase_margin.sh # 多相 VRM margin（原生 i2c，38 條軌）
             ├── pwr_brick.sh               # PDB / CPB power brick 讀值（VI2C ch4）
             ├── nfc_polling.sh             # NFC tag 背景輪詢 + PASS/FAIL 統計
@@ -208,9 +216,12 @@ Blanton_TTL_Script/
             ├── TH6_SWB0_power_readback.sh # SWB0 19 條軌 V×I + 總功耗
             ├── TH6_SWB1_power_readback.sh # SWB1 同上
             │                              #   ⚠️ 已納入交付，但 A/B/C 的呼叫仍註解掉（bring-up 中）
+            ├── ddr5_temp.sh               # DDR5 DIMM 溫度（SPD5118 @ i2c-5 0x50/0x51，reg 0x31）
+            ├── hsc_temp_readback.sh       # LTC4287 HSC 溫度（i2c-28 0x40/0x45，內/外部感溫）
+            ├── avt_pmpower.sh             # AMD CPU 封裝功耗（AVTCMD pmm get_pmdata；AVT 是 NDA，不隨包）
             ├── usb_target.sh              # 偵測 USB 裝置節點／掛載點（排除系統碟）
             ├── bmc_monitor.sh             # BMC 監控：free -m + I2C 寫入/讀回圖樣測試
-            ├── bmc_monitor_ddr.sh         # ⚠️ 已停用：B/C 內呼叫處已註解，DDR 壓力改走 bgctl + bmc-manager
+            ├── bmc_monitor_ddr.sh         # ⚠️ 已停用：V1.1.9 起 B/C 內的註解區塊已刪除，DDR 壓力走 bgctl + bmc-manager
             │                              #   ↑ 三支都要 chmod +x 才能跑（見 Key Constraints）
             └── LTC2980_Margin_Script/     # 電壓 margin 子專案（另有獨立 repo）
                 ├── margin.sh              # margin_init/status/set/apply_profile/save
@@ -370,10 +381,10 @@ PROFILE_CHANNELS=( "0:high:8" "1:low:8" ... )   # "channel:operation:change_perc
 
 | 模組 | 進入點 | 功能 |
 |------|--------|------|
-| **Script A（Pre-test）** | `1_Blanton_Script_A.ttl` V1.1.8 | root 登入 → `date -s` 對時 → 清 job log → **收掉前一輪殘留**（`hw-test-session finish` → `bgctl reset --yes` → `bgctl stop --all` → `bgctl list` 確認清空）→ `hw-test-session start` → **設定風扇轉速** → **等資料面就緒**（`wait_init.ttl`）→ DUT 清單（boot/version/fwutil/syseeprom/ssdhealth/TPM/NVMe）→ BMC enroll + version/status → source bash 工具 → 清/讀 7 組 PCIe AER + `ras-mc-ctl --summary` → `lspci` → margin → PMON → dmesg → **10G/1G 管理網路 ping** → **NFC 基線**（start → 30s → stop → report）→ 100G uplink 設定與狀態 → **一輪流量基線** → `show uptime` |
-| **Script B（Stress）** | `2_Blanton_Script_B.ttl` | **V1.1.8 起 `mlucas-avx2 -cpu 0:15` 由 `systemd-run --unit=mlucas-amm`（`Type=exec`、`Restart=always`）啟動，不再是 shell 的 `&` 背景 job** + `bgctl run` 的 `memtester` / SSD / USB 壓力（v1.1.7 起 SSD/USB 的 `--runtime`/`--passes` 讀 `config.ttl` 的 `SSD_RUNTIME`/`SSD_COUNT`、`USB_RUNTIME`/`USB_COUNT`；BMC memtester 不帶次數 = 跑到被停） + BMC DDR（`bmc-manager run memtester`）→ BMC USB net test（探測 cdc_ncm 介面，`systemd-run` 掛 `BMC_USB_RUNTIME` 秒的 ping，V1.1.8 前寫死 4 小時）→ 啟動 mgmt ping 監控 → **啟動 NFC 輪詢** → `jobs` / `systemctl is-active mlucas-amm` / `bgctl list` → traffic（依 `SWB_UNIT`）→ `while 1` 每輪 PMON + `bgctl list`/`jobs`/`systemctl is-active mlucas-amm` + `pause 60`（**V1.1.4 起 margin 不在迴圈內**）|
-| **Script C（Post-test）** | `3_Blanton_Script_C.ttl` | `kill $(jobs -p)` + **`systemctl stop mlucas-amm`**（systemd unit 不是 shell job，`jobs -p` 抓不到）+ `bgctl stop --all` / `reset` + 停 BMC USB unit、mgmt ping 與 **NFC 輪詢** → PMON + dmesg → 7 組 AER + `ras-mc-ctl` → BMC USB `journalctl` **寫進 `log/bmc_usb_net.log`**（不再印在 console） → `ip -s link show eth0/eth1` → `cat` mlucas log（並 `cp` 進 job 目錄一起帶走）→ **NFC `report`** → traffic `stop` + `report` → **BER 掃描**（依 `SWB_UNIT`）→ NVMe 健康 → `show reboot-cause` → **margin 掃描**（`EN_Margin`，V1.1.4 由 Script B 移來）→ `uptime` → **job log 複製到 USB（帶時戳）** → `exit` + wait『Script done』→ `hw-test-session finish` |
-| **Script 4（Thermal / Safety）** | `4_Blanton_Script_thermal_safety.ttl` | **獨立腳本，不接 A→B→C。** Script A 式的環境建立（登入 / session / 風扇 / `wait_init` / DUT 清單 / BMC / PCIe 清除 / `pcie_bus` / PMON / dmesg）→ **滿載**（`mlucas-avx2 -cpu 0:15`，V1.1.8 起與 Script B 同樣掛成 `mlucas-amm` systemd unit + `blanton_tr518.sh start`）→ `while 1`：PMON + `TH6_SWB0/1_power_readback.sh` + `bgctl list` / `jobs` / `systemctl is-active mlucas-amm`，`pause 60`。**沒有收尾段** —— 中斷後 DUT 仍在 `port cd lb=mac` / `l2 learn off` / `test mode nr=yes`，且 CPU 仍滿載，要手動 `blanton_tr518.sh stop` + `systemctl stop mlucas-amm` |
+| **Script A（Pre-test）** | `1_Blanton_Script_A.ttl` V1.2.3 | root 登入 → `date -s` 對時 → 清 job log → **收掉前一輪殘留**（`hw-test-session finish` → `bgctl reset --yes` → `bgctl stop --all` → `bgctl list` 確認清空）→ `hw-test-session start` → **設定風扇轉速** → **等資料面就緒**（`wait_init.ttl`）→ DUT 清單（boot/version/fwutil/syseeprom/ssdhealth/TPM/NVMe）→ BMC enroll + version/status → source bash 工具 → 清/讀 7 組 PCIe AER + `ras-mc-ctl --summary` → `lspci` → margin → PMON → dmesg → **10G/1G 管理網路 ping** → **NFC 基線**（start → 30s → stop → report）→ 100G uplink 設定與狀態 → **BER 基線掃描**（依 `SWB_UNIT`，V1.2.1 新增）→ **一輪流量基線** → **SerDes DSC 基線**（`EN_TX_FIR`）→ `show uptime` |
+| **Script B（Stress）** | `2_Blanton_Script_B.ttl` | **V1.1.8 起 `mlucas-avx2 -cpu 0:15` 由 `systemd-run --unit=mlucas-amm`（`Type=exec`、`Restart=always`）啟動，不再是 shell 的 `&` 背景 job** + `bgctl run` 的 `memtester` / SSD / USB 壓力（v1.1.7 起 SSD/USB 的 `--runtime`/`--passes` 讀 `config.ttl` 的 `SSD_RUNTIME`/`SSD_COUNT`、`USB_RUNTIME`/`USB_COUNT`；BMC memtester 不帶次數 = 跑到被停） + BMC DDR（`bmc-manager run memtester`）→ BMC USB net test（探測 cdc_ncm 介面，`systemd-run` 掛 `BMC_USB_RUNTIME` 秒的 ping，V1.1.8 前寫死 4 小時）→ 啟動 mgmt ping 監控 → **啟動 NFC 輪詢** → `jobs` / `systemctl is-active mlucas-amm` / `bgctl list` → traffic（依 `SWB_UNIT`）→ `while 1` 每輪 PMON + `bgctl list`/`jobs`/`systemctl is-active mlucas-amm` + `sleep 60`（**V1.1.4 起 margin 不在迴圈內**；V1.2.0 起等待走 DUT 端 `sleep` 而非 macro 端 `pause`）|
+| **Script C（Post-test）** | `3_Blanton_Script_C.ttl` | `kill $(jobs -p)` + **`systemctl stop mlucas-amm`**（systemd unit 不是 shell job，`jobs -p` 抓不到）+ `bgctl stop --all` / `reset` + 停 BMC USB unit、mgmt ping 與 **NFC 輪詢** → PMON + dmesg → 7 組 AER + `ras-mc-ctl` → BMC USB `journalctl` **寫進 `log/bmc_usb_net.log`**（不再印在 console） → `ip -s link show eth0/eth1` → `cat` mlucas log（並 `cp` 進 job 目錄一起帶走）→ **NFC `report`** → traffic `stop` + `report` → **SerDes DSC 收尾**（`EN_TX_FIR`）→ **BER 掃描**（依 `SWB_UNIT`）→ NVMe 健康 → `show reboot-cause` → **margin 掃描**（`EN_Margin`，V1.1.4 由 Script B 移來）→ `uptime` → **job log 複製到 USB（帶時戳）** → `exit` + wait『Script done』→ `hw-test-session finish` |
+| **Script 4（Thermal / Safety）** | `4_Blanton_Script_thermal_safety.ttl` | **獨立腳本，不接 A→B→C。** Script A 式的環境建立（登入 / session / 風扇 / `wait_init` / DUT 清單 / BMC / PCIe 清除 / `pcie_bus` / PMON / dmesg）→ **滿載**（`mlucas-avx2 -cpu 0:15`，V1.1.8 起與 Script B 同樣掛成 `mlucas-amm` systemd unit + `blanton_tr518.sh start`）→ `while 1`：PMON + `TH6_SWB0/1_power_readback.sh` + `avt_pmpower.sh`（CPU 封裝功耗，V1.2.3）+ `bgctl list` / `jobs` / `systemctl is-active mlucas-amm`，`pause 60`。**沒有收尾段** —— 中斷後 DUT 仍在 `port cd lb=mac` / `l2 learn off` / `test mode nr=yes`，且 CPU 仍滿載，要手動 `blanton_tr518.sh stop` + `systemctl stop mlucas-amm` |
 | **Script 5（Reboot Cycle）** | `5_Blanton_Script_Reboot_Cycle.ttl` | **獨立腳本，不接 A→B→C。** `while 1`：登入 → `sudo -i` → 對時 → 風扇 → **Check Pt1~Pt13**（DUT/BMC info、mgmt ping、NFC、SSD、USB、BMC USB、port status + 15s traffic、BER、NVMe、platform data、dmesg i2c、PCIe error counters）→ `show uptime` → `reboot` → `wait "Booting in blind mode"`。`cnt_cycle` 每輪 +1 印在標頭。**沒有結束條件** —— 要停就關掉 Tera Term 的 macro。**尚未上機驗證** |
 | **SWB loopback 流量** | `blanton_traffic_linespeed <sub> [-u 0\|1\|all]` | `init`（VLAN 30..137，成對 `cdN`/`cdN+32`）→ `clear` → `start`（`tx 200 length=324 PatternRandom=yes`，v0.7.0 起）→ `stop` → `report`（per-pair TX/RX 交叉比對 PASS/FAIL）；另有 `ps`（link/speed）與 `run`（一條龍）。**V0.6.0 起含 100G uplink `ce0`**（VLAN 138）：它沒有 loopback 對象，靠 **ingress mirror 打回自己**維持循環，`report` 最後一列就是它，底下再接一份跨 unit summary |
 | **FPGA 暫存器存取** | `cb_fpga <fn> <addr> [data]`、`fpga_rescan` | pcimem 打 `resource0` + BAR 相對 offset，32-bit word；BDF 於 source 時自動偵測；`pmc/icb/swb0/swb1_fpga` 走 VSPI 窗口 |
@@ -386,9 +397,11 @@ PROFILE_CHANNELS=( "0:high:8" "1:low:8" ... )   # "channel:operation:change_perc
 | **Margin 寫 NVM** | `margin_save` / `margin_save all` / `margin_save blanton` | ⚠️ 永久寫入。`0x15` 送 PMBus **send-byte**（不帶 data byte）。`all` = 依 `settings/` 走 9 顆、跑完還原原本載入的板子；`blanton` = 本平台捷徑，18 顆全走原生 i2c bus（`MARGIN_BLANTON_STORE` 表），不需 `margin_init`。每筆之間 `MARGIN_STORE_SETTLE`（0.5s），工具**不 poll busy bit** |
 | **管理網路 ping** | `mgmt_ping_monitor.sh {start\|stop\|status\|fg\|tail\|clear\|summary}` | 一輪 = 10G leg + 1G leg，各自 `ip address/route replace` 後 `ping -I <if>` 打自己的對端；兩張卡都保持 up。每 leg 記 `ip -s link show` 與該卡的 TX/RX packet delta，另出一行可 grep 的 `RESULT` |
 | **BMC 監控** | `bmc_monitor.sh {start\|stop\|status\|fg\|tail\|clear}` | 由 host 端 `bmc-manager run` 週期取樣 `free -m`，另加一組 **I2C 寫入/讀回圖樣測試**（bus 1、addr 0x41、offset 0x00C0，寫 `55AA55AA` 讀回、再寫 `AA55AA55` 讀回）。B 啟動、C 停止並 `cat log/bmc_poll.log` |
-| **BMC DDR 壓力** | `bmc_monitor_ddr.sh` | ⚠️ **已停用** —— B/C 內呼叫處已註解，改由 `bgctl run bmc-manager run memtester` 取代。檔案保留未刪 |
-| **100G PRBS** | `port_prbs_monitor.sh {start [both\|a\|b]\|stop\|status\|report\|clear}` | 兩個 uplink 各一個 worker，可同時或單獨跑。setup（`lpmode off` → `prbs set` → `prbsstat STArt`）→ 週期 `prbs get`（判定）+ `prbsstat Ber`（只記錄）→ teardown（`STOp` + `prbs clear`）。輸出含 `PRBS OK!` 才算 PASS。**⚠️ A/B/C 的呼叫目前註解掉** |
-| **SerDes BER 掃描** | `blanton_ber.sh {init\|clear\|start\|stop\|report} [-u 0\|1\|all]` | 全機每個對接 port 的 PRBS BER：`prbs set p=3` + `prbs get`（確認每條 lane 都鎖上）→ `prbsstat STArt Interval=30` →（等一個 interval）→ `prbsstat Ber` → `STOp` → `prbs clear`。`report` 一列一條 lane，**BER < 1e-6 才 PASS**，最後跨 unit 的 summary 帶最差 lane。⚠️ PRBS 期間 link 顯示 DOWN、不過流量 |
+| **BMC DDR 壓力** | `bmc_monitor_ddr.sh` | ⚠️ **已停用** —— V1.1.9 起 B/C 內的註解區塊已刪除，改由 `bgctl run bmc-manager run memtester` 取代。檔案保留未刪 |
+| **SerDes DSC 擷取** | `bcm_dsc_scan.sh [-u 0\|1] [-f <name>] [-F] [-n] [-C]` + `bcm_dsc_parse.sh -i <log> -o <prefix>` | `bcmcmd -n <unit> -c "dsh -c 'phydiag <port> dsc'"` 掃全清單（1 個 100G + 445 個 200G port）× 2 unit，raw log 寫進 `<script_dir>/log` 再 `cp` 到 `/host/hw-eval/jobs`。`-f` 支援 `%u` / `%t`；沒帶 `%u` 時自動插 `_u0`/`_u1`。成功與否**不看 `bcmcmd` 的 exit code**，改比對 `SERDES DISPLAY DIAG DATA END` 數量 + 實際迭代筆數，結尾印 `### DSC_SCAN_DONE rc=<n>`。parse 端輸出 `_lane.csv`（每 lane：TXEQ/RXFFE/DFE/EYE/SNR）與 `_pm.csv`（每 pm_id：溫度/PLL/lane 數/統計）。**由 `EN_TX_FIR` 控制，預設關** |
+| **100G PRBS** | `port_prbs_monitor.sh {start [both\|a\|b]\|stop\|status\|report\|clear}` | 兩個 uplink 各一個 worker，可同時或單獨跑。setup（`lpmode off` → `prbs set` → `prbsstat STArt`）→ 週期 `prbs get`（判定）+ `prbsstat Ber`（只記錄）→ teardown（`STOp` + `prbs clear`）。輸出含 `PRBS OK!` 才算 PASS。**⚠️ V1.1.9 起 A/B/C 內的註解呼叫已刪除，只能手動跑** |
+| **SerDes BER 掃描** | `blanton_ber.sh {init\|clear\|start\|stop\|report} [-u 0\|1\|all]` | 全機每個對接 port 的 PRBS BER：`prbs set p=3` + `prbs get`（確認每條 lane 都鎖上）→ `prbsstat STArt Interval=30` →（等一個 interval）→ `prbsstat Ber` → `STOp` → `prbs clear`。`report` 一列一條 lane，**BER < 1e-6 才 PASS**，最後跨 unit 的 summary 帶最差 lane。⚠️ PRBS 期間 link 顯示 DOWN、不過流量。V1.2.1 起 Script A 與 Script C 各跑一次（A 在流量之前、C 在流量報表之後），夾住 soak。**V1.2.2（腳本 v1.1.0）起清單納入 port 268（100G uplink ce0）**，summary 每個 unit 拆成 200G ports / 100G p268 / TOTAL 三列；某組零 lane 算 FAIL |
+| **100G link 循環 + DSC** | `bcm_100g_dsc_cycle.sh <cycles> [-d] [-T] [-P] [-n]` | tuning（`docker pause gbsyncd*` → `serdes-tx-set sys 0..7` → 每 lane `tx_taps set`）一次，之後每輪：`port 268 en=0` → 輪詢 `bcmcmd ps 268` 等 `!ena` → `en=1` → 等 `up` → 兩個 unit 的 `phydiag 268 dsc` + `serdes-tx-get`/`serdes-rx-get sys 0..7`。log 一次執行一份（`~/dsc_log/`），每輪一段 `### TEST CYCLE n/N`，結尾 `### DSC_CYCLE_DONE rc=<n>`。**全 ASCII 輸出**（DUT console 會把 UTF-8 弄成亂碼）。⚠️ 尚未上機驗證 |
 | **TR518 負載** | `blanton_tr518.sh {start\|stop} [-u 0\|1\|all]` | `port cd lb=mac` → `l2 learn off` → `test mode nr=yes` → `tr 518 ... testphase=1`，然後 settle `TR_SETTLE_SEC`（120s）再讓人量功耗。`stop` 只送 `port cd lb=none`（照 `TR518.txt`），L2 學習與 test mode **不會還原**，`TR_RESTORE_*=1` 才會 |
 | **PDB / CPB brick** | `pwr_brick.sh show [-r]` | 5 顆 brick 的 Vin / Iin / Vout / Iout / Temp（SWB0 `0x62`/`0x63`、SWB1 `0x60`/`0x61`、CPB `0x26`）。四顆 ADPM12200 **每個量各自一個 PMBus PAGE**（Vin 9、Iin 10、Vout 2、Iout 14、Temp 18），讀之前一定要先寫 PAGE —— `blanton_pwr_data.sh` 完全沒寫，所以整張 PDB 表都是 NA。換算用手冊 DIRECT 公式 `X=(1/m)(Y×10⁻ᴿ−b)`。每個值重讀到通過三道檢查為止（非 `0xFFFF`、非 `0x0000`、落在合理範圍）—— 這條匯流排**只壞高位元組**，`11.98 V` 會變成 `32.00 V`，全一過濾擋不住 |
 | **SWB 軌功耗** | `TH6_SWB{0,1}_power_readback.sh` | 讀 `show platform voltage/current` **各一次**，19 條軌 V×I 與總功耗。舊版每軌各讀一次（38 次呼叫、每軌不同時刻），總和是不同瞬間的加總 |
@@ -510,6 +523,11 @@ pwr_data
     `vlan create` 的 `Entry exists`（重跑 init）與 `vlan remove` 的 `not found`（init 前先 stop）
     當良性情況分開計數。另外 `bcmcmd` 一律以 `</dev/null` 執行 ——
     否則它會吃掉 while 迴圈的 stdin，導致**只有第一個 VLAN 被設定**（V0.3.1 修的 bug）。
+    **2026-09-07 `bcm_dsc_scan.sh` 又踩了同一個坑**（port 清單走 stdin，445 個 port 只掃了 1 個），
+    而且因為 `### PORT` marker 與 dsc 區塊數量一起變少，原本的比對檢查完全看不出來、`rc=0`。
+    修法：迴圈改讀 fd 3（`done 3< "$PORTFILE"`）+ `bcmcmd ... < /dev/null`，再加一道
+    「實際迭代筆數 == 清單筆數」的獨立檢查。**寫任何餵檔案給 `while` 又在裡面呼叫 `bcmcmd` 的迴圈，
+    都要假設它會讀 stdin；而且完整性檢查不能只比對兩個會一起變少的數字。**
 11. **DUT 密碼不得進 git**：`1_Blanton_Script_A.ttl` 目前的 `sendln "YourPaSsWoRd"` 是 placeholder，
     實際帳密必須放 `secret/config_secret.ttl`（gitignored）並由 `config.ttl` include。
 12. **`.sh` / `.conf` 必須是 LF**：CRLF 的 shell script 在 SONiC 上直接掛
@@ -549,8 +567,15 @@ pwr_data
     ⚠️ **`4_Blanton_Script_thermal_safety.ttl` 用同一個 `mlucas-amm` unit，但它沒有收尾段**，
     所以那行 `systemctl stop mlucas-amm` 必須由測試員手動下 —— 這是 Script 4 目前
     唯一一個「不下就會延續到下一輪」的負載。
-18. **`config.ttl` 少一個變數會讓 macro 當場中止**，不是當成 0。V1.1.8 新增 `EN_timestamp`
-    （Script A `logopen` 的第 5 個參數）與 `BMC_USB_RUNTIME`（Script B 的 ping unit）。
+18. **`pause` 停的是 macro，`sleep` 停的是 DUT。** V1.2.0 起 A/B/C 的等待一律改成
+    `sendln "sleep N"` + `wait prompt_sonic_root`。`pause N` 期間 macro 不理會 DUT，shell 是閒著的，
+    等於用猜的估上一個指令要跑多久 —— DUT 一忙就會提早往下送指令；改成 DUT 端 `sleep` 之後，
+    prompt 回來才繼續，兩邊不可能走散，而且這段等待會帶時戳進 log，事後看得出哪一輪跑久了。
+    ⚠️ **Script 4 與 Script 5 尚未轉換，仍在用 `pause`**；B/C 開頭的 `pause 1` 也保留
+    （它在登入前執行，沒有 prompt 可等）。
+19. **`config.ttl` 少一個變數會讓 macro 當場中止**，不是當成 0。V1.1.8 新增 `EN_timestamp`
+    （Script A `logopen` 的第 5 個參數）與 `BMC_USB_RUNTIME`（Script B 的 ping unit）；
+    V1.2.0 再加 `EN_TX_FIR`（A/C 的 DSC 掃描與 C 的四行 `cp`，預設 0）。
     只更新 `.ttl` 卻沿用舊的 `config.ttl`，Script A 會停在 `logopen` 那一行。
     另外 **時間戳的「格式」不在 macro 裡** —— 它在 Tera Term 的
     Setup → Additional settings → Log，存在那台電腦的 `TERATERM.INI`，會跟著 PC 而不是跟著腳本走。
@@ -787,7 +812,7 @@ margin status、全部 VRM 軌的 Vin/Vout/Iout/Temp、CB + ICB 溫感讀值，
 - [ ] `CHANGELOG.md`：延續三支腳本頂端的 Version History，集中成一份
 - [ ] 三支腳本的 header 版號與 `CHANGELOG.md` 對齊，`config.ttl` 加 `script_version` 並寫進 log 開頭
 - [ ] `docs/TTL_Script_Blanton_Status_*.xlsx` 更新為全 OK，或把剩餘項目移進 Future Extensions
-- [x] 打 git tag，push `nas` + `gitea`（已至 `V1.1.8`；`publish/` 依 Script A 檔頭版號打包）
+- [x] 打 git tag，push `nas` + `gitea`（已至 `V1.2.3`；`publish/` 依 Script A 檔頭版號打包）
 
 **驗收條件：** 從 zip 解壓到一台乾淨的測試 NB，照 README 操作，不看原始碼就能完成一輪 A→B→C
 並產出 summary；`publish/` 內容與 git tag 一致。
@@ -821,14 +846,23 @@ margin status、全部 VRM 軌的 Vin/Vout/Iout/Temp、CB + ICB 溫感讀值，
   Script A 既不往下走也不報錯。可加最大重試次數 + `messagebox` 提示。
 - **腳本的執行權**：`mgmt_ping_monitor.sh` 與 `bmc_monitor.sh`（以及已停用的 `bmc_monitor_ddr.sh`）需人工 `chmod +x`。
   可在 Script B 起它之前補一行（比照既有的 `chmod +x ~/hammer/tools/amd/mlucas-avx2`），或在 publish 時處理。
-- **`bmc_monitor_ddr.sh` 已停用**：B/C 內的呼叫已註解，DDR 壓力改由 `bgctl run bmc-manager run memtester`
-  取代。檔案還留在 repo，待確認不再需要後刪除，或在檔頭標註停用。
+- **`bmc_monitor_ddr.sh` 已停用**：V1.1.9 起 B/C 內那段註解掉的呼叫已刪除，DDR 壓力由
+  `bgctl run bmc-manager run memtester` 取代。檔案還留在 repo，待確認不再需要後刪除，或在檔頭標註停用。
   （`bmc_monitor.sh` 已於 2026-08-25 重新啟用，並加上 I2C 寫入/讀回圖樣測試。）
 - **`rm /host/hw-eval/jobs/*` 清不掉子目錄**：Script A 用的是不帶 `-r` 的 `rm`，但 Script C
   是 `cp -r` 那個目錄，代表裡面可能有子目錄。清不乾淨的話，上一輪的 job log 會被當成這輪的一起
   複製到 USB。要確認 `bgctl` 的產出結構，必要時改成 `rm -rf .../jobs/*`。
-- **100G PRBS 尚未接進 A/B/C**：`port_prbs_monitor.sh` 已隨包交付、可手動執行，但三支腳本裡的呼叫
-  都還註解著（bring-up 中）。要啟用時記得 PRBS 期間 link 會顯示 down，`stop` 之後才會回來。
+- **100G PRBS 已從 A/B/C 移除**：`port_prbs_monitor.sh` 仍隨包交付、仍可手動執行，但 V1.1.9 起
+  三支腳本裡那些註解掉的呼叫已整段刪除（連同 Script C 的 `bmc_monitor_ddr.sh` 區塊）。
+  要接回去得重寫，不是把註解拿掉。啟用時記得 PRBS 期間 link 會顯示 down，`stop` 之後才會回來。
+- **DSC 擷取預設是關的**：`EN_TX_FIR = 0`，所以出貨設定不會跑 `bcm_dsc_scan.sh`。
+  開啟後 Script A 與 Script C 各掃一次、整輪多約 20 分鐘；只要單邊資料可以在腳本裡改成 `-u 0`。
+  掃描本身是唯讀（`phydiag ... dsc` 不改 SerDes 設定），但**它與 `blanton_ber.sh` /
+  `blanton_traffic_linespeed` / `blanton_tr518.sh` 一樣都在動同一批 port，不要同時跑**。
+- **`bcm_100g_dsc_cycle.sh` 尚未上機驗證**：`port en=0/1` 之後 link 多久會動、以及
+  `docker pause gbsyncd*` 期間的影響，都要上機才知道。等待是讀 SDK（`bcmcmd ps <port>`）而不是
+  `show interfaces status`，所以理論上不受 gbsyncd 暫停影響，但沒實測過。
+  結束時（含 Ctrl-C）會自動 `docker unpause`，`RESUME_GBSYNCD=0` 可關掉。
 - **Script 5（Reboot Cycle）尚未上機驗證**：`5_Blanton_Script_Reboot_Cycle.ttl` 隨 V1.1.7 交付，
   但還沒在真 DUT 上跑過一輪完整循環。兩個要現場確認的點：`wait "Booting in blind mode"` 是否
   真的在每一版開機訊息裡出現（沒出現就會永遠等下去，而且沒有 `timeout` 保護）；以及每輪重跑
@@ -892,9 +926,22 @@ margin status、全部 VRM 軌的 Vin/Vout/Iout/Temp、CB + ICB 溫感讀值，
 - **margin 在 soak 期間不再取樣**（V1.1.4）：只剩 Script A 的起始值與 Script C 的結束值。
   漂移發生在中間就看不到了。若要恢復，比較好的做法是在 B 的迴圈內每 N 輪才掃一次，
   而不是每輪都掃。
-- **`blanton_ber.sh` 的 `sleep 30` 與 `BER_INTERVAL` 是兩處要同步改的數字**：Script C 寫死
-  `sendln "sleep 30"`，腳本預設 `BER_INTERVAL=30`。改一邊沒改另一邊，report 會讀到還沒累積完
-  一個 interval 的數字，而且不會有任何警告。
+- ✅ **`blanton_ber.sh` 不再把 lane 的量測結果當成 shell 錯誤**（v1.1.1，2026-09-15）：
+  `prbs get` 每條 lane 一行，沒鎖上的會印 `PRBS Error!`，而錯誤樣式是拿
+  `grep -i 'ERROR|Invalid|...'` 掃整份輸出的 —— 於是正常的 init 會報「the BCM shell rejected」，
+  而且提早 return，**把「哪幾條 lane 沒鎖」這個真正有用的資訊吞掉**。現在 per-lane 行排除在
+  掃描外、改成大小寫敏感、真正的拒絕會把該行印出來。
+  ⚠️ **這類「完整性檢查自己看不到失敗」的錯在這個 repo 已經出現三次**
+  （`bcm_dsc_scan.sh` v1.3.0 數 marker、`blanton_ber.sh` v1.1.1、以及 power cycle 報告的
+  ping 解析把 100% 丟包當成「沒資料」）。寫檢查時要問：**失敗長什麼樣，這段程式碼看得到嗎？**
+- **`blanton_ber.sh` 的 `sleep 30` 與 `BER_INTERVAL` 是兩處要同步改的數字**：Script A（V1.2.1 起）
+  與 Script C 都寫死 `sendln "sleep 30"`，腳本預設 `BER_INTERVAL=30`。改一邊沒改另一邊，report 會
+  讀到還沒累積完一個 interval 的數字，而且不會有任何警告。現在有**三處**要一起改。
+- **Script A 的 BER `clear` 與第一輪流量之間沒有 settle**：V1.2.1 把 BER 掃描放在流量**之前**，
+  而 PRBS 是把 lane 拉出正常運作、`clear` 才放回去的。Script A 的 `blanton_ber.sh clear` 之後
+  緊接著就是 `blanton_traffic_linespeed ps` / `init`，中間沒有等待；Script C 的 BER 在流量報表
+  之後，沒有這個順序。上機時比對兩份 traffic report —— Script A 有 NA/FAIL 而 Script C 沒有，
+  就是 lane 尚未回穩，在 `clear` 後加一個 `sleep` 即可。**尚未上機驗證。**
 - **`ce0` 的 ingress mirror 尚未上機驗證**：`mirror port ce0 Mode=Ingress DestPort=ce0` 這條路是
   推論出來的（鏡像複本不受 egress filter 的 source-port knockout 限制），語法取自 DUT 的
   `help mirror`，但**還沒證明硬體真的接受 destport == srcport**。驗證方式是隔 10 秒看兩次

CLAUDE.md

@@ -9,30 +9,38 @@ DUT 端的取數能力由一組 **bash 工具庫** 提供（CB FPGA `pcimem` →
 
 完整架構見 [ARCHITECTURE.md](ARCHITECTURE.md)。
 
-**目前狀態（2026-09-06）**：Script A 為 **V1.1.8**（A 集中記錄所有 TTL 的變更）。涵蓋
+**目前狀態（2026-09-23）**：Script A 為 **V1.2.3**（A 集中記錄所有 TTL 的變更）。涵蓋
 PCIe AER / DDR EDAC / PMON+TPM / 電壓 margin（9 顆 LTC2980）/ SWB loopback 線速流量 /
 10G+1G 管理網路 ping / BMC DDR 與 USB / NVMe 健康，壓力層走平台的 `bgctl`。
 switch unit 數量由 `config.ttl` 的 `SWB_UNIT0` / `SWB_UNIT1` 宣告，風扇轉速由 `FAN_SPEED` 指定
 （預設 100 = 全速；soak 是熱測試，散熱不該是變因）。
 測試 job log 收在 DUT 的 `/host/hw-eval/jobs/`，Script C 結束時掛好 USB 再帶時戳複製到 `/mnt/usb/`。
-100G PRBS（`port_prbs_monitor.sh`）已隨包交付，但 **A/B/C 的呼叫仍註解掉**，還在 bring-up。
-Script B 的 soak 迴圈每輪印 `bgctl list` + `jobs` + `systemctl is-active mlucas-amm`，並 `pause 60`
-（V1.0.10 之前完全沒有 pause）。V1.1.8 起 AMD CPU 壓力（`mlucas-avx2`）由 `systemd-run` 掛成
+100G PRBS（`port_prbs_monitor.sh`）已隨包交付、可手動執行，但 **V1.1.9 起 A/B/C 裡註解掉的呼叫已整段刪除**，
+要接回去得重寫（`bmc_monitor_ddr.sh` 在 Script C 的註解區塊同時移除）。
+V1.1.9 新增 **SerDes DSC 擷取**：`bcm_dsc_scan.sh`（DUT 端，`phydiag <port> dsc` 掃全機 ~445 port × 2 unit，
+約 10 分鐘）由 Script A 與 Script C 各跑一次夾住 soak，`bcm_dsc_parse.sh`（Host 端）把 raw log 轉成
+`_lane.csv` / `_pm.csv`。**由 `config.ttl` 的 `EN_TX_FIR` 控制，預設 0（關）** —— 開了整輪測試多 ~20 分鐘。
+Script B 的 soak 迴圈每輪印 `bgctl list` + `jobs` + `systemctl is-active mlucas-amm`，並 `sendln "sleep 60"`
+（V1.0.10 之前完全沒有間隔；V1.2.0 起 A/B/C 的等待一律改成 DUT 端 `sleep` 而非 macro 端 `pause`）。V1.1.8 起 AMD CPU 壓力（`mlucas-avx2`）由 `systemd-run` 掛成
 `mlucas-amm` transient unit（`Restart=always`），不再是 shell 的 `&` 背景 job —— 掉線也不會停，
 Script C 用 `systemctl stop mlucas-amm` 收掉並把 log 複製到隨身碟。
-V1.1.0 新增全機 SerDes BER 掃描（`blanton_ber.sh`，**Script C 已接**，依 `SWB_UNIT` 分支）、
+V1.1.0 新增全機 SerDes BER 掃描（`blanton_ber.sh`，依 `SWB_UNIT` 分支）；**V1.2.1 起 Script A 也接了一次**，
+**V1.2.2 起清單納入 port 268（100G uplink，ce0）**，summary 每個 unit 拆成「200G ports / 100G p268 / TOTAL」三列；
+在第一輪流量之前取基線，與 Script C 流量報表之後的收尾掃描一起夾住 soak（同 DSC 的做法）。另有
 TR518 負載（`blanton_tr518.sh`，**TTL 尚未接**）、SWB 軌功耗（`TH6_SWB{0,1}_power_readback.sh`），
 線速流量也納入 100G `ce0`（VLAN 138，靠 ingress mirror 維持循環）。
 Script A 開頭會先收掉前一輪殘留（`hw-test-session finish` + `bgctl reset/stop --all`），
 再 `bgctl list` 確認沒有 job 留著佔資源。
 NFC tag 讀取由 `nfc_polling.sh` 背景輪詢（A 做基線、B 起、C 停並 report）。
 另有 **`4_Blanton_Script_thermal_safety.ttl`**（熱 / 安規，**獨立跑不接 A→B→C**，滿載後每分鐘
-取 PMON + 兩片 SWB 的軌功耗；**沒有收尾段**，中斷後要手動 `blanton_tr518.sh stop`）。
-以及 **`5_Blanton_Script_Reboot_Cycle.ttl`**（重開機循環，**獨立跑不接 A→B→C**：登入 → 風扇 →
+取 PMON + 兩片 SWB 的軌功耗 + **AMD CPU 封裝功耗**（`avt_pmpower.sh`，V1.2.3）；**沒有收尾段**，中斷後要手動 `blanton_tr518.sh stop`）。
+**V1.2.3 起 PMON 快照（`utils/setup_pmon.ttl`）多了 DDR5 DIMM 溫度（`ddr5_temp.sh`）與 LTC4287 HSC 溫度
+（`hsc_temp_readback.sh`）**，A/B/C/4/5 全部吃到；HSC 那支每次約 +4 秒。
+以及 **`5_Blanton_Script_Boot_Cycle.ttl`**（重開機循環，**獨立跑不接 A→B→C**：登入 → 風扇 →
 Check Pt1~Pt13 → `reboot` → `wait "Booting in blind mode"`，`cnt_cycle` 每輪遞增，`while 1` 無止境，
 要停就關 Tera Term 的 macro）。**尚未上機驗證**。
 流程圖：`docs/Blanton_Test_Flow.drawio`。
-最後一次發布是 **V1.1.5**；SWB 的 I2C 通道與位址已於 2026-08-19 上機驗證。
+最後一次發布是 **V1.2.3**；SWB 的 I2C 通道與位址已於 2026-08-19 上機驗證。
 margin 的 `VNOM` 已於 2026-08-30 改為 Blanton 實測中位數（144 條軌中 86 條上調 0.8~2.5%）。
 交付用 `./publish/publish.sh` 打包。
 
@@ -123,6 +131,15 @@ bash ~/Blanton_Script/port_prbs_monitor.sh report       # PASS/FAIL 統計（沒
 bash ~/Blanton_Script/port_prbs_monitor.sh stop         # 收尾會跑 prbsstat STOp + prbs clear
 #   ⚠️ PRBS 打起來時 link 會顯示 down，這是正常的 —— 所以 start 刻意不印 port status
 
+# ── 溫度 / CPU 功耗（V1.2.3，已接進 PMON / Script 4）──
+~/Blanton_Script/ddr5_temp.sh                 # DDR5 DIMM 溫度（SPD5118，預設 bus 5, 0x50 0x51）
+~/Blanton_Script/ddr5_temp.sh 5 0x50          # 指定 bus / 位址
+~/Blanton_Script/hsc_temp_readback.sh         # LTC4287 HSC_MAIN(0x40)/HSC_STBY(0x45) 內外部溫度，bus 28，約 4 秒
+~/Blanton_Script/avt_pmpower.sh -p ~/AVT_Linux_NDA_2.8.37/AVTCMD      # CPU SktPwr / PPT / MemPwr
+~/Blanton_Script/avt_pmpower.sh -q -p ...     # 只印摘要，不倒整張 PM table
+#   ⚠️ AVT 是 NDA，不在交付包裡：DUT 上要先解壓到 ~/AVT_Linux_NDA_2.8.37/，沒有就每輪 exit 2
+#   ⚠️ 數值是 SMU telemetry 不是量測，要準就對照 VR 的 PMBus READ_POUT
+
 # ── PDB / CPB power brick 讀值 ──────────────────────
 ./Blanton_Script/pwr_brick.sh show         # Vin/Iin/Vout/Iout/Temp × 5 顆
 ./Blanton_Script/pwr_brick.sh show -r      # 多印 raw word
@@ -147,9 +164,38 @@ sleep 30                                      # 至少等一個 interval 再 rep
 ./Blanton_Script/blanton_ber.sh report        # 每 lane 一列，BER < 1e-6 才 PASS，最後 summary
 ./Blanton_Script/blanton_ber.sh stop          # prbsstat STOp
 ./Blanton_Script/blanton_ber.sh clear         # prbs clear（會解除 PRBS，要重測得再 init）
+#   summary 每個 unit 三列：200G ports / 100G p268 / TOTAL（兩個 unit 各有自己的 ce0(268)）
+#   ⚠️ 某一組「一條 lane 都沒回報」算 FAIL 不算 PASS —— 待測的 port 沉默不是通過
 #   -u 0 / -u 1 單邊；-c 1e-9 換門檻；-F 只列失敗；-f <log> 離線重解
 #   ⚠️ 不能跟 blanton_traffic_linespeed / blanton_tr518 同時跑（都會接管同一批 port）
 
+# ── SerDes DSC 擷取（TX_FIR / RXFFE / DFE / EYE / SNR）──
+./Blanton_Script/bcm_dsc_scan.sh                        # unit 0+1 全掃，約 10 分鐘
+./Blanton_Script/bcm_dsc_scan.sh -u 0                   # 只掃一個 unit（時間減半）
+./Blanton_Script/bcm_dsc_scan.sh -f my.log -F           # 自訂檔名 + 覆蓋
+./Blanton_Script/bcm_dsc_scan.sh -n                     # dry-run，只列要掃的 port
+#   log: ~/Blanton_Script/log/，掃完自動 cp 到 /host/hw-eval/jobs（-C 可關）
+#   檔名沒帶 %u 時會自動插 _u0 / _u1，所以兩個 unit 不會互相覆蓋
+#   結尾固定印 "### DSC_SCAN_DONE rc=<n>"；rc=0 才是全部 port 都拿到完整 dump
+#   ⚠️ 由 TTL 的 EN_TX_FIR 控制，預設 0（關）—— A 與 C 各掃一次，開了整輪多 ~20 分鐘
+
+# ── DSC raw log → CSV（離線解，Host 或 DUT 都可）──────
+sh ~/Blanton_Script/bcm_dsc_parse.sh -i blanton_dsc_ScriptA_u0.log -o u0
+#   產出 u0_lane.csv（每 lane 一列）+ u0_pm.csv（每 pm_id 一列）
+#   純 sh + awk（mawk 相容），欄位靠括號群組順序抓，SDK 改排版不會壞；
+#   群組數 != 9 的列標成 UNPARSED 印到 stderr，不會安靜解錯
+
+# ── 100G link down/up 循環 + DSC（TTL 尚未接）────────
+./Blanton_Script/bcm_100g_dsc_cycle.sh              # 印說明
+./Blanton_Script/bcm_100g_dsc_cycle.sh 200          # 跑 200 輪（-c 200 亦可）
+./Blanton_Script/bcm_100g_dsc_cycle.sh 200 -d       # 每行指令以灰色 [CMD] 印出來
+./Blanton_Script/bcm_100g_dsc_cycle.sh 20 -T        # 跳過 tuning
+./Blanton_Script/bcm_100g_dsc_cycle.sh 1 -n         # dry-run，不碰硬體也不 sleep
+#   log: ~/dsc_log/100G_dsc_cycle_test_<ts>.log，每輪一段 '### TEST CYCLE n/N'
+#   每輪收：兩個 unit 的 phydiag dsc + serdes-tx-get / serdes-rx-get sys 0..7
+#   等 link 是輪詢 'bcmcmd ps 268'（每 -p 秒，上限 -w 秒），不是 show interfaces status
+#   ⚠️ 尚未上機驗證；與 blanton_ber / blanton_traffic_linespeed / blanton_tr518 互斥
+
 # ── TR518 負載 + 量功耗（TTL 尚未接）─────────────────
 ./Blanton_Script/blanton_tr518.sh start       # 兩 unit，跑完 settle 120s
 ./Blanton_Script/TH6_SWB0_power_readback.sh   # 19 條軌 V×I + TOTAL POWER
@@ -304,9 +350,17 @@ Tera Term 連 COM port (115200-8-N-1)
   `Failed to execute the diagnostic command` 都照樣回 0），所以 `blanton_traffic_linespeed.sh`
   是**比對輸出**而非看 exit code。另外 `bcmcmd` 一律要 `</dev/null` ——
   否則它會吃掉 while 迴圈的 stdin，**只有第一個 VLAN 被設定**（V0.3.1 修過的 bug，很難看出來）。
+  **2026-09-07 `bcm_dsc_scan.sh` 又踩了同一個坑**：port 清單走 stdin，第一次 `bcmcmd` 就把剩下的吃光，
+  445 個 port 只掃了 1 個，而且 marker 與 dump 數量一起變少 → 比對通過、exit 0、log 看起來正常。
+  修法是迴圈改讀 fd 3（`done 3< "$PORTFILE"`）+ `bcmcmd ... < /dev/null`，並加一道
+  「實際迭代筆數 == 清單筆數」的檢查。**任何 `while ... done < file` 裡呼叫 `bcmcmd` 都要當它會讀 stdin。**
 - ⚠️ **`stress_hhmd.py` / `stress_pcie.py` 已於 2026-08-17 由 KC 移除**（Status 表 ScriptB #5/#7）。
   Script B 現在是 **8 個背景 job**（1 mlucas + 5 mem + ssd + usb），不是 10 個。
   I2C／PCIe 的持續讀取壓力目前沒有替代品。
+- ⚠️ **`pause` 是停 macro，`sleep` 是停 DUT**（V1.2.0 起 A/B/C 一律用後者）：`pause N` 期間 macro 不理會
+  DUT，shell 是閒著的，等於用猜的估上一個指令跑多久；`sendln "sleep N"` + `wait prompt_sonic_root`
+  把等待放到 DUT 上，prompt 回來才繼續，兩邊不會走散，而且這一段會帶時戳進 log。
+  **Script 4 / Script 5 尚未轉換，仍在用 `pause`**；B/C 開頭那個 `pause 1` 也保留（登入前沒有 prompt 可等）
 - ⚠️ **soak 迴圈沒有 `pause`**：取樣間隔不是 Status 表寫的 10 分鐘，而是取決於指令執行時間。
   （`-u 0` 已於 `491e807` 移除，A/B/C 現在都跑兩個 switch unit。）
 - 🔒 **`.sh` / `.conf` 一定要 LF**。CRLF 的 shell script 在 SONiC 上直接掛（`$'\r': command not found`）；
@@ -325,6 +379,15 @@ Tera Term 連 COM port (115200-8-N-1)
 - ⚠️ **兩張管理網卡同網段會 ARP flux**：`mgmt_ping_monitor.sh` 讓 eth0/eth1 同時 up，同一個 /24 下
   對端 ARP 可能由任一張卡回應，回包落在沒送封包的那張。`ARP_STRICT=1` 擋掉；判讀時看 `RESULT` 行的
   `nic_tx`/`nic_rx`（該卡自己的 packet delta）—— **ping 成功但 `nic_tx` 接近 0 = 封包從另一張卡出去的**
+- ⚠️ **`prbs get` 印的每一行是資料，不是 shell 的錯誤訊息**：沒鎖上的 lane 會印 `PRBS Error!`，
+  而 `blanton_ber.sh` 從 v1.0.0 就用 `grep -i 'ERROR|Invalid|...'` 掃**整份輸出**判斷「指令被拒絕」——
+  於是**跑得好好的 init 會報 `the BCM shell rejected 'phydiag ... prbs get'`**，而且因為提早 return，
+  那段「數 PRBS OK / 總數」的檢查根本沒跑，**你看到一個假錯誤，卻看不到哪幾條 lane 真的沒鎖**。
+  v1.1.1 已把 per-lane 行排除在錯誤掃描外、改成大小寫敏感，並把真正的拒絕訊息印出來
+- ⚠️ **BER 的 `clear` 才是把 lane 放回正常運作的動作**：V1.2.1 起 Script A 在第一輪流量**之前**跑 BER，
+  而 `blanton_ber.sh clear` 與緊接著的 `blanton_traffic_linespeed ps` 之間**沒有任何 settle**。
+  Script C 是流量報表之後才跑 BER，沒有這個順序問題。第一次上機時比對兩邊的 traffic report ——
+  **Script A 有 NA/FAIL 而 Script C 沒有，就是 lane 還沒回穩**，在 `clear` 後補一個 `sleep` 即可
 - ⚠️ **PRBS 跑起來時 `show interfaces status` 會顯示 DOWN**，那是 link 離開正常運作模式，不是故障。
   `port_prbs_monitor.sh` 的 `start` 因此刻意不印 port status（避免測試員誤判），只在 `prbs clear` 之後的報表裡印
 - ⚠️ **`ip -s link` 的欄位順序是 `bytes packets errors ...`**，要 packet 數取的是**第 2 欄**不是第 1 欄

docs/release-notes/v1.2.0.md

@@ -0,0 +1,76 @@
+# v1.2.0 — SerDes DSC capture, and the macro now waits on the DUT
+
+## ✨ New features
+
+**Full-machine SerDes DSC capture, before and after the soak**
+* `bcm_dsc_scan.sh` runs `phydiag <port> dsc` through the Broadcom diag shell across the whole port list — one 100G port plus the 200G ranges, about 445 per unit, on both units — and writes the raw log under `Blanton_Script/log/`, then copies it to `/host/hw-eval/jobs/`.
+* Script A takes a baseline and Script C takes a closing dump, so the pair brackets the stress run and the two are directly comparable.
+* `-u 0` scans one unit, `-f <name>` names the log (`%u` → `u0`/`u1`, `%t` → timestamp), `-F` overwrites, `-n` dry runs, `-C` skips the copy. A name without `%u` gets `_u0` / `_u1` inserted automatically, so unit 1 can never overwrite unit 0.
+* Every run ends with `### DSC_SCAN_DONE rc=<n>`. `rc=0` means every port returned a complete dump.
+* `phydiag ... dsc` is read-only — it does not change any SerDes setting.
+
+**`bcm_dsc_parse.sh` turns a raw DSC log into two CSVs**
+* `<prefix>_lane.csv` — one row per lane: TXEQ, RXFFE, DFE, EYE, SNR and the rest.
+* `<prefix>_pm.csv` — one row per `pm_id`: temperature, PLL, lane count, SNR/EYE statistics.
+* POSIX `sh` + `awk`, no Python, so it runs on the DUT as happily as on a laptop. Lane rows are read by the order of their bracket groups rather than by fixed column positions, so the SDK re-spacing its output does not break parsing; a row that does not yield 9 groups is reported as `UNPARSED` on stderr instead of being parsed wrongly.
+
+**`EN_TX_FIR` in `config.ttl` — the DSC scan is off by default**
+* A full scan is about 10 minutes and both Script A and Script C do one, so the shipped default (`0`) keeps ~20 minutes out of a routine run. Set it to `1` when the SerDes data is what you are after.
+
+**The macro now waits on the DUT instead of on itself**
+* Every `pause N` in Scripts A, B and C became `sendln "sleep N"` followed by `wait prompt_sonic_root`.
+* `pause` stopped the macro for N seconds without touching the DUT — the shell sat idle and the macro was guessing how long the previous command would take. On a loaded DUT the guess ran short and the next command went out before the previous one had finished, putting the whole run a beat ahead of the switch. Now the wait happens on the DUT and the macro resumes when the prompt actually comes back.
+* It also means the wait appears in the console log with a timestamp, so a round that ran long is visible afterwards.
+* Timings changed with it: the management-ping sample in Script A is 15 s (was 30), the settle after each traffic `clear` is 5 s (was 15). The traffic run itself stays 15 s and Script B's monitor loop stays 60 s.
+
+## 🐛 Bug fixes
+
+**The DSC scan only ever scanned one port — and reported success**
+* The scan loop read its port list on stdin, and `bcmcmd` reads stdin too, so the first call swallowed the rest of the file and the loop ended after a single port.
+* Nothing looked wrong. The log held one port marker and one dsc block, the marker-to-dump comparison passed because both numbers shrank together, the exit code was 0, and a 445-port scan simply finished in seconds.
+* The loop now reads on file descriptor 3 and `bcmcmd` is given `< /dev/null`, and there is a new check that the number of iterations matches the number of ports in the list — a check that cannot be fooled by the loop ending early.
+
+**Dead call sites removed from Scripts A, B and C**
+* The commented-out 100G PRBS calls, a duplicated commented 100G port-status block in Script A, and the stale `bmc_monitor_ddr.sh` block in Script C have been deleted. They had been dead since bring-up.
+* `port_prbs_monitor.sh` still ships and still runs by hand — but re-enabling it means writing the calls again, not un-commenting them.
+
+## 🔧 Changes
+
+* **Script C no longer prints the BMC poll log or the mlucas log to the console.** Both files are still copied to `/host/hw-eval/jobs/` and out to the USB stick with everything else; only the master log got shorter.
+
+## 📦 Downloads
+
+| File | Contents |
+|---|---|
+| `Script_ABC_Blanton_V1.2.0.zip` | The full Tera Term working directory, including `Blanton_Script/` to copy onto the DUT |
+
+**After copying to the DUT:**
+
+```bash
+chmod +x ~/Blanton_Script/*.sh      # bcm_dsc_scan.sh is invoked as ./Blanton_Script/... and needs it
+grep -rlU $'\r' ~/Blanton_Script    # expect no output
+ls ~/hammer/tools/amd/mlucas-avx2   # must already be there
+```
+
+## ⚠️ Before you run
+
+* **Replace `config.ttl` along with the macros.** `EN_TX_FIR` is new, and Tera Term aborts on an undefined variable rather than treating it as 0.
+* **`bcm_dsc_scan.sh` needs the execute bit.** Script A and Script C invoke it as `./Blanton_Script/bcm_dsc_scan.sh`. Without `chmod +x` it fails with `Permission denied`, the macro walks straight past it, and Script C's four `cp` lines then each report a missing file.
+* **The DSC scan shares the ports with `blanton_ber.sh`, `blanton_traffic_linespeed` and `blanton_tr518.sh`** — do not run it alongside any of them.
+* **Script 4 and Script 5 still use `pause`.** Only A, B and C were converted.
+* **`--runtime` is the job's overall limit, not a per-pass one.** `--passes` does not extend it; for a 24 hour soak set `RUNTIME` to `86400`.
+* **Script 4 has no teardown**: finish it with `blanton_tr518.sh stop` **and** `systemctl stop mlucas-amm`.
+* **Script 5 (reboot cycle) is still unverified on hardware**, has no exit condition, and its `wait "Booting in blind mode"` has no `timeout` guard.
+* **`blanton_multiphase_margin.sh save` is permanent**, and must not be mixed with `margin.sh`.
+* **`READ_VIN` and `READ_IIN` are still not in the ADPM12200 coefficient table.**
+* **The BMC USB service log only exists on the USB stick.**
+* **`FAN_SPEED` is 100.**
+* **Still unverified from v1.1.0**: the `ce0` ingress mirror, the 120 s settle in `blanton_tr518.sh`, and `test mode nr=no` on stop.
+
+## 🔗 Links
+
+* [ARCHITECTURE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/ARCHITECTURE.md) — test flow, data models, constraints
+* [CLAUDE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/CLAUDE.md) — commands and the bench gotchas
+* [Blanton_Test_Flow.drawio](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/docs/Blanton_Test_Flow.drawio) — the scripts side by side
+
+**Full changelog:** [V1.1.8...V1.2.0](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/compare/V1.1.8...V1.2.0)

docs/release-notes/v1.2.1.md

@@ -0,0 +1,49 @@
+# v1.2.1 — A BER baseline, so the SerDes numbers have something to be compared against
+
+## ✨ New features
+
+**Script A now takes a SerDes BER sweep before the first traffic run**
+* `blanton_ber.sh init → start → sleep 30 → report → stop → clear`, branched on `SWB_UNIT0` / `SWB_UNIT1` exactly like the traffic block beside it.
+* Script C already ran the closing sweep after its traffic report. With this one at the front, the pair brackets the soak — the same shape as the DSC scans added in v1.2.0, and the same reason: a BER figure on its own says very little, a *change* in it says a lot.
+* The `sleep 30` matches `blanton_ber.sh`'s `BER_INTERVAL`. Reporting before one full interval has accumulated reads a window that has not finished, and nothing warns you about it.
+
+## 🐛 Bug fixes
+
+**The new block's comment described the wrong position**
+* It was copied out of Script C, which runs BER *after* the traffic report, and the comment came with it and still said "after". In Script A the block runs *before* traffic. The comment now says what the code does and why the ordering is what it is.
+
+## ⚠️ Before you run
+
+* **Watch Script A's first traffic report on the first run.** PRBS holds the lanes out of normal operation and `blanton_ber.sh clear` is what releases them — and in Script A nothing settles between that `clear` and the `blanton_traffic_linespeed ps` / `init` that follows. Script C does not have this ordering, so the two reports are a built-in comparison: **if Script A shows NA or FAIL pairs that Script C does not, the lanes had not come back yet**, and a `sleep` after `clear` is the fix. This has not been run on hardware yet.
+* **`sleep 30` and `BER_INTERVAL` now live in three places** — Script A, Script C, and `blanton_ber.sh` itself. Changing one without the others silently reports a partial interval.
+* **BER, `blanton_traffic_linespeed` and `blanton_tr518.sh` cannot overlap.** They all take over the same ports. Script A now touches those ports twice before the soak even starts.
+* **`EN_TX_FIR` is still 0 by default**, so the DSC scans do not run unless you turn them on; a full scan is ~10 min in each of Script A and Script C.
+* **Replace `config.ttl` along with the macros.** Tera Term aborts the macro on an undefined variable rather than treating it as 0.
+* **`bcm_dsc_scan.sh` needs the execute bit**: `chmod +x ~/Blanton_Script/*.sh` after copying.
+* **`--runtime` is the job's overall limit, not a per-pass one.** `--passes` does not extend it.
+* **Script 4 has no teardown**: finish it with `blanton_tr518.sh stop` **and** `systemctl stop mlucas-amm`.
+* **Script 5 (reboot cycle) has no exit condition.** A 199-cycle / 60-hour run has now been analysed: PCIe AER stayed at 0, all 218 traffic pairs and all 864 lanes passed every cycle, and the BMC never reset. Two things it did surface — `bmc-first-enroll` does not exist on that BMC build, and NFC returned FAIL on every cycle.
+* **`blanton_multiphase_margin.sh save` is permanent**, and must not be mixed with `margin.sh`.
+* **`READ_VIN` and `READ_IIN` are still not in the ADPM12200 coefficient table.**
+* **The BMC USB service log only exists on the USB stick.**
+* **`FAN_SPEED` is 100.**
+* **Still unverified from v1.1.0**: the `ce0` ingress mirror, the 120 s settle in `blanton_tr518.sh`, and `test mode nr=no` on stop.
+
+## 📦 Downloads
+
+| File | Contents |
+|---|---|
+| `Script_ABC_Blanton_V1.2.1.zip` | The full Tera Term working directory, including `Blanton_Script/` to copy onto the DUT |
+
+```bash
+chmod +x ~/Blanton_Script/*.sh
+grep -rlU $'\r' ~/Blanton_Script    # expect no output
+ls ~/hammer/tools/amd/mlucas-avx2   # must already be there
+```
+
+## 🔗 Links
+
+* [ARCHITECTURE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/ARCHITECTURE.md) — test flow, data models, constraints
+* [CLAUDE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/CLAUDE.md) — commands and the bench gotchas
+
+**Full changelog:** [V1.2.0...V1.2.1](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/compare/V1.2.0...V1.2.1)

docs/release-notes/v1.2.2.md

@@ -0,0 +1,63 @@
+# v1.2.2 — The 100G uplink joins the BER sweep, and a boot cycle that can pull the power
+
+## ✨ New features
+
+**The BER sweep now measures port 268, the 100G uplink**
+* The port list ran `256-259` straight to `270-308`, so `ce0(268)` — the 100G uplink — was never in it. It is now its own group alongside the 200G ports.
+* The summary gives **each unit three rows**: `200G ports`, `100G p268`, and `TOTAL`. Unit 0 and unit 1 each have their own `ce0(268)`, and a marginal uplink lane averaged into 432 others is invisible; on its own row it is not.
+* A group that reports no lane at all now counts as a **failure**, not a pass. Silence on the port under test is the easiest way to ship a green report that measured nothing.
+
+**Script 5 is now a boot cycle, warm or cold**
+* `5_Blanton_Script_Reboot_Cycle.ttl` → `5_Blanton_Script_Boot_Cycle.ttl`, with `EN_Cold_Warm_boot` in `config.ttl` choosing: `1` = `reboot` (warm), `2` = a cold cycle by writing the CB FPGA, `0` = neither.
+* The log file and the per-round banner are named after the kind of boot: `Blanton_Reboot_Cycle_<ts>.log` / `Reboot Cycle : N`, or `Blanton_Power_Cycle_<ts>.log` / `Power Cycle : N`.
+* Both stress logs are removed before each run. `qfx5252-stress-*` appends to its `--log` and the macro `cat`s the whole thing, so every cycle was printing back everything the earlier cycles had written — 289 lines at cycle 1 and 36,555 by cycle 199. At roughly 6.2 ms a line on a 115200 console that accounted for **+212 s of the +214 s the cycle grew** over a 199-cycle run. The DUT was never getting slower.
+
+**`bcm_100g_dsc_cycle.sh` — 100G link down/up cycling with SerDes capture**
+* Tuning once, then N cycles of `port 268 en=0` → wait → `en=1` → wait → `phydiag 268 dsc` on both units → retimer `serdes-tx-get` / `serdes-rx-get` for `sys 0..7`. One log per run under `~/dsc_log/`, split by `### TEST CYCLE n/N`.
+* Waiting is a **poll of `bcmcmd ps 268`**, not `show interfaces status`. `port en=` changes the SDK, and the SONiC table only follows once gbsyncd has synced it — and this test pauses gbsyncd.
+* `-d` echoes every command as a grey `[CMD]` line before running it; `-n` is a dry run that touches nothing; the cycle count can be a bare argument (`./bcm_100g_dsc_cycle.sh 200`).
+
+## 🐛 Bug fixes
+
+**`blanton_ber.sh init` reported a hard error on runs that were working**
+* `[ERR ] unit 1: the BCM shell rejected 'phydiag ... prbs get'` — except the command was fine. `prbs get` prints one line per lane, a lane that has not locked says `PRBS Error!`, and the rejection check grepped the **whole** output case-insensitively for `ERROR|Invalid|...`.
+* Worse than the false alarm: the function returned early, so the lock count that was meant to judge those very lanes never ran. The operator saw an error they could not act on, and did **not** see which lanes had failed to lock. That check has been there since v1.0.0.
+* Per-lane result lines are now excluded, the match is case-sensitive, and a genuine rejection prints the offending line.
+
+## 🔧 Changes
+
+* **Script A takes a BER baseline before its first traffic run** (v1.2.1), so together with Script C's closing sweep the pair brackets the soak.
+* **`EN_TX_FIR`** gates the SerDes DSC scans in Script A and Script C. Default `0`: a full scan is ~10 min and both scripts do one.
+
+## 📦 Downloads
+
+| File | Contents |
+|---|---|
+| `Script_ABC_Blanton_V1.2.2.zip` | The full Tera Term working directory, including `Blanton_Script/` to copy onto the DUT |
+
+```bash
+chmod +x ~/Blanton_Script/*.sh
+grep -rlU $'\r' ~/Blanton_Script    # expect no output
+ls ~/hammer/tools/amd/mlucas-avx2   # must already be there
+```
+
+## ⚠️ Before you run
+
+* **Replace `config.ttl` with the macros.** `EN_Cold_Warm_boot` is new, and Tera Term aborts on an undefined variable rather than treating it as 0.
+* **Do not run the boot cycle with `EN_Cold_Warm_boot = 0`.** Nothing reboots, the `wait "Booting in blind mode"` underneath has no timeout, and since v1.2.2 there is no `logopen` either — so it hangs *and* leaves no log showing where. `0` is the value for the A → B → C flow, where that macro is not used.
+* **The cold path writes a raw FPGA register.** `0x480` is `ICB_CTRL_REG`; the register map carries no bit definitions for it and `0xD0000` is not documented anywhere in this repo. The BDF `0000:05:00.0` is hard-coded while `blanton_fpga_pcimem.sh` auto-detects it because it moves per unit — **check the BDF on every board before running the cold path**.
+* **Anything that parses these logs must accept both banners**, `Reboot Cycle : N` and `Power Cycle : N`. A parser that greps only the first finds zero cycles in a power-cycle log and reports nothing without complaining.
+* **`bcm_100g_dsc_cycle.sh` has not been run on hardware.** It pauses `gbsyncd0/1` for tuning and unpauses them on exit, Ctrl-C included; `-P` leaves them alone.
+* **`sleep 30` and `BER_INTERVAL` now live in three places** — Script A, Script C and `blanton_ber.sh`.
+* **BER, the DSC cycle, `blanton_traffic_linespeed` and `blanton_tr518.sh` cannot overlap.** They all take the same ports.
+* **Script 4 has no teardown**: finish it with `blanton_tr518.sh stop` **and** `systemctl stop mlucas-amm`.
+* **`blanton_multiphase_margin.sh save` is permanent**, and must not be mixed with `margin.sh`.
+* **`READ_VIN` and `READ_IIN` are still not in the ADPM12200 coefficient table.**
+* **`FAN_SPEED` is 100.**
+
+## 🔗 Links
+
+* [ARCHITECTURE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/ARCHITECTURE.md) — test flow, data models, constraints
+* [CLAUDE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/CLAUDE.md) — commands and the bench gotchas
+
+**Full changelog:** [V1.2.1...V1.2.2](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/compare/V1.2.1...V1.2.2)

docs/release-notes/v1.2.3.md

@@ -0,0 +1,53 @@
+# v1.2.3 — DIMM and hot-swap temperatures in every snapshot, and CPU power next to the switch rails
+
+## ✨ New features
+
+**Every PMON snapshot now reads DDR5 DIMM and hot-swap controller temperatures**
+* `utils/setup_pmon.ttl` runs `ddr5_temp.sh` and `hsc_temp_readback.sh` right after `show platform temperature`. Because `setup_pmon` is shared, this lands everywhere a snapshot is taken: Script A's baseline, each Script B soak round, Script C, the Script 4 loop and every Script 5 check point.
+* `ddr5_temp.sh` reads the SPD5118 hub on each DIMM: i2c bus 5, `0x50` / `0x51`, register `0x31` (`bit[12:2]`, sign bit 12, 0.25 °C/LSB). A read that fails prints `read fail` — never a number it did not read. Bus and addresses can be passed: `ddr5_temp.sh [bus] [addr ...]`.
+* `hsc_temp_readback.sh` reads both LTC4287 hot-swap controllers on i2c bus 28 — `HSC_MAIN @ 0x40` (PU11 internal / PQ1 external) and `HSC_STBY @ 0x45` (PU46 internal / PQ53 external). The source is selected through `0xF3`, then `READ_TEMPERATURE` `0x8D` is read in Kelvin and converted.
+
+**Script 4 logs AMD CPU package power every round**
+* `avt_pmpower.sh` runs `AVTCMD -module pmm "get_pmdata()"` and summarizes `SktPwr`, `PPT Fast` / `PPT Slow` against their limits, and `MemPwr`.
+* It runs after the two `TH6_SWB` power readbacks, so each sample now puts the switch rails and the CPU package side by side.
+* `-q` prints the summary only. Exit `2` = AVTCMD not found, `3` = AVTCMD failed, `4` = the PM table parsed to nothing (format changed).
+
+## 🐛 Bug fixes
+
+**`hsc_temp_readback.sh` was saved with CRLF line endings**
+* Copied to the DUT as-is, bash on SONiC fails on the first line (`$'\r': command not found`). The shipped file is LF.
+* Its comments said the delay between I2C transactions was 100 ms; `DELAY=0.5` is what actually runs. Comments corrected and a Version History header added.
+
+## 📦 Downloads
+
+| File | Contents |
+|---|---|
+| `Script_ABC_Blanton_V1.2.3.zip` | The full Tera Term working directory, including `Blanton_Script/` to copy onto the DUT |
+
+```bash
+chmod +x ~/Blanton_Script/*.sh
+grep -rlU $'\r' ~/Blanton_Script              # expect no output
+ls ~/AVT_Linux_NDA_2.8.37/AVTCMD              # Script 4 only - must already be there
+```
+
+## ⚠️ Before you run
+
+* **Redeploy `Blanton_Script/`.** If an earlier copy of `hsc_temp_readback.sh` reached the DUT, it is CRLF and will not run.
+* **`chmod +x` after deploying.** `setup_pmon` calls both new scripts by path. Without the exec bit each call is `Permission denied` and the snapshot carries on without those rows — nothing stops, nothing warns.
+* **Each PMON snapshot is ~4 s longer.** `hsc_temp_readback.sh` sleeps 0.5 s twice for each of its four readings. It adds up in Script 5, which snapshots at every check point.
+* **AVT is not in this package (NDA).** Unpack it on the DUT at exactly `~/AVT_Linux_NDA_2.8.37/` before Script 4. Missing, the call exits `2` every round and the loop runs on without a CPU power reading.
+* **Script 4 logs the full PM table once a minute**, because the call is made without `-q`.
+* **CPU power is SMU telemetry, not a measurement.** Its absolute accuracy is whatever the BIOS SVI calibration gives — cross-check against the VR's PMBus `READ_POUT` when the number matters.
+* **None of the three new scripts has been checked against the Script A/B/C flow on hardware yet.**
+* **Do not run the boot cycle with `EN_Cold_Warm_boot = 0`**, and check the hard-coded BDF on every board before the cold path (see v1.2.2).
+* **BER, the DSC cycle, `blanton_traffic_linespeed` and `blanton_tr518.sh` cannot overlap.** They all take the same ports.
+* **Script 4 has no teardown**: finish it with `blanton_tr518.sh stop` **and** `systemctl stop mlucas-amm`.
+* **`blanton_multiphase_margin.sh save` is permanent**, and must not be mixed with `margin.sh`.
+* **`FAN_SPEED` is 100.**
+
+## 🔗 Links
+
+* [ARCHITECTURE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/ARCHITECTURE.md) — test flow, data models, constraints
+* [CLAUDE.md](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/src/branch/main/CLAUDE.md) — commands and the bench gotchas
+
+**Full changelog:** [V1.2.2...V1.2.3](https://etgit.et-wen.com/etwen/Blanton_TTL_Script/compare/V1.2.2...V1.2.3)

src/Script_ABC_Blanton/1_Blanton_Script_A.ttl

@@ -1,7 +1,7 @@
 ; =============================================================================
 ; Script A for Blanton
-; Version : V1.1.9
-; Date    : 2026-09-07
+; Version : V1.2.3
+; Date    : 2026-09-23
 ; Author  : ETWen
 ; =============================================================================
 ; Version History:
@@ -484,6 +484,262 @@
 ;                                                                            bmc_monitor.sh and friends in the chmod +x line after
 ;                                                                            deployment. Without it both scans fail with Permission
 ;                                                                            denied and the macro walks straight past it
+;   V1.2.0  2026-09-07
+;                       Blanton_Script/bcm_dsc_scan.sh                  v1.3.0 bcmcmd was eating the port list
+;                                                                         The scan loop read the port file on stdin, and bcmcmd
+;                                                                         reads stdin too, so the first call swallowed the rest of
+;                                                                         the file and the loop ended after ONE port
+;                                                                         Nothing looked wrong: the log held one PORT marker and
+;                                                                         one dsc block, markers == dumps, exit code 0. A 445 port
+;                                                                         scan finished in seconds and reported success
+;                                                                         Fixed by reading the loop on fd 3 (done 3< "$PORTFILE")
+;                                                                         and giving bcmcmd < /dev/null
+;                                                                         Added a check that the iteration count equals the port
+;                                                                         list count. The marker / dump comparison cannot catch a
+;                                                                         loop that ends early, because both numbers shrink
+;                                                                         together; the Saved: line now reports dumps out of TOTAL,
+;                                                                         not out of markers
+;                                                                         !! this is the same bcmcmd trap
+;                                                                            blanton_traffic_linespeed.sh hit at v0.3.1, where only
+;                                                                            the first VLAN was configured. Every while ... done <
+;                                                                            file loop that calls bcmcmd needs < /dev/null - assume
+;                                                                            it will read stdin unless proven otherwise
+;                       ScriptA / ScriptB / ScriptC                     Wait on the DUT with 'sleep', not on the macro with 'pause'
+;                                                                         pause N stops the macro for N seconds without touching
+;                                                                         the DUT: the shell sits idle and the macro is guessing
+;                                                                         how long the last command took. sendln "sleep N" + wait
+;                                                                         prompt_sonic_root moves the wait onto the DUT, so the
+;                                                                         macro resumes when the prompt actually comes back and the
+;                                                                         two cannot drift apart
+;                                                                         It also lands in the console log with a timestamp, so a
+;                                                                         round that ran long is visible afterwards instead of
+;                                                                         invisible
+;                                                                         Durations changed with it: ScriptA mgmt ping 30 -> 15 s;
+;                                                                         the settle after every traffic 'clear' 15 -> 5 s; the
+;                                                                         traffic run itself stays 15 s; ScriptB's monitor loop
+;                                                                         stays 60 s
+;                                                                         !! Script4 and Script5 were NOT converted and still use
+;                                                                            pause. The 'pause 1' at the top of ScriptB / ScriptC
+;                                                                            also stays - it only spaces the log header and runs
+;                                                                            before there is a prompt to wait for
+;                       config.ttl                                      Add EN_TX_FIR to gate the SerDes DSC scan
+;                                                                         EN_TX_FIR = 1 enables bcm_dsc_scan.sh in ScriptA and
+;                                                                         ScriptC, and the four cp lines that carry
+;                                                                         blanton_dsc_Script{A,C}_u{0,1}.log to /host/hw-eval/jobs.
+;                                                                         Default is 0
+;                                                                         A full scan is ~10 min and both scripts do one, so
+;                                                                         leaving it off keeps ~20 min out of a routine run. Turn
+;                                                                         it on when the SerDes data is what you are after
+;                       ScriptC                                         Stop printing the BMC poll and mlucas logs to the console
+;                                                                         cat bmc_poll.log and cat mlucas_amm_log are commented
+;                                                                         out. Both files are still copied to /host/hw-eval/jobs
+;                                                                         and out to the USB stick with everything else, so no data
+;                                                                         is lost - the master log is just shorter
+;   V1.2.1  2026-09-08
+;                       ScriptA                                         Add a BER baseline sweep before the traffic run
+;                                                                         blanton_ber.sh init / start / sleep 30 / report / stop /
+;                                                                         clear, branched on SWB_UNIT0 and SWB_UNIT1 the same way
+;                                                                         the traffic block is. ScriptC already took the closing
+;                                                                         sweep after its traffic report, so the two now bracket
+;                                                                         the soak the way the DSC scans do
+;                                                                         sleep 30 is not arbitrary: it is blanton_ber.sh's
+;                                                                         BER_INTERVAL. 'report' before one full interval has
+;                                                                         accumulated reads a window that has not finished
+;                                                                         The block was copied from ScriptC, which runs it AFTER
+;                                                                         traffic, and its comment said so. In ScriptA it runs
+;                                                                         BEFORE traffic, so the comment was rewritten to match
+;                                                                         where the code actually is
+;                                                                         !! nothing settles between 'blanton_ber.sh clear' and
+;                                                                            'blanton_traffic_linespeed ps' that follows it. PRBS
+;                                                                            holds the lanes out of normal operation and 'clear' is
+;                                                                            what releases them, so the first traffic run of
+;                                                                            ScriptA now starts on lanes that have just been
+;                                                                            released. ScriptC does not have this ordering. Watch
+;                                                                            ScriptA's first traffic report for NA or FAIL pairs
+;                                                                            that ScriptC's does not show - if they appear, a sleep
+;                                                                            after 'clear' is the fix
+;                                                                         !! ScriptA now runs BER twice as far as the switch is
+;                                                                            concerned: once here and once inside ScriptC. Neither
+;                                                                            can overlap blanton_traffic_linespeed or
+;                                                                            blanton_tr518.sh - they all take over the same ports
+;   V1.2.2  2026-09-15
+;                       5_.._Boot_Cycle.ttl                             Renamed from 5_Blanton_Script_Reboot_Cycle.ttl
+;                                                                         It does warm and cold now, so 'Reboot' was too narrow.
+;                                                                         Same macro otherwise - git records it as a rename
+;                       5_.._Boot_Cycle.ttl                             Warm or cold boot, chosen by EN_Cold_Warm_boot
+;                                                                         1 = 'reboot' (warm, what the macro always did). 2 = cold,
+;                                                                         by writing the CB FPGA: pcimem
+;                                                                         /sys/bus/pci/devices/0000:05:00.0/resource0 0x480 w
+;                                                                         0xD0000. 0 = neither
+;                                                                         !! EN_Cold_Warm_boot = 0 hangs the macro. Neither branch
+;                                                                            runs, so nothing reboots, and the 'wait "Booting in
+;                                                                            blind mode"' underneath has no timeout - cycle 1
+;                                                                            finishes and the macro then waits for a boot that will
+;                                                                            never come. 0 is the value for the A/B/C flow, where
+;                                                                            this macro is not used at all; do not run ScriptBoot
+;                                                                            with it
+;                                                                         !! 0x480 is ICB_CTRL_REG in
+;                                                                            docs/Blantons_FPGA_Registers.md, and that table
+;                                                                            carries no bit definitions for it. 0xD0000 is not
+;                                                                            written down anywhere in this repo either. Whoever
+;                                                                            knows what those bits do should put it in the register
+;                                                                            doc before someone changes the value
+;                                                                         !! the BDF 0000:05:00.0 is hard-coded here, while
+;                                                                            blanton_fpga_pcimem.sh auto-detects the CB FPGA
+;                                                                            precisely because it moves per unit (see the V1.0.x
+;                                                                            notes and Key Constraints #4). On a DUT where the FPGA
+;                                                                            is not at 05:00.0 this becomes a raw 32-bit write to
+;                                                                            an unknown register on some other device. Verify the
+;                                                                            BDF on every unit before running the cold path
+;                                                                         !! NOT verified on hardware. The warm path has 199 cycles
+;                                                                            behind it; the cold path has none
+;                       5_.._Boot_Cycle.ttl                             Truncate the two stress logs before each run
+;                                                                         rm -rf /host/hw-eval/jobs/qfx5252-stress-ssd.log and the
+;                                                                         usb one, added ahead of each qfx5252-stress-* call
+;                                                                         qfx5252-stress-* APPENDS to its --log file and the macro
+;                                                                         cats the whole thing afterwards, so every cycle printed
+;                                                                         back everything the ones before it had written
+;                                                                         Measured on the 199 cycle log from 2026-09-04: cycle 1
+;                                                                         printed 289 lines, cycle 199 printed 36,555. At ~6.2 ms a
+;                                                                         line - which is what a 115200 baud console costs - that
+;                                                                         is +212 s of the +214 s the cycle grew over the run. The
+;                                                                         stress itself is fixed at --runtime 30, and the other
+;                                                                         eleven segments between check points drifted by less than
+;                                                                         1.5 s each. The DUT was never getting slower; the test
+;                                                                         was reading its own history aloud once per cycle
+;                       5_.._Boot_Cycle.ttl                             Name the log file and the banner after the kind of boot
+;                                                                         EN_Cold_Warm_boot = 1 gives
+;                                                                         Logs\Blanton_Reboot_Cycle_<ts>.log and a 'Reboot Cycle :
+;                                                                         N' banner; = 2 gives Blanton_Power_Cycle_<ts>.log and
+;                                                                         'Power Cycle : N'. Three sites now branch on the flag:
+;                                                                         the log name, the banner and the boot itself
+;                                                                         !! with 0 there is no longer a logopen either, so the run
+;                                                                            that already hangs at wait "Booting in blind mode" now
+;                                                                            also leaves no log to show where it stopped. EN_log =
+;                                                                            1 no longer guarantees a log in this macro -
+;                                                                            EN_Cold_Warm_boot has to be 1 or 2 as well
+;                                                                         !! anything that parses these logs has to accept BOTH
+;                                                                            banners. The cycle banner is the record separator the
+;                                                                            check-point and per-segment timing reports are built
+;                                                                            on, so a parser that only greps 'Reboot Cycle :' finds
+;                                                                            zero cycles in a power-cycle log and silently reports
+;                                                                            nothing at all
+;                                                                         The logopen timestamp flag is still a literal 1 here
+;                                                                         rather than EN_timestamp the way ScriptA does it. Leaving
+;                                                                         it on is the right call - the per-segment timing analysis
+;                                                                         is derived from those timestamps and there is nothing
+;                                                                         else to recover them from - but it does mean this macro
+;                                                                         ignores EN_timestamp = 0
+;                       config.ttl                                      Add EN_Cold_Warm_boot
+;                                                                         0 = normal test (A/B/C), 1 = reboot cycle, 2 = power
+;                                                                         cycle. Default 0 so that opening the shared config cannot
+;                                                                         reboot anyone's DUT by accident
+;                       Blanton_Script/blanton_ber.sh                   v1.1.0 Add port 268, the 100G uplink
+;                                                                         The port list jumps 256-259 -> 270-308, so 268 (ce0) was
+;                                                                         never measured. It is now its own group: BER_PORTS_200G
+;                                                                         and BER_PORTS_100G, joined for the phydiag command but
+;                                                                         reported apart
+;                                                                         The summary gives each unit three rows - 200G ports /
+;                                                                         100G p268 / TOTAL - because unit 0 and unit 1 each have
+;                                                                         their own ce0(268). A bad uplink lane averaged into 432
+;                                                                         others is invisible; on its own row it is not
+;                                                                         TOTAL is not a hand-added sum: every lane is folded into
+;                                                                         its own group and into ALL separately, so the parts
+;                                                                         cannot drift from the whole
+;                                                                         !! a group that reports no lane at all is a FAILURE, not
+;                                                                            a pass. Silence on the port under test is the easiest
+;                                                                            way to ship a green report that measured nothing
+;                       Blanton_Script/blanton_ber.sh                   v1.1.1 Stop reading lane results as shell errors
+;                                                                         init kept answering "the BCM shell rejected 'phydiag ...
+;                                                                         prbs get'" on runs that were working. The check grepped
+;                                                                         the WHOLE output case-insensitively for
+;                                                                         ERROR|Invalid|..., and 'prbs get' prints one line per
+;                                                                         lane - a lane that had not locked says PRBS Error!, which
+;                                                                         matched
+;                                                                         So a good run reported a hard error, and worse, the
+;                                                                         function returned before the lock-count check that was
+;                                                                         supposed to judge those very lanes. The operator saw a
+;                                                                         failure and did NOT see which lanes were unlocked
+;                                                                         Per-lane lines are now excluded from the check, the match
+;                                                                         is case-sensitive, and a genuine rejection prints the
+;                                                                         offending line so it can be read
+;                                                                         !! this was in the file from v1.0.0. Any earlier init
+;                                                                            that printed that error was probably fine, and any
+;                                                                            earlier init that passed said nothing about lanes that
+;                                                                            had failed to lock
+;                       Blanton_Script/bcm_100g_dsc_cycle.sh            Created v1.2.0 - 100G link down/up cycle with DSC capture
+;                                                                         Tuning once (gbsyncd pause, serdes-tx-set sys 0..7,
+;                                                                         tx_taps per lane), then N cycles of: port en=0, wait,
+;                                                                         port en=1, wait, phydiag dsc on both units, serdes-tx-get
+;                                                                         and serdes-rx-get sys 0..7. One log per run under
+;                                                                         ~/dsc_log, split by '### TEST CYCLE n/N'
+;                                                                         Waiting polls 'bcmcmd ps <port>' every -p seconds up to
+;                                                                         -w, and reads the state from the row whose first field
+;                                                                         ends in (<port>). Asking the SDK matters here: 'port en='
+;                                                                         changes the SDK, while 'show interfaces status' only
+;                                                                         follows once gbsyncd has synced it - and this test pauses
+;                                                                         gbsyncd
+;                                                                         -d prints every command as [CMD] in grey before running
+;                                                                         it, CMD_DELAY paces them, -n is a dry run that touches
+;                                                                         nothing and sleeps not at all
+;                                                                         !! all output is ASCII English on purpose. The DUT serial
+;                                                                            console mangles UTF-8: a Chinese error message came
+;                                                                            back as "ERROR: -c ? 1", which is worse than no
+;                                                                            message
+;                                                                         !! NOT verified on hardware
+;                       tools/100G_dsc_cycle.txt                        Created - the hand-typed command list behind that script
+;                                                                         Same role as BER_Test.txt and TR518.txt: the bench
+;                                                                         version of the commands, kept so the .sh can be checked
+;                                                                         against what a person would actually type. Change one and
+;                                                                         change the other
+;   V1.2.3  2026-09-23  utils/setup_pmon.ttl                            Add DDR5 DIMM temperature + hot-swap controller temperature
+;                                                                         ~/Blanton_Script/ddr5_temp.sh, then hsc_temp_readback.sh,
+;                                                                         right after 'show platform temperature'
+;                                                                         setup_pmon is shared, so this lands in every PMON snapshot:
+;                                                                         ScriptA baseline, every ScriptB soak round, ScriptC, the
+;                                                                         Script 4 loop and each Script 5 check point
+;                                                                         !! hsc_temp_readback.sh sleeps 0.5 s twice per reading and
+;                                                                            takes four readings - ~4 s added to every PMON snapshot
+;                                                                         !! both are called by path, not through bash, so they need
+;                                                                            the exec bit on the DUT: chmod +x ~/Blanton_Script/*.sh
+;                                                                            after deploying. Without it each call is Permission
+;                                                                            denied and the snapshot just goes on without the rows
+;                       Blanton_Script/ddr5_temp.sh                     Created v1.0.1 - DDR5 DIMM temperature from the SPD5118 hub
+;                                                                         i2cget bus 5, DIMM 0x50 / 0x51, register 0x31 (MR49/MR50)
+;                                                                         bit[12:2], sign bit 12, 0.25 C/LSB. Bus and addresses can
+;                                                                         be given as arguments: ddr5_temp.sh [bus] [addr ...]
+;                                                                         A failed read prints 'read fail' and moves on to the next
+;                                                                         DIMM - it never prints a number it did not read
+;                       Blanton_Script/hsc_temp_readback.sh             Created - LTC4287 hot-swap controller temperatures
+;                                                                         Native i2c bus 28. HSC_MAIN @ 0x40 (PU11 internal / PQ1
+;                                                                         external) and HSC_STBY @ 0x45 (PU46 internal / PQ53
+;                                                                         external). Source picked by writing 0xF3 (0xEB internal,
+;                                                                         0xEF external), then READ_TEMPERATURE 0x8D, Kelvin -> C
+;                                                                         v1.0.1 Add the header + Version History, fix the delay
+;                                                                         comments (they said 100 ms; DELAY is 0.5 s)
+;                                                                         !! v1.0.0 was saved with CRLF line endings. On SONiC that
+;                                                                            fails outright ($'\r': command not found) - now LF
+;                       Blanton_Script/avt_pmpower.sh                   Created v1.0.0 - AMD CPU package power from the AVT PM table
+;                                                                         AVTCMD -module pmm "get_pmdata()", then a summary of
+;                                                                         SktPwr, PPT Fast / Slow against their limits, and MemPwr
+;                                                                         -p <AVTCMD path>, -q for the summary without the raw table
+;                                                                         Exit 2 = AVTCMD not found, 3 = AVTCMD failed, 4 = the table
+;                                                                         parsed to nothing (format changed)
+;                                                                         !! SMU telemetry, not a measurement - its absolute accuracy
+;                                                                            is whatever the BIOS SVI calibration gives. Cross-check
+;                                                                            against the VR's PMBus READ_POUT when the number matters
+;                       4_Blanton_Script_thermal_safety.ttl             Add CPU package power to every loop round
+;                                                                         avt_pmpower.sh -p ~/AVT_Linux_NDA_2.8.37/AVTCMD, after the
+;                                                                         two TH6_SWB power readbacks - so each round now has the
+;                                                                         switch rails and the CPU package side by side
+;                                                                         !! AVT is NOT in Blanton_Script and does not travel with
+;                                                                            this package (NDA). It has to be unpacked on the DUT at
+;                                                                            exactly ~/AVT_Linux_NDA_2.8.37/ beforehand. If it is not
+;                                                                            there the script exits 2 every round and the loop carries
+;                                                                            on without a CPU power reading
+;                                                                         !! without -q the full PM table is printed every round, and
+;                                                                            Script 4 loops once a minute - the log grows by one full
+;                                                                            table per minute
 ; =============================================================================
 include "config.ttl"
 
@@ -649,7 +905,8 @@ include "utils/show_dmesg.ttl"
 wait prompt_sonic_root
 sendln "./Blanton_Script/mgmt_ping_monitor.sh start"
 wait prompt_sonic_root
-pause 30
+sendln "sleep 15"
+wait prompt_sonic_root
 sendln "~/Blanton_Script/mgmt_ping_monitor.sh stop"
 wait prompt_sonic_root
 sendln "cat ~/Blanton_Script/log/mgmt_ping.log"
@@ -692,6 +949,56 @@ sendln "config feature state lldp disabled"
 wait prompt_sonic_root
 sendln "config save -y"
 
+; ========== BER ==========
+; Baseline sweep, taken BEFORE the traffic run - ScriptC takes the closing
+; one after its traffic report, so the pair brackets the soak.
+; PRBS takes the SerDes out of normal operation; 'clear' is what puts the
+; lanes back, so it has to run before the traffic block below.
+; sleep 30 matches blanton_ber.sh BER_INTERVAL - reporting earlier reads an
+; interval that has not finished accumulating.
+if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh init"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh start"
+    wait prompt_sonic_root
+    sendln "sleep 30"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh report"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh stop"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh clear"
+elseif SWB_UNIT0 = 1 && SWB_UNIT1 = 0 then
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh init -u 0"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh start -u 0"
+    wait prompt_sonic_root
+    sendln "sleep 30"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh report -u 0"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh stop -u 0"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh clear -u 0"
+elseif SWB_UNIT0 = 0 && SWB_UNIT1 = 1 then
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh init -u 1"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh start -u 1"
+    wait prompt_sonic_root
+    sendln "sleep 30"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh report -u 1"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh stop -u 1"
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/blanton_ber.sh clear -u 1"
+else
+
+endif
+
 if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed ps"
@@ -700,12 +1007,14 @@ if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed clear"
     wait prompt_sonic_root
-    pause 15
+    sendln "sleep 5"
+    wait prompt_sonic_root
     sendln "blanton_traffic_linespeed show"
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed start"
     wait prompt_sonic_root
-    pause 15
+    sendln "sleep 15"
+    wait prompt_sonic_root
     sendln "blanton_traffic_linespeed stop"
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed report"
@@ -717,12 +1026,14 @@ elseif SWB_UNIT0 = 1 && SWB_UNIT1 = 0 then
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed clear -u 0"
     wait prompt_sonic_root
-    pause 15
+    sendln "sleep 5"
+    wait prompt_sonic_root
     sendln "blanton_traffic_linespeed show -u 0"
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed start -u 0"
     wait prompt_sonic_root
-    pause 15
+    sendln "sleep 15"
+    wait prompt_sonic_root
     sendln "blanton_traffic_linespeed stop -u 0"
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed report -u 0"
@@ -734,12 +1045,14 @@ elseif SWB_UNIT0 = 0 && SWB_UNIT1 = 1 then
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed clear -u 1"
     wait prompt_sonic_root
-    pause 15
+    sendln "sleep 5"
+    wait prompt_sonic_root
     sendln "blanton_traffic_linespeed show -u 1"
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed start -u 1"
     wait prompt_sonic_root
-    pause 15
+    sendln "sleep 15"
+    wait prompt_sonic_root
     sendln "blanton_traffic_linespeed stop -u 1"
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed report -u 1"
@@ -747,9 +1060,11 @@ else
 
 endif
 
-; ========== Collect bcm dsc data ==========
-wait prompt_sonic_root
-sendln "./Blanton_Script/bcm_dsc_scan.sh -f blanton_dsc_ScriptA.log -F"
+if EN_TX_FIR = 1 then
+    ; ========== Collect bcm dsc data ==========
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/bcm_dsc_scan.sh -f blanton_dsc_ScriptA.log -F"
+endif
 
 ; ========== Show Power on uptime ==========
 wait prompt_sonic_root

src/Script_ABC_Blanton/2_Blanton_Script_B.ttl

@@ -109,7 +109,8 @@ timeout = 0
 wait prompt_sonic_root
 sendln "./Blanton_Script/mgmt_ping_monitor.sh start"
 wait prompt_sonic_root
-pause 3
+sendln "sleep 3"
+wait prompt_sonic_root
 sendln "./Blanton_Script/mgmt_ping_monitor.sh status"
 
 ; ========== NFC Test ==========
@@ -139,7 +140,8 @@ if SWB_UNIT0 = 1 && SWB_UNIT1 = 1 then
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed clear"
     wait prompt_sonic_root
-    pause 15
+    sendln "sleep 5"
+    wait prompt_sonic_root
     sendln "blanton_traffic_linespeed show"
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed start"
@@ -151,7 +153,8 @@ elseif SWB_UNIT0 = 1 && SWB_UNIT1 = 0 then
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed clear -u 0"
     wait prompt_sonic_root
-    pause 15
+    sendln "sleep 5"
+    wait prompt_sonic_root
     sendln "blanton_traffic_linespeed show -u 0"
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed start -u 0"
@@ -163,7 +166,8 @@ elseif SWB_UNIT0 = 0 && SWB_UNIT1 = 1 then
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed clear -u 1"
     wait prompt_sonic_root
-    pause 15
+    sendln "sleep 5"
+    wait prompt_sonic_root
     sendln "blanton_traffic_linespeed show -u 1"
     wait prompt_sonic_root
     sendln "blanton_traffic_linespeed start -u 1"
@@ -173,7 +177,7 @@ endif
 
 
 
-; ========== Monitor loop: platform data + background jobs (pause 60s per round) ==========
+; ========== Monitor loop: platform data + background jobs (sleep 60s per round) ==========
 while 1
     include "utils/setup_pmon.ttl"
     wait prompt_sonic_root
@@ -182,5 +186,6 @@ while 1
     sendln "jobs"
     wait prompt_sonic_root
     sendln "systemctl is-active mlucas-amm"
-    pause 60
+    wait prompt_sonic_root
+    sendln "sleep 60"
 endwhile

src/Script_ABC_Blanton/3_Blanton_Script_C.ttl

@@ -53,8 +53,8 @@ sendln "/usr/sbin/ras-mc-ctl --summary"
 ; ========== BMC Monitor TAKE DATA ==========
 wait prompt_sonic_root
 sendln "./Blanton_Script/bmc_monitor.sh stop"
-wait prompt_sonic_root
-sendln "cat ./Blanton_Script/log/bmc_poll.log"
+; wait prompt_sonic_root
+; sendln "cat ./Blanton_Script/log/bmc_poll.log"
 
 ; ========== BMC USB Test result ==========
 wait prompt_sonic_root
@@ -64,8 +64,8 @@ sendln "journalctl -u qfx5252-bmc-usb-net-test.service --no-pager -o short-iso >
 
 
 ; ========== CHECK Stress results ==========
-wait prompt_sonic_root
-sendln "cat ~/hammer/tools/amd/mlucas_amm_log"
+; wait prompt_sonic_root
+; sendln "cat ~/hammer/tools/amd/mlucas_amm_log"
 wait prompt_sonic_root
 sendln "cat /host/hw-eval/jobs/qfx5252-stress-ssd.log"
 wait prompt_sonic_root
@@ -150,10 +150,11 @@ else
 
 endif
 
-; ========== Collect bcm dsc data ==========
-wait prompt_sonic_root
-sendln "./Blanton_Script/bcm_dsc_scan.sh -f blanton_dsc_ScriptC.log -F"
-
+if EN_TX_FIR = 1 then
+    ; ========== Collect bcm dsc data ==========
+    wait prompt_sonic_root
+    sendln "./Blanton_Script/bcm_dsc_scan.sh -f blanton_dsc_ScriptC.log -F"
+endif
 
 ; ========== NVME Err Info ==========
 wait prompt_sonic_root
@@ -199,14 +200,17 @@ wait prompt_sonic_root
 sendln "cp ./Blanton_Script/log/mgmt_ping.log /host/hw-eval/jobs/"
 wait prompt_sonic_root
 sendln "cp ./Blanton_Script/log/nfc_poll.log /host/hw-eval/jobs/"
-wait prompt_sonic_root
-sendln "cp ./Blanton_Script/log/blanton_dsc_ScriptA_u0.log /host/hw-eval/jobs/"
-wait prompt_sonic_root
-sendln "cp ./Blanton_Script/log/blanton_dsc_ScriptA_u1.log /host/hw-eval/jobs/"
-wait prompt_sonic_root
-sendln "cp ./Blanton_Script/log/blanton_dsc_ScriptC_u0.log /host/hw-eval/jobs/"
-wait prompt_sonic_root
-sendln "cp ./Blanton_Script/log/blanton_dsc_ScriptC_u1.log /host/hw-eval/jobs/"
+
+if EN_TX_FIR = 1 then
+    wait prompt_sonic_root
+    sendln "cp ./Blanton_Script/log/blanton_dsc_ScriptA_u0.log /host/hw-eval/jobs/"
+    wait prompt_sonic_root
+    sendln "cp ./Blanton_Script/log/blanton_dsc_ScriptA_u1.log /host/hw-eval/jobs/"
+    wait prompt_sonic_root
+    sendln "cp ./Blanton_Script/log/blanton_dsc_ScriptC_u0.log /host/hw-eval/jobs/"
+    wait prompt_sonic_root
+    sendln "cp ./Blanton_Script/log/blanton_dsc_ScriptC_u1.log /host/hw-eval/jobs/"
+endif
 
 wait prompt_sonic_root
 getdate ts_date "%Y%m%d"

src/Script_ABC_Blanton/4_Blanton_Script_thermal_safety.ttl

@@ -152,6 +152,8 @@ while 1
     sendln "~/Blanton_Script/TH6_SWB0_power_readback.sh"
     wait prompt_sonic_root
     sendln "~/Blanton_Script/TH6_SWB1_power_readback.sh"
+    wait prompt_sonic_root
+    sendln "~/Blanton_Script/avt_pmpower.sh -p ~/AVT_Linux_NDA_2.8.37/AVTCMD"
 
     ; Background jobs Check
     wait prompt_sonic_root

src/Script_ABC_Blanton/5_Blanton_Script_Boot_Cycle.ttl

@@ -8,8 +8,14 @@ gettime str_starttime "%Y%m%d-%H%M%S"
 getdir mdir
 
 if EN_log = 1 then
-    sprintf2 filename '%s\Logs\%s_%s_%s.log' mdir project_name "Reboot_Cycle" str_starttime
-    logopen filename 0 1 1 1
+    if EN_Cold_Warm_boot = 1 then
+        sprintf2 filename '%s\Logs\%s_%s_%s.log' mdir project_name "Reboot_Cycle" str_starttime
+        logopen filename 0 1 1 1
+    elseif EN_Cold_Warm_boot = 2 then
+        sprintf2 filename '%s\Logs\%s_%s_%s.log' mdir project_name "Power_Cycle" str_starttime
+        logopen filename 0 1 1 1
+    else
+    endif
 endif
 
 cnt_cycle = 0
@@ -26,9 +32,16 @@ while 1
     wait prompt_sonic_root
     sendln "sleep 10"
 
-    wait prompt_sonic_root
-    sprintf2 strTitle "echo -e '\033[1;32mReboot Cycle : %d \033[0m'" cnt_cycle
-    sendln strTitle
+    if EN_Cold_Warm_boot = 1 then
+        wait prompt_sonic_root
+        sprintf2 strTitle "echo -e '\033[1;32mReboot Cycle : %d \033[0m'" cnt_cycle
+        sendln strTitle
+    elseif EN_Cold_Warm_boot = 2 then
+        wait prompt_sonic_root
+        sprintf2 strTitle "echo -e '\033[1;32mPower Cycle : %d \033[0m'" cnt_cycle
+        sendln strTitle
+    else
+    endif
 
     ; ========== Pre Setting ==========
     ; Make log directory
@@ -172,6 +185,8 @@ while 1
     sprintf2 strCKPt5 "echo -e '\033[36mCheck Pt5 : SSD Test\033[0m'"
     sendln strCKPt5
 
+    wait prompt_sonic_root
+    sendln "rm -rf /host/hw-eval/jobs/qfx5252-stress-ssd.log"
     wait prompt_sonic_root
     sendln "qfx5252-stress-ssd 1G --runtime 30 --passes 2 --write --force --log /host/hw-eval/jobs/qfx5252-stress-ssd.log"
     wait prompt_sonic_root
@@ -189,6 +204,8 @@ while 1
     waitregex '<<DEV=([^>]*)>>'
     usb_dev = groupmatchstr1
 
+    wait prompt_sonic_root
+    sendln "rm -rf /host/hw-eval/jobs/qfx5252-stress-usb.log"
     wait prompt_sonic_root
     sprintf2 cmd "qfx5252-stress-usb %s 256M --runtime 30 --passes 2 --write --log /host/hw-eval/jobs/qfx5252-stress-usb.log" usb_dev
     sendln cmd
@@ -412,8 +429,15 @@ while 1
     sendln "show uptime"
 
     ; ========== Show Power on uptime ==========
-    wait prompt_sonic_root
-    sendln "reboot"
+    if EN_Cold_Warm_boot = 1 then
+        wait prompt_sonic_root
+        sendln "reboot"
+    elseif EN_Cold_Warm_boot = 2 then
+        wait prompt_sonic_root
+        sendln "pcimem /sys/bus/pci/devices/0000:05:00.0/resource0 0x480 w 0xD0000"
+    else
+    endif
+
 
     wait "Booting in blind mode"
 endwhile

src/Script_ABC_Blanton/Blanton_Script/avt_pmpower.sh

@@ -0,0 +1,137 @@
+#!/bin/bash
+#===============================================================================
+# Script  : avt_pmpower.sh
+# Purpose : Dump AMD AVT PM table (get_pmdata) and summarize package power.
+#
+# Author  : ETWen
+# Date    : 20260923
+#
+# Version History
+# V1.0.0     20260923    Initial Version
+#
+# Usage   : ./avt_pmpower.sh [-p <AVTCMD path>] [-q] [-h]
+#             -p   Path to AVTCMD (default: $AVTCMD_PATH or ./AVTCMD)
+#             -q   Quiet: summary only, suppress raw PM table
+#             -h   Help
+#
+# Exit    : 0 ok / 1 usage / 2 AVTCMD not found / 3 AVTCMD failed
+#           4 parse failed (no power fields found)
+#
+# Note    : Values come from SMU telemetry, not direct measurement. Absolute
+#           accuracy depends on BIOS SVI telemetry calibration. Cross-check
+#           against VR PMBus READ_POUT when accuracy matters.
+#===============================================================================
+
+set -u
+set -o pipefail
+
+#------------------------------------------------------------------------------
+# Defaults
+#------------------------------------------------------------------------------
+AVTCMD_BIN="${AVTCMD_PATH:-./AVTCMD}"
+AVT_MODULE="pmm"
+AVT_CMD="get_pmdata()"
+QUIET=0
+
+#------------------------------------------------------------------------------
+# usage - print help
+#------------------------------------------------------------------------------
+usage() {
+    sed -n '/^# Usage/,/^# Exit/p' "$0" | sed 's/^# \{0,1\}//'
+}
+
+#------------------------------------------------------------------------------
+# Argument parsing
+#------------------------------------------------------------------------------
+while getopts ":p:qh" opt; do
+    case "$opt" in
+        p) AVTCMD_BIN="$OPTARG" ;;
+        q) QUIET=1 ;;
+        h) usage; exit 0 ;;
+        :) echo "ERROR: -$OPTARG requires an argument" >&2; usage >&2; exit 1 ;;
+        \?) echo "ERROR: unknown option -$OPTARG" >&2; usage >&2; exit 1 ;;
+    esac
+done
+
+#------------------------------------------------------------------------------
+# Pre-flight check
+#------------------------------------------------------------------------------
+if [ ! -x "$AVTCMD_BIN" ]; then
+    echo "ERROR: AVTCMD not found or not executable: $AVTCMD_BIN" >&2
+    echo "       Use -p <path> or export AVTCMD_PATH=<path>" >&2
+    exit 2
+fi
+
+if [ "$(id -u)" -ne 0 ]; then
+    echo "WARN : not running as root, AVTCMD may fail to access SMU." >&2
+fi
+
+#------------------------------------------------------------------------------
+# Collect PM table
+#------------------------------------------------------------------------------
+RAW="$("$AVTCMD_BIN" -module "$AVT_MODULE" "$AVT_CMD" 2>&1)"
+RC=$?
+if [ $RC -ne 0 ]; then
+    echo "ERROR: AVTCMD exited with code $RC" >&2
+    echo "$RAW" >&2
+    exit 3
+fi
+
+if [ "$QUIET" -eq 0 ]; then
+    printf '%s\n' "$RAW"
+fi
+
+#------------------------------------------------------------------------------
+# Parse & summarize
+#   - split on whitespace and comma, keep only "key:number" tokens
+#   - bracketed tokens ([Pkg:0], [MISC]) are skipped by the regex anchor
+#------------------------------------------------------------------------------
+printf '%s\n' "$RAW" | awk '
+{
+    n = split($0, a, /[ ,]+/)
+    for (i = 1; i <= n; i++) {
+        if (a[i] ~ /^[A-Za-z0-9_()]+:[-0-9.]+$/) {
+            split(a[i], kv, ":")
+            m[kv[1]] = kv[2]
+            found++
+        }
+    }
+}
+
+# pct - usage against limit, guard divide-by-zero
+function pct(v, l) {
+    return (l > 0) ? sprintf("%5.1f%%", 100 * v / l) : "  n/a"
+}
+
+# has - field present in PM table
+function has(k) {
+    return (k in m)
+}
+
+END {
+    if (found == 0) {
+        print "ERROR: no PM fields parsed, PM table format may have changed." > "/dev/stderr"
+        exit 4
+    }
+
+    print "===== Package Power (live) ====="
+
+    if (has("SktPwr(W)"))
+        printf "%-9s: %7.2f W\n", "SktPwr", m["SktPwr(W)"]
+
+    if (has("PPT_VALUE_FAST"))
+        printf "%-9s: %7.2f / %3d W  %s\n", "PPT Fast",
+               m["PPT_VALUE_FAST"], m["PPT_LIMIT_FAST"],
+               pct(m["PPT_VALUE_FAST"], m["PPT_LIMIT_FAST"])
+
+    if (has("PPT_VALUE_SLOW"))
+        printf "%-9s: %7.2f / %3d W  %s (%ss avg)\n", "PPT Slow",
+               m["PPT_VALUE_SLOW"], m["PPT_LIMIT_SLOW"],
+               pct(m["PPT_VALUE_SLOW"], m["PPT_LIMIT_SLOW"]),
+               (has("SlowPPTTimeConstant") ? m["SlowPPTTimeConstant"] : "?")
+
+    if (has("MemPwr(W)"))
+        printf "%-9s: %7.2f W\n", "MemPwr", m["MemPwr(W)"]
+}
+'
+exit $?

src/Script_ABC_Blanton/Blanton_Script/bcm_100g_dsc_cycle.sh

@@ -0,0 +1,608 @@
+#!/bin/sh
+# =============================================================================
+# bcm_100g_dsc_cycle.sh
+#
+# Author  : ETWen
+# Date    : 20260909
+#
+# Version History
+# V1.0.0     20260909    Initial Version
+# V1.1.0     20260909    All runtime output is ASCII English - the DUT serial
+#                        console mangles UTF-8 (a Chinese error message came
+#                        back as "ERROR: -c ? 1"). Cycle count may be given as
+#                        a bare argument. Added -d to echo every command, and
+#                        CMD_DELAY to pace them.
+# V1.2.0     20260909    Wait on "bcmcmd ps <port>" instead of
+#                        "show interfaces status". The state comes from the
+#                        SDK, which is what "port en=" actually changes, so it
+#                        no longer depends on gbsyncd syncing into the DB.
+#
+# Description:
+#   Link down/up cycling on the 100G uplink. After every re-link it collects a
+#   SerDes DSC dump and reads the retimer back, so you can see whether the
+#   tuned TX taps settle to the same place each time the link comes up.
+#
+#   One run has two parts:
+#     1. Tuning  -- once. pause gbsyncd -> serdes-tx-set sys 0..7
+#                   -> tx_taps set on four lanes of each unit
+#     2. Cycle   -- repeated N times:
+#                   port en=0 -> wait until "ps <port>" reads !ena on both units
+#                   port en=1 -> wait until "ps <port>" reads up on both units
+#                   phydiag <port> dsc on each unit
+#                   serdes-tx-get / serdes-rx-get sys 0..7
+#                   all of it appended to one log, under a per-cycle heading
+#
+#   Command source: tools/100G_dsc_cycle.txt (the hand-typed bench version).
+#   Change that file and this one together.
+#
+# Deployment:
+#   Script : /root/Blanton_Script/bcm_100g_dsc_cycle.sh
+#   Log    : ~/dsc_log/100G_dsc_cycle_test_<YYYYmmdd_HHMMSS>.log
+#            One file per run, every cycle in it, split by "### TEST CYCLE n/N".
+#
+#   Paths come from $HOME. Run as root (after sudo -i) and ~ is /root.
+#
+# Usage:
+#   ./bcm_100g_dsc_cycle.sh              # print this help
+#   ./bcm_100g_dsc_cycle.sh 200          # 200 cycles
+#   ./bcm_100g_dsc_cycle.sh -c 200       # same thing
+#   ./bcm_100g_dsc_cycle.sh -c 200 -d    # echo every command as it is issued
+#   ./bcm_100g_dsc_cycle.sh -c 10 -T     # skip tuning, cycle only
+#   ./bcm_100g_dsc_cycle.sh -c 1 -n      # dry run, print commands, touch nothing
+#
+# Exit code:
+#   0 = every cycle linked down and up as expected, and all data was collected
+#   1 = a cycle timed out waiting for link, or data was missing
+#   2 = bad argument / path
+#   3 = a required tool is missing (bcmcmd / show / blanton_barchetta_tool)
+#
+#   The last line is always "### DSC_CYCLE_DONE rc=<n>", for a TTL wait to
+#   key on.
+#
+# Design notes:
+#   - POSIX sh. No bash, no Python.
+#   - All runtime output is plain ASCII. The DUT console is not UTF-8 clean:
+#     Chinese comes back as "M-^A"-style garbage, and an error you cannot read
+#     is worse than no error at all. Comments are English for the same reason -
+#     whoever debugs this on the bench is reading it through that console.
+#   - Link state comes from "bcmcmd -n <unit> -c 'ps <port>'". Its header is
+#     two stacked lines, so a column index cannot be derived from it the way
+#     it can from a SONiC table. Instead the data row is found by its first
+#     field ending in "(<port>)" - e.g. ce0(268) - and the state is the field
+#     after it:
+#         ce0(268)  !ena   4  100G  FD ...     <- port disabled
+#         ce0(268)  up     4  100G  FD ...     <- link up
+#     "down" is therefore tested as "not up", which covers !ena as well as an
+#     enabled port whose link has not come back.
+#   - Asking the SDK rather than "show interfaces status" matters here: "port
+#     en=" changes the SDK, and the SONiC table only follows once gbsyncd and
+#     orchagent have synced it into the DB. Since this test pauses gbsyncd,
+#     the SONiC table was the wrong thing to wait on.
+#   - bcmcmd reads stdin, and inside a while loop it will swallow the loop's
+#     input. blanton_traffic_linespeed.sh hit this at v0.3.1 (only the first
+#     VLAN was configured) and bcm_dsc_scan.sh hit it again at v1.3.0 (only
+#     the first port was scanned). Every external command here gets
+#     < /dev/null.
+#   - bcmcmd exits 0 even when the diag shell rejects a command, so the DSC is
+#     verified by counting "SERDES DISPLAY DIAG DATA END", and the retimer read
+#     by counting sections that actually have output under them - not by exit
+#     code, and not by counting headings this script prints itself.
+#
+# Cautions:
+#   - !! While gbsyncd is paused the gearbox state stops being synced into the
+#     DB. The wait reads the SDK directly ("ps <port>") so it is not affected,
+#     but anything you check by hand with "show interfaces status" during the
+#     run may be stale. Set PAUSE_GBSYNCD=0 (or -P) if that gets in the way.
+#   - !! On exit, including Ctrl-C, both gbsyncd containers are unpaused again
+#     so nothing is left paused. Set RESUME_GBSYNCD=0 to keep them paused.
+#   - !! phydiag dsc is read-only, but port en=0/1 and tx_taps set do change
+#     the hardware. Do not run this at the same time as blanton_ber.sh,
+#     blanton_traffic_linespeed or blanton_tr518.sh - they take the same ports.
+#   - !! NOT verified on hardware yet.
+# =============================================================================
+
+set -u
+
+# ----------------------------------------------------------------------------
+# Knobs - change these for a different DUT or port, not the flow below
+# ----------------------------------------------------------------------------
+PORT=268                                  # bcmcmd port number, not a port name
+UNITS="0 1"                               # units to drive
+SYS_LANES="0 1 2 3 4 5 6 7"               # blanton_barchetta_tool sys lanes, tuning
+SYS_TX="pre=-10 main=87 post=0"           # TX setting applied to each of them
+
+# tx_taps, one line per lane: "<unit> <lane> <main> <pre1> <post1>"
+TX_TAPS="
+0 0 31 4 13
+0 1 31 4 13
+0 2 27 4 13
+0 3 29 4 13
+1 0 29 4 13
+1 1 30 4 13
+1 2 31 4 13
+1 3 30 4 13
+"
+
+TX_LANES="0 1 2 3 4 5 6 7"                # retimer TX lanes read back each cycle
+RX_LANES="0 1 2 3 4 5 6 7"                # retimer RX lanes read back each cycle
+
+SUDO=""                                   # set to "sudo" if not running as root
+PAUSE_GBSYNCD=1                           # pause gbsyncd0/1 before tuning
+RESUME_GBSYNCD=1                          # unpause again on exit, Ctrl-C included
+GBSYNCD="gbsyncd0 gbsyncd1"
+
+LINK_WAIT=90                              # give up waiting for a link state after this
+POLL=2                                    # seconds between "ps <port>" reads while waiting
+SETTLE=2                                  # quiet time after link up, before collecting
+CMD_DELAY=0.2                             # pause after every command issued to the DUT
+
+OUTDIR="${HOME:-/root}/dsc_log"
+
+# ----------------------------------------------------------------------------
+CYCLES=0
+DRYRUN=0
+DOTUNE=1
+DEBUG=0
+RC=0
+
+usage() {
+    cat >&2 << 'USAGE'
+Usage: bcm_100g_dsc_cycle.sh <cycles> [options]
+       bcm_100g_dsc_cycle.sh -c <cycles> [options]
+
+  -c <n>      how many cycles to run. May also be given as a bare argument.
+  -o <dir>    log directory (default: ~/dsc_log)
+  -w <sec>    how long to wait for a link state (default: 90)
+  -p <sec>    how often to re-read the port state (default: 2)
+  -s <sec>    quiet time after link up, before collecting (default: 2)
+  -d          debug: echo every command as [CMD] before running it
+  -T          skip tuning, go straight to the cycles
+  -P          leave gbsyncd alone (no pause, no unpause)
+  -n          dry run: print the commands, touch nothing
+  -h          this help
+
+One log per run:
+  ~/dsc_log/100G_dsc_cycle_test_<YYYYmmdd_HHMMSS>.log
+
+Each cycle is one "### TEST CYCLE n/N" section holding, in order: the "ps"
+output showing the port down, the same showing it up, phydiag dsc for both
+units, and the retimer serdes-tx-get / serdes-rx-get for sys 0..7.
+
+Waiting for a port state is a poll, not a single read: "bcmcmd ps <port>" on
+every unit, every -p seconds, until both agree or -w seconds have passed.
+
+Examples:
+  ./bcm_100g_dsc_cycle.sh 200
+  ./bcm_100g_dsc_cycle.sh 200 -d
+  ./bcm_100g_dsc_cycle.sh -c 20 -T -w 120
+USAGE
+    exit 1
+}
+
+[ $# -eq 0 ] && usage
+
+# getopts stops at the first argument that is not an option, so "200 -d" would
+# leave -d unread. Parse, take the bare count, then parse whatever followed it.
+# getopts inside a function reads the function's own arguments; OPTIND is
+# global, so it has to be reset on each entry.
+PARSED=0
+parse_opts() {
+    OPTIND=1
+    while getopts "c:o:w:p:s:dTPnh" opt; do
+        case "$opt" in
+            c) CYCLES="$OPTARG" ;;
+            o) OUTDIR="$OPTARG" ;;
+            w) LINK_WAIT="$OPTARG" ;;
+            p) POLL="$OPTARG" ;;
+            s) SETTLE="$OPTARG" ;;
+            d) DEBUG=1 ;;
+            T) DOTUNE=0 ;;
+            P) PAUSE_GBSYNCD=0; RESUME_GBSYNCD=0 ;;
+            n) DRYRUN=1 ;;
+            *) usage ;;
+        esac
+    done
+    PARSED=$((OPTIND - 1))
+}
+
+parse_opts "$@"
+shift "$PARSED"
+
+# Allow the count as a bare argument: "... 200" == "... -c 200". That is what
+# most people type first, and answering it with an error helps nobody.
+if [ "$CYCLES" = "0" ] && [ $# -ge 1 ]; then
+    case "$1" in
+        -*) : ;;                      # an option; leave it for the second pass
+        *)  CYCLES="$1"; shift ;;     # anything else is meant to be the count,
+    esac                              # and the check below says so if it is not
+fi
+
+# Anything after the count is options again: "200 -d -T"
+if [ $# -gt 0 ]; then
+    parse_opts "$@"
+    shift "$PARSED"
+fi
+
+if [ $# -gt 0 ]; then
+    echo "ERROR: unexpected argument '$1'" >&2
+    echo "       run with no argument to see the usage" >&2
+    exit 2
+fi
+
+case "$CYCLES" in
+    ''|*[!0-9]*)
+        echo "ERROR: cycle count must be a positive integer (got: '$CYCLES')" >&2
+        echo "       try:  $0 200      or  $0 -c 200" >&2
+        exit 2 ;;
+esac
+if [ "$CYCLES" -lt 1 ]; then
+    echo "ERROR: cycle count must be at least 1 (got: $CYCLES)" >&2
+    exit 2
+fi
+
+# ----------------------------------------------------------------------------
+# Colour, only when stdout is a terminal, so a redirected run stays clean
+# ----------------------------------------------------------------------------
+if [ -t 1 ] && [ -z "${NO_COLOR:-}" ]; then
+    C_INFO=$(printf '\033[1;34m')   # blue
+    C_OK=$(printf '\033[1;32m')     # green
+    C_WARN=$(printf '\033[1;33m')   # yellow
+    C_ERR=$(printf '\033[1;31m')    # red
+    C_CMD=$(printf '\033[90m')      # dark grey
+    C_OFF=$(printf '\033[0m')
+else
+    C_INFO=''; C_OK=''; C_WARN=''; C_ERR=''; C_CMD=''; C_OFF=''
+fi
+
+# A dry run touches nothing, so it must not sleep either - otherwise
+# "-c 200 -n" sits there for as long as the real thing would.
+naptime() { [ "$DRYRUN" = "1" ] && return 0; [ "${1:-0}" = "0" ] && return 0; sleep "$1"; }
+
+info() { printf '%s[info]%s %s\n' "$C_INFO" "$C_OFF" "$*"; }
+ok()   { printf '%s[ OK ]%s %s\n' "$C_OK"   "$C_OFF" "$*"; }
+warn() { printf '%s[warn]%s %s\n' "$C_WARN" "$C_OFF" "$*" >&2; }
+err()  { printf '%s[ERR ]%s %s\n' "$C_ERR"  "$C_OFF" "$*" >&2; }
+
+# Both -d and -n print commands. During collection the whole block is
+# redirected into a temp file, so those lines would end up in the file with
+# nothing on screen. Bind fd 9 to the terminal up front and print there.
+if { [ "$DEBUG" = "1" ] || [ "$DRYRUN" = "1" ]; } && ( true > /dev/tty ) 2>/dev/null; then
+    exec 9> /dev/tty
+else
+    exec 9>&1
+fi
+# ':' is a special built-in in dash (the DUT's /bin/sh); a failed redirection
+# on one kills the whole shell with no message. Hence (true > /dev/tty) in a
+# subshell above - if that cannot open, only the subshell dies.
+
+# Print a command the way you would type it: quote any argument that needs it,
+# so the line can be copied back to the prompt as is.
+# NOTE: sh has no local variables - every name assigned here is global. All
+# helper variables are therefore prefixed. _show_cmd used to assign "tag",
+# which silently overwrote the caller's cycle label and turned every later
+# message into "[info] [CMD] : Wait Port Link Down".
+_show_cmd() {
+    _sc_tag="$1"; _sc_col="$2"; shift 2
+    {
+        printf '%s%s%s' "$_sc_col" "$_sc_tag" "$C_OFF"
+        for a in "$@"; do
+            case "$a" in
+                ''|*[!A-Za-z0-9_./=:,+-]*) printf " '%s'" "$a" ;;
+                *)                         printf ' %s' "$a" ;;
+            esac
+        done
+        printf '\n'
+    } >&9
+}
+
+# Every external command goes through here: never reads stdin, echoed when
+# asked, and paced by CMD_DELAY so the DUT is not hammered.
+run() {
+    [ "$DEBUG" = "1" ] && [ "$DRYRUN" = "0" ] && _show_cmd '[CMD]' "$C_CMD" "$@"
+    if [ "$DRYRUN" = "1" ]; then
+        _show_cmd '  +' "$C_CMD" "$@"
+        return 0
+    fi
+    "$@" < /dev/null
+    _cmd_rc=$?
+    naptime "$CMD_DELAY"
+    return $_cmd_rc
+}
+
+# Same, but discards output. Do not write "> /dev/null" at the call site or
+# the [CMD] line goes with it.
+runq() {
+    [ "$DEBUG" = "1" ] && [ "$DRYRUN" = "0" ] && _show_cmd '[CMD]' "$C_CMD" "$@"
+    if [ "$DRYRUN" = "1" ]; then
+        _show_cmd '  +' "$C_CMD" "$@"
+        return 0
+    fi
+    "$@" < /dev/null > /dev/null 2>&1
+    _cmd_rc=$?
+    naptime "$CMD_DELAY"
+    return $_cmd_rc
+}
+
+# ----------------------------------------------------------------------------
+# Preflight
+# ----------------------------------------------------------------------------
+if [ "$DRYRUN" = "0" ]; then
+    command -v bcmcmd > /dev/null 2>&1 || { err "not found: bcmcmd"; exit 3; }
+    # -T only skips tuning; the per-cycle retimer read still needs this tool
+    if [ ! -x /usr/sbin/blanton_barchetta_tool ]; then
+        err "not found: /usr/sbin/blanton_barchetta_tool (tuning and the per-cycle retimer read both use it)"
+        exit 3
+    fi
+fi
+
+# busybox sleep may not take a fraction
+if [ "$DRYRUN" = "0" ] && [ "$CMD_DELAY" != "0" ] && ! sleep "$CMD_DELAY" 2>/dev/null; then
+    warn "sleep '$CMD_DELAY' not supported, falling back to 1"
+    CMD_DELAY=1
+fi
+
+mkdir -p "$OUTDIR" 2>/dev/null || { err "cannot create outdir: $OUTDIR"; exit 2; }
+[ -w "$OUTDIR" ] || { err "outdir not writable: $OUTDIR"; exit 2; }
+
+TS=$(date '+%Y%m%d_%H%M%S')
+LOG="${OUTDIR}/100G_dsc_cycle_test_${TS}.log"
+: > "$LOG" || { err "cannot write $LOG"; exit 2; }
+
+STATUS_TMP=$(mktemp) || { err "mktemp failed"; exit 2; }
+CYCLE_TMP=$(mktemp)  || { err "mktemp failed"; exit 2; }
+
+# ----------------------------------------------------------------------------
+# gbsyncd must go back the way it was found, or the container stays paused
+# ----------------------------------------------------------------------------
+PAUSED=0
+resume_gbsyncd() {
+    [ "$PAUSED" = "1" ] || return 0
+    [ "$RESUME_GBSYNCD" = "1" ] || return 0
+    PAUSED=0
+    for _rg_c in $GBSYNCD; do
+        if runq $SUDO docker unpause "$_rg_c"; then
+            info "gbsyncd resumed: $_rg_c"
+        else
+            warn "docker unpause $_rg_c failed - check it by hand"
+        fi
+    done
+}
+on_exit() { rm -f "$STATUS_TMP" "$CYCLE_TMP"; resume_gbsyncd; }
+on_int()  {
+    echo ""
+    warn "interrupted by user"
+    resume_gbsyncd
+    printf '\n### DSC_CYCLE_DONE rc=130 (INTERRUPTED)\n' >> "$LOG"
+    printf '### DSC_CYCLE_DONE rc=130 (INTERRUPTED)\n'
+    rm -f "$STATUS_TMP" "$CYCLE_TMP"
+    exit 130
+}
+trap on_exit EXIT
+trap on_int INT TERM
+
+tee_log() { tee -a "$LOG"; }
+
+# ----------------------------------------------------------------------------
+# Link state. Find which field "Oper" is from the header row, then read that
+# field on every data row. Returns 0 only when every interface matches.
+# The table itself is left in $STATUS_TMP for the caller to print.
+# ----------------------------------------------------------------------------
+# $1 = "up" or "down". Runs "ps <port>" on every unit, leaves the combined
+# output in $STATUS_TMP for the caller to print, and returns 0 only when every
+# unit agrees.
+link_is() {
+    _li_want="$1"
+    : > "$STATUS_TMP"
+    for _li_u in $UNITS; do
+        printf '\n[unit %s] bcmcmd -n %s -c "ps %s"\n' "$_li_u" "$_li_u" "$PORT" >> "$STATUS_TMP"
+        if [ "$DRYRUN" = "1" ]; then
+            _show_cmd '  +' "$C_CMD" bcmcmd -n "$_li_u" -c "ps $PORT"
+            printf '    ce0(%s)  %s   4  100G  FD  (dry-run)\n' \
+                   "$PORT" "$([ "$_li_want" = up ] && echo 'up  ' || echo '!ena')" >> "$STATUS_TMP"
+            continue
+        fi
+        [ "$DEBUG" = "1" ] && _show_cmd '[CMD]' "$C_CMD" bcmcmd -n "$_li_u" -c "ps $PORT"
+        bcmcmd -n "$_li_u" -c "ps $PORT" < /dev/null >> "$STATUS_TMP" 2>&1
+        naptime "$CMD_DELAY"
+    done
+
+    # The data row is the one whose first field ends in "(<port>)"; the state
+    # is the field right after it. "down" is "not up", so !ena counts.
+    awk -v port="$PORT" -v want="$_li_want" -v units="$(echo "$UNITS" | wc -w)" '
+        $1 ~ ("\\(" port "\\)$") {
+            n++
+            if (want == "up") { if ($2 != "up") bad++ }
+            else              { if ($2 == "up") bad++ }
+        }
+        END { exit (n >= units && bad == 0) ? 0 : 1 }
+    ' "$STATUS_TMP"
+}
+
+# $1 = wanted state (Down/up), $2 = label for the messages
+wait_link() {
+    _wl_want="$1"; _wl_tag="$2"
+    _wl_waited=0
+    while :; do
+        if link_is "$_wl_want"; then
+            {
+                printf '\n--- port %s after %ss ---\n' "$_wl_want" "$_wl_waited"
+                cat "$STATUS_TMP"
+            } | tee_log
+            ok "$_wl_tag : port $_wl_want after ${_wl_waited}s"
+            return 0
+        fi
+        [ "$_wl_waited" -ge "$LINK_WAIT" ] && break
+        naptime "$POLL"
+        _wl_waited=$((_wl_waited + POLL))
+    done
+    {
+        printf '\n--- TIMEOUT waiting for port %s (%ss) ---\n' "$_wl_want" "$LINK_WAIT"
+        cat "$STATUS_TMP"
+    } | tee_log
+    err "$_wl_tag : TIMEOUT waiting for port $_wl_want (${LINK_WAIT}s)"
+    return 1
+}
+
+port_en() {
+    for _pe_u in $UNITS; do
+        runq bcmcmd -n "$_pe_u" -c "port ${PORT} en=$1"
+    done
+}
+
+# ----------------------------------------------------------------------------
+# Log header
+# ----------------------------------------------------------------------------
+{
+    printf '=====================================================================\n'
+    printf '100G DSC cycle test\n'
+    printf '  script   : bcm_100g_dsc_cycle.sh V1.2.0\n'
+    printf '  started  : %s\n' "$(date '+%Y-%m-%d %H:%M:%S')"
+    printf '  cycles   : %s\n' "$CYCLES"
+    printf '  port     : %s   units : %s\n' "$PORT" "$UNITS"
+    printf '  tuning   : %s\n' "$([ "$DOTUNE" = 1 ] && echo yes || echo 'skipped (-T)')"
+    printf '  tx lanes : %s\n' "$TX_LANES"
+    printf '  rx lanes : %s\n' "$RX_LANES"
+    printf '  link wait: %ss   poll %ss   settle %ss   cmd delay %ss\n' \
+           "$LINK_WAIT" "$POLL" "$SETTLE" "$CMD_DELAY"
+    printf '=====================================================================\n'
+} >> "$LOG"
+
+info "log : $LOG"
+
+# ----------------------------------------------------------------------------
+# 1. Tuning, once
+# ----------------------------------------------------------------------------
+if [ "$DOTUNE" = "1" ]; then
+    info "Tuning"
+    printf '\n### TUNING  %s\n' "$(date '+%Y-%m-%d %H:%M:%S')" >> "$LOG"
+
+    if [ "$PAUSE_GBSYNCD" = "1" ]; then
+        for c in $GBSYNCD; do
+            if runq $SUDO docker pause "$c"; then
+                PAUSED=1
+                info "gbsyncd paused: $c"
+            else
+                warn "docker pause $c failed (container not running?)"
+            fi
+        done
+    fi
+
+    run $SUDO /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 0 2>&1 | tee_log
+
+    for l in $SYS_LANES; do
+        # shellcheck disable=SC2086
+        run $SUDO /usr/sbin/blanton_barchetta_tool --serdes-tx-set sys "$l" $SYS_TX 2>&1 | tee_log
+    done
+
+    echo "$TX_TAPS" | while read -r u lane main pre1 post1; do
+        [ -n "${u:-}" ] || continue
+        run bcmcmd -n "$u" -c \
+            " dsh -c 'phydiag ${PORT} tx_taps set lane=${lane} main=${main} pre1=${pre1} post1=${post1}' " \
+            2>&1 | tee_log
+    done
+
+    ok "Tuning done"
+fi
+
+# ----------------------------------------------------------------------------
+# 2. Test cycles
+# ----------------------------------------------------------------------------
+n=1
+while [ "$n" -le "$CYCLES" ]; do
+    tag="Test Cycle $n / $CYCLES"
+
+    printf '\n\n### TEST CYCLE %s/%s  %s\n' "$n" "$CYCLES" \
+           "$(date '+%Y-%m-%d %H:%M:%S')" >> "$LOG"
+
+    # ---- Disable Port ------------------------------------------------------
+    info "$tag : Disable Port"
+    port_en 0
+
+    info "$tag : Wait Port Link Down"
+    wait_link down "$tag" || RC=1
+
+    # ---- Enable Port -------------------------------------------------------
+    info "$tag : Enable Port"
+    port_en 1
+
+    info "$tag : Wait Link up"
+    if wait_link up "$tag"; then
+        naptime "$SETTLE"
+    else
+        RC=1
+    fi
+
+    # ---- Collect -----------------------------------------------------------
+    # Written to a per-cycle temp file first, then appended. Appending to the
+    # log and then re-reading it to check would mean re-reading an ever larger
+    # file every round - O(n^2) over 200 cycles.
+    info "$tag : Collect Data"
+    : > "$CYCLE_TMP"
+    for u in $UNITS; do
+        {
+            printf '\n--- phydiag %s dsc : unit %s ---\n' "$PORT" "$u"
+            run bcmcmd -n "$u" -c "dsh -c 'phydiag ${PORT} dsc'" 2>&1
+        } >> "$CYCLE_TMP"
+    done
+
+    info "$tag : Read Retimer TX"
+    for l in $TX_LANES; do
+        {
+            printf '\n--- serdes-tx-get sys %s ---\n' "$l"
+            run $SUDO /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys "$l" 2>&1
+        } >> "$CYCLE_TMP"
+    done
+
+    info "$tag : Read Retimer RX"
+    for l in $RX_LANES; do
+        {
+            printf '\n--- serdes-rx-get sys %s ---\n' "$l"
+            run $SUDO /usr/sbin/blanton_barchetta_tool --serdes-rx-get sys "$l" 2>&1
+        } >> "$CYCLE_TMP"
+    done
+
+    cat "$CYCLE_TMP" >> "$LOG"
+
+    if [ "$DRYRUN" = "0" ]; then
+        # bcmcmd exits 0 even when it failed, so count the end marker instead
+        got=$(grep -c 'SERDES DISPLAY DIAG DATA END' "$CYCLE_TMP" 2>/dev/null || true)
+        want=$(echo "$UNITS" | wc -w)
+        if [ "${got:-0}" -lt "$want" ]; then
+            err "$tag : got only ${got:-0}/${want} DSC dumps"
+            RC=1
+        fi
+
+        # The section headings are printed by this script, so counting them
+        # only proves the loop ran. Count sections that have output under them.
+        for d in tx rx; do
+            case "$d" in
+                tx) wantl="$TX_LANES" ;;
+                rx) wantl="$RX_LANES" ;;
+            esac
+            got_l=$(awk -v pat="--- serdes-${d}-get sys " '
+                index($0, pat) == 1 { if (insec && body) ok++; insec = 1; body = 0; next }
+                /^--- / || /^### / { if (insec && body) ok++; insec = 0; next }
+                insec && NF { body = 1 }
+                END { if (insec && body) ok++; print ok + 0 }
+            ' "$CYCLE_TMP")
+            want_l=$(echo "$wantl" | wc -w)
+            if [ "${got_l:-0}" -lt "$want_l" ]; then
+                err "$tag : retimer $(echo "$d" | tr 'a-z' 'A-Z') returned data for only ${got_l:-0}/${want_l} lanes"
+                RC=1
+            fi
+        done
+    fi
+
+    n=$((n + 1))
+done
+
+resume_gbsyncd
+
+printf '\n### DSC_CYCLE_DONE rc=%s\n' "$RC" >> "$LOG"
+if [ "$RC" = "0" ]; then
+    ok "all $CYCLES cycles done -> $LOG"
+else
+    err "some cycles did not complete as expected - see $LOG"
+fi
+printf '### DSC_CYCLE_DONE rc=%s\n' "$RC"
+exit "$RC"

src/Script_ABC_Blanton/Blanton_Script/bcm_dsc_scan.sh

@@ -12,6 +12,9 @@
 #                        避免灌爆 Tera Term logopen 的 log
 # V1.2.0     20260906    新增 -f 自訂 log 檔名(支援 %u / %t 佔位符)與
 #                        -F 強制覆蓋;預設不覆蓋既有檔案,自動加序號
+# V1.3.0     20260907    修正 bcmcmd 讀取 stdin 導致掃描迴圈在第一筆之後
+#                        提前結束的問題(迴圈改用 fd 3,bcmcmd 導向
+#                        /dev/null);新增實際迭代筆數與清單筆數的檢查
 #
 # Description:
 #   在 Blanton SONiC DUT 上批次執行 Broadcom diag shell 的
@@ -278,16 +281,18 @@ for U in $UNITS; do
     : > "$LOG" || { echo "ERROR: cannot write $LOG" >&2; exit 2; }
     LOGS="$LOGS $LOG"
 
-    printf '### SCAN_BEGIN unit=%s time=%s total=%s script=bcm_dsc_scan_V1.1.0\n' \
+    printf '### SCAN_BEGIN unit=%s time=%s total=%s script=bcm_dsc_scan_V1.3.0\n' \
         "$U" "$(date '+%Y-%m-%d %H:%M:%S')" "$TOTAL" >> "$LOG"
 
     echo "[unit $U] scanning $TOTAL ports -> $LOG" >&2
 
     SEQ=0
-    while IFS=, read -r P SPD; do
+    while IFS=, read -r P SPD <&3; do
         SEQ=$((SEQ + 1))
         printf '### PORT unit=%s port=%s speed=%s seq=%s/%s\n' "$U" "$P" "$SPD" "$SEQ" "$TOTAL" >> "$LOG"
-        bcmcmd -n "$U" -c "dsh -c 'phydiag $P dsc'" >> "$LOG" 2>&1 || RC=1
+        # bcmcmd 會讀取 stdin,若不導成 /dev/null 會把 PORTFILE 剩餘內容吸走,
+        # 導致迴圈在第一筆之後就讀到 EOF 而提前結束。
+        bcmcmd -n "$U" -c "dsh -c 'phydiag $P dsc'" >> "$LOG" 2>&1 < /dev/null || RC=1
 
         if [ "$TTY" -eq 1 ]; then
             printf '\r[unit %s] %s/%s  port=%-5s' "$U" "$SEQ" "$TOTAL" "$P" >&2
@@ -296,19 +301,26 @@ for U in $UNITS; do
         fi
 
         sleep "$DELAY"
-    done < "$PORTFILE"
+    done 3< "$PORTFILE"
 
     [ "$TTY" -eq 1 ] && printf '\n' >&2
     printf '### SCAN_END unit=%s time=%s\n' "$U" "$(date '+%Y-%m-%d %H:%M:%S')" >> "$LOG"
 
-    # 概略檢查:每筆 PORT marker 應對應一個 dsc 區塊
+    # 檢查 1:實際迭代筆數是否等於 port 清單筆數。
+    # 迴圈若因 stdin 被子程序吸走而提前結束,只靠下面的 marker/dump 比對抓不到。
+    if [ "$SEQ" -ne "$TOTAL" ]; then
+        echo "ERROR: unit $U  只跑了 $SEQ/$TOTAL 筆,迴圈提前結束" >&2
+        RC=1
+    fi
+
+    # 檢查 2:每筆 PORT marker 應對應一個 dsc 區塊
     MARK=$(grep -c '^### PORT ' "$LOG" || true)
     DUMP=$(grep -c 'SERDES DISPLAY DIAG DATA END' "$LOG" || true)
     if [ "$MARK" -ne "$DUMP" ]; then
         echo "WARN: unit $U  markers=$MARK  dsc_blocks=$DUMP  (有 port 未取得完整 dump)" >&2
         RC=1
     fi
-    echo "Saved: $LOG  (${DUMP}/${MARK} dumps)" >&2
+    echo "Saved: $LOG  (${DUMP}/${TOTAL} dumps)" >&2
 done
 
 # ----------------------------------------------------------------------------

src/Script_ABC_Blanton/Blanton_Script/blanton_ber.sh

@@ -1,8 +1,31 @@
 #!/usr/bin/env bash
 # =============================================================================
-# blanton_ber.sh  --  SerDes BER test over every cabled port (PRBS via phydiag)
+# blanton_ber.sh  --  SerDes BER test, cabled ports PLUS the 100G uplink
 # =============================================================================
 # Version History:
+#   V1.1.1  2026-09-15  Fix: "the BCM shell rejected 'phydiag ... prbs get'" on
+#                       a run that was in fact working. The rejection check
+#                       grepped the WHOLE output, case-insensitively, for
+#                       ERROR|Invalid|... -- and 'prbs get' prints one line per
+#                       lane, so a lane that had not locked ("PRBS Error!")
+#                       matched. The command was fine; the output was data.
+#                       Two consequences: a good run reported a hard error, and
+#                       the lock-count check that was supposed to judge exactly
+#                       those lanes never ran. Per-lane result lines are now
+#                       excluded from the check, the match is case-sensitive,
+#                       and a real rejection prints the offending line.
+#                       The rejection check had been there since V1.0.0, so
+#                       every earlier run carried the same blind spot.
+#   V1.1.0  2026-09-15  Adds port 268, the 100G uplink, which the old port list
+#                       deliberately skipped (it jumps 256-259 -> 270-308).
+#                       The per-lane table is unchanged; the summary now breaks
+#                       each unit into "200G ports" and "100G p268" plus a
+#                       TOTAL row, so the uplink cannot hide inside a 432-lane
+#                       average. A group that reports no lane at all counts as
+#                       a failure, not a pass - silence on the port under test
+#                       is not a result. Developed on the bench as
+#                       blanton_ber_test.sh and folded back over this file once
+#                       it was proven, so there is one BER script again.
 #   V1.0.1  2026-08-28  Fix: every lane reported NA and the Port column showed
 #                       "NA". bcmcmd returns CRLF, and the BER is the last token
 #                       on its line, so the CR stayed glued to the number: it
@@ -19,8 +42,24 @@
 # =============================================================================
 #
 # This is the WHOLE-SWITCH BER sweep: every cabled port, both lanes, PRBS-31
-# through the SerDes. Not to be confused with port_prbs_monitor.sh, which drives
-# the two 100G uplinks only and polls them continuously.
+# through the SerDes -- and, unlike blanton_ber.sh, the 100G uplink as well.
+# Not to be confused with port_prbs_monitor.sh, which drives the two 100G
+# uplinks only and polls them continuously.
+#
+# The port list is two groups:
+#     BER_PORTS_200G   the cabled 200G ports (432 lanes per unit)
+#     BER_PORTS_100G   the 100G uplink, port 268 = ce0, one per unit
+# They are measured in one phydiag pass, but the summary reports them
+# separately per unit, plus a TOTAL:
+#
+#   Unit     GROUP          LANES    PASS    FAIL      NA  WORST BER   ...
+#   unit 0   200G ports       432     432       0       0  2.07e-08    PASS
+#   unit 0   100G p268          4       4       0       0  1.10e-11    PASS
+#   unit 0   TOTAL            436     436       0       0  2.07e-08    PASS
+#   unit 1   ...
+#
+# A 100G row of "NO DATA" means the uplink reported no lane at all, and is
+# treated as a failure -- silence on the port under test is not a pass.
 #
 # Order of operations (matches tools/BER_Test.txt):
 #     init    phydiag <ports> prbs set p=3        arm PRBS on every lane
@@ -51,7 +90,7 @@
 #   -u|--unit <0|1|all|0,1>  bcmcmd unit(s). Default: $BER_UNITS ("0 1")
 #   -c|--criteria <ber>      report: PASS threshold (default $BER_MAX)
 #   -i|--interval <sec>      start: prbsstat Interval (default $BER_INTERVAL)
-#   -p|--ports <list>        override the port list
+#   -p|--ports <list>        override the whole port list (both groups)
 #   -F|--fail-only           report: list only the lanes that FAIL
 #      --tsv                 report: tab-separated (paste into Excel)
 #      --raw                 report: also print the raw 'prbsstat Ber' output
@@ -63,7 +102,8 @@
 #
 # Environment overrides:
 #   BCMCMD_CMD=bcmcmd  BER_UNITS="0 1"  BER_MAX=1e-6  BER_INTERVAL=30
-#   BER_PORTS="1-24,..."  BER_POLY=p=3  BER_LOG_DIR=/tmp  DEBUG_MODE=1
+#   BER_PORTS="1-24,..."  BER_PORTS_200G=...  BER_PORTS_100G=268
+#   BER_POLY=p=3  BER_LOG_DIR=/tmp  DEBUG_MODE=1
 # =============================================================================
 
 # === Config ==================================================================
@@ -73,7 +113,18 @@ BER_UNITS="${BER_UNITS:-0 1}"        # one DUT = two switch boards (0 and 1)
 # The cabled ports, in bcm logical-port numbering. Same list as
 # blanton_traffic_linespeed.sh's TL_PS_PORTS -- kept as one string so it can be
 # pasted straight from/into a manual phydiag command.
-BER_PORTS="${BER_PORTS:-1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565}"
+#
+# Note the gap: the list runs 256-259 then 270-308, so 260..269 are not in it.
+# 268 is ce0, the 100G uplink, and it is the reason this fork exists.
+BER_PORTS_200G="${BER_PORTS_200G:-1-24,40-96,112-168,184-240,256-259,270-308,310-327,342-380,382-399,414-452,454-471,486-524,526-543,558-565}"
+
+# The 100G uplink. One port per unit -- unit 0 and unit 1 each have their own
+# ce0(268), so a two-unit run measures two of them. Comma-separated if more are
+# ever added; the summary treats everything in here as the "100G" group.
+BER_PORTS_100G="${BER_PORTS_100G:-268}"
+
+# What actually goes on the phydiag command line. -p|--ports overrides the lot.
+BER_PORTS="${BER_PORTS:-${BER_PORTS_200G},${BER_PORTS_100G}}"
 
 BER_POLY="${BER_POLY:-p=3}"          # passed to 'prbs set'
 BER_INTERVAL="${BER_INTERVAL:-30}"   # passed to 'prbsstat STArt Interval='
@@ -111,6 +162,24 @@ _ber_dbg()  { [ "$DEBUG_MODE" = "1" ] && echo -e "\033[90m[DEBG] $*\033[0m" >&2;
 BER_ERR_PAT="${BER_ERR_PAT:-ERROR|Failed to execute|Invalid|Syntax error|Unavailable|Unknown command}"
 BER_BENIGN_PAT="${BER_BENIGN_PAT:-polling socket timeout}"
 
+# A per-lane result line -- "  185 : PRBS OK!..." from 'prbs get', or
+# "  203[1] : 5.05e-09" from 'prbsstat Ber'. These are MEASUREMENTS, never
+# shell diagnostics, and they must be kept out of the rejection check:
+# a lane that did not lock prints its own wording (PRBS Error!, and similar),
+# which a case-insensitive match on "ERROR" reads as the BCM shell refusing
+# the command. That is what turned a perfectly good run into
+#     [ERR ] unit 1: the BCM shell rejected 'phydiag ... prbs get'
+# while init/start/report were in fact working -- and it skipped the
+# lock-count check that was supposed to judge those very lanes.
+BER_LANE_LINE='^[ \t]*[0-9]+(\[[0-9]+\])?[ \t]*:'
+
+# _ber_shell_error <output> -- echo the offending line(s), return 0 if any
+_ber_shell_error() {
+    printf '%s\n' "$1" | tr -d '\r' \
+        | grep -vE "$BER_LANE_LINE" \
+        | grep -E "$BER_ERR_PAT"
+}
+
 # _ber_bcm <unit> <phydiag args...>  -- wraps in dsh -c 'phydiag <ports> ...'
 # echoes the DUT output on stdout, returns 0 ok / 1 failed
 _ber_bcm() {
@@ -125,11 +194,14 @@ _ber_bcm() {
     local out rc
     out=$("$BCMCMD_CMD" -n "$unit" -c "$cmd" </dev/null 2>&1); rc=$?
     printf '%s\n' "$out"
-    if echo "$out" | grep -qiE "$BER_ERR_PAT"; then
+    local why
+    why=$(_ber_shell_error "$out")
+    if [ -n "$why" ]; then
         _ber_err "unit $unit: the BCM shell rejected 'phydiag ... $*'"
+        printf '%s\n' "$why" | sed 's/^/        /' >&2
         return 1
     fi
-    if [ "$rc" -ne 0 ] && ! echo "$out" | grep -qiE "$BER_BENIGN_PAT"; then
+    if [ "$rc" -ne 0 ] && ! printf '%s\n' "$out" | grep -qiE "$BER_BENIGN_PAT"; then
         _ber_err "unit $unit: bcmcmd exited $rc on 'phydiag ... $*'"
         return 1
     fi
@@ -243,13 +315,32 @@ _ber_render() {
         -v FAILONLY="$BER_FAIL_ONLY" \
         -v TSV="$BER_TSV" \
         -v COLOR="$color" \
-        -v SIDE="$side" '
+        -v SIDE="$side" \
+        -v P100="$BER_PORTS_100G" '
     function vc(v) {
         if (!COLOR) return v
         if (v == "PASS") return "\033[32m" v "\033[0m"
         if (v == "FAIL") return "\033[31m" v "\033[0m"
         return "\033[33m" v "\033[0m"
     }
+    # Fold one lane into a group tally. Called once for its own group and
+    # and once for ALL, so the TOTAL row is never a hand-added sum that can
+    # drift away from the parts.
+    function acct(g, verdict, berstr, berval, label) {
+        GN[g]++
+        if (verdict == "PASS")      GP[g]++
+        else if (verdict == "FAIL") GF[g]++
+        else                        GNA[g]++
+        if (berval >= 0 && (!(g in GW) || berval > GW[g])) {
+            GW[g] = berval; GWS[g] = berstr; GWL[g] = label
+        }
+    }
+    function emit(g,   lanes) {
+        lanes = GN[g] + 0
+        printf "SUM %s %d %d %d %d %s %s\n", g, lanes, GP[g] + 0, GF[g] + 0, GNA[g] + 0,
+               (lanes > 0 && (g in GWS)) ? GWS[g] : "-",
+               (lanes > 0 && (g in GWL)) ? GWL[g] : "-" > SIDE
+    }
     BEGIN {
         LIM = MAXBER + 0
         NC = 4
@@ -258,6 +349,18 @@ _ber_render() {
         HDR[3] = "BER";    AL[3] = 1
         HDR[4] = "RESULT"; AL[4] = 1
         worst = -1; worstlane = "-"
+
+        # Expand the 100G list ("268" or "268,270-271") into a lookup, so a lane
+        # can be put in the right group by its port number alone.
+        np = split(P100, pp, /[ ,\t]+/)
+        for (i2 = 1; i2 <= np; i2++) {
+            if (pp[i2] == "") continue
+            if (split(pp[i2], rr, "-") == 2) {
+                for (j2 = rr[1] + 0; j2 <= rr[2] + 0; j2++) IS100[j2] = 1
+            } else {
+                IS100[pp[i2] + 0] = 1
+            }
+        }
     }
     # bcmcmd hands back CRLF. On the cd/traffic report the counter is followed by
     # a delta, so the CR got trimmed with the rest of the line; here the BER is
@@ -282,6 +385,8 @@ _ber_render() {
         seen++
         n++
         PORT[n] = port; LANE[n] = lane; BERS[n] = ber
+        grp = ((port + 0) in IS100) ? "P100" : "P200"
+        GRP[n] = grp
         # a lane that reported something non-numeric has no usable measurement
         if (ber ~ /^[0-9]+(\.[0-9]+)?([eE][-+]?[0-9]+)?$/) {
             v = ber + 0
@@ -290,7 +395,10 @@ _ber_render() {
             if (v > worst) { worst = v; worstlane = port "[" lane "]"; worststr = ber }
         } else {
             V[n] = "NA"; nna++
+            v = -1
         }
+        acct(grp,  V[n], ber, v, port "[" lane "]")
+        acct("ALL", V[n], ber, v, port "[" lane "]")
     }
     END {
         if (seen == 0) {
@@ -327,19 +435,32 @@ _ber_render() {
         }
 
         print ""
-        printf "# lanes measured : %d\n", n
+        printf "# lanes measured : %d   (200G %d, 100G %d)\n", n, GN["P200"] + 0, GN["P100"] + 0
         printf "# %s %d  %s %d  %s %d  (criteria BER < %s)\n", \
                vc("PASS"), npass + 0, vc("FAIL"), nfail + 0, vc("NA"), nna + 0, MAXBER
         if (worst >= 0)
             printf "# worst lane     : %s  %s\n", worstlane, worststr
-        if (SIDE != "" && SIDE != "/dev/null")
-            printf "SUM %d %d %d %d %s %s\n", n, npass + 0, nfail + 0, nna + 0, \
-                   (worst >= 0 ? worststr : "-"), worstlane > SIDE
+        if (GN["P100"] + 0 == 0)
+            printf "# %s the 100G port list (%s) matched no lane in this capture\n", vc("NA"), P100
+        else
+            printf "# 100G p%s      : %s %d  %s %d  %s %d   worst %s %s\n", P100,
+                   vc("PASS"), GP["P100"] + 0, vc("FAIL"), GF["P100"] + 0,
+                   vc("NA"), GNA["P100"] + 0,
+                   ("P100" in GWS) ? GWS["P100"] : "-",
+                   ("P100" in GWL) ? GWL["P100"] : "-"
+        if (SIDE != "" && SIDE != "/dev/null") {
+            emit("P200"); emit("P100"); emit("ALL")
+        }
         exit (nfail || nna) ? 2 : 0
     }' "$log"
 }
 
-# _ber_summary <stamp> -- one table for every unit, printed last
+# _ber_summary <stamp> -- one table for every unit, printed last.
+#
+# Each unit gets three rows: the 200G ports, the 100G uplink on its own, and a
+# TOTAL. Unit 0 and unit 1 each have their own ce0(268), so the 100G row is per
+# unit too -- a bad uplink on one board is what this fork exists to make
+# visible, and averaged into 432 other lanes it would not be.
 _ber_summary() {
     local stamp="$1" unit side g r y n worst=0
     g=$'\033[32m'; r=$'\033[31m'; y=$'\033[33m'; n=$'\033[0m'
@@ -347,27 +468,41 @@ _ber_summary() {
 
     echo ""
     echo "===== summary : all units ====="
-    printf '%-8s %8s %8s %8s %8s  %-12s %-10s %s\n' \
-           "Unit" "LANES" "PASS" "FAIL" "NA" "WORST BER" "WORST LANE" "RESULT"
+    printf '%-8s %-12s %7s %7s %7s %7s  %-12s %-12s %s\n' \
+           "Unit" "GROUP" "LANES" "PASS" "FAIL" "NA" "WORST BER" "WORST LANE" "RESULT"
 
-    local tag lanes pass fail na wber wlane v any=0
+    local tag grp lanes pass fail na wber wlane v any=0 label
     for unit in $BER_UNITS; do
-        side="$BER_LOG_DIR/berside_unit${unit}_${stamp}"
+        side="$BER_LOG_DIR/bertside_unit${unit}_${stamp}"
         [ -r "$side" ] || continue
-        read -r tag lanes pass fail na wber wlane < "$side" 2>/dev/null
-        [ "$tag" = "SUM" ] || continue
-        any=1
-        if [ "${fail:-0}" -gt 0 ] || [ "${na:-0}" -gt 0 ]; then
-            v="${r}FAIL${n}"; worst=2
-        else
-            v="${g}PASS${n}"
-        fi
-        printf '%-8s %8s %8s %8s %8s  %-12s %-10s %b\n' \
-               "unit $unit" "$lanes" "$pass" "$fail" "$na" "$wber" "$wlane" "$v"
+        while read -r tag grp lanes pass fail na wber wlane; do
+            [ "$tag" = "SUM" ] || continue
+            any=1
+            case "$grp" in
+                P200) label="200G ports" ;;
+                P100) label="100G p${BER_PORTS_100G}" ;;
+                ALL)  label="TOTAL" ;;
+                *)    label="$grp" ;;
+            esac
+            # A group with no lanes is not a pass. On the 100G row it means the
+            # uplink never reported -- exactly the case worth flagging.
+            if [ "${lanes:-0}" -eq 0 ]; then
+                v="${y}NO DATA${n}"
+                [ "$grp" = "P100" ] && worst=2
+            elif [ "${fail:-0}" -gt 0 ] || [ "${na:-0}" -gt 0 ]; then
+                v="${r}FAIL${n}"; worst=2
+            else
+                v="${g}PASS${n}"
+            fi
+            printf '%-8s %-12s %7s %7s %7s %7s  %-12s %-12s %b\n' \
+                   "unit $unit" "$label" "$lanes" "$pass" "$fail" "$na" \
+                   "$wber" "$wlane" "$v"
+        done < "$side"
     done
     [ "$any" = "1" ] || echo "  (no unit produced a result)"
     echo ""
     printf 'criteria: BER < %s\n' "$BER_MAX"
+    printf '100G group: port(s) %s -- one per unit\n' "$BER_PORTS_100G"
     echo ""
     return "$worst"
 }
@@ -391,7 +526,7 @@ blanton_ber_report() {
     stamp=$(date +%Y%m%d_%H%M%S 2>/dev/null || echo now)
     for unit in $BER_UNITS; do
         log="$BER_LOG_DIR/prbsber_unit${unit}_${stamp}.log"
-        side="$BER_LOG_DIR/berside_unit${unit}_${stamp}"
+        side="$BER_LOG_DIR/bertside_unit${unit}_${stamp}"
         : > "$side"
         if ! _ber_bcm "$unit" "prbsstat Ber" > "$log" 2>&1; then
             _ber_err "unit $unit: 'prbsstat Ber' failed (see $log)"; worst=1; continue
@@ -409,22 +544,24 @@ blanton_ber_report() {
 
     _ber_summary "$stamp"; rc=$?
     [ "$rc" -gt "$worst" ] && worst=$rc
-    rm -f "$BER_LOG_DIR"/berside_unit*_"${stamp}"
+    rm -f "$BER_LOG_DIR"/bertside_unit*_"${stamp}"
     return "$worst"
 }
 
 # === Help ====================================================================
 blanton_ber_help() {
-    echo -e "\033[1mblanton_ber.sh - SerDes BER test over every cabled port (PRBS via phydiag)\033[0m"
+    echo -e "\033[1mblanton_ber.sh - SerDes BER test: cabled 200G ports + the 100G uplink\033[0m"
     echo ""
     echo -e "  Units    : \033[36m$BER_UNITS\033[0m    poly: \033[36m$BER_POLY\033[0m    interval: \033[36m${BER_INTERVAL}s\033[0m"
     echo -e "  Criteria : BER < \033[36m$BER_MAX\033[0m"
-    echo -e "  Ports    : \033[36m$BER_PORTS\033[0m"
+    echo -e "  200G     : \033[36m$BER_PORTS_200G\033[0m"
+    echo -e "  100G     : \033[36m$BER_PORTS_100G\033[0m   (ce0, one per unit -- reported on its own row)"
     echo ""
     echo -e "\033[1mSubcommands\033[0m"
     echo -e "  \033[33minit\033[0m     prbs set $BER_POLY  +  prbs get (checks every lane locked)"
     echo -e "  \033[33mstart\033[0m    prbsstat STArt Interval=$BER_INTERVAL"
     echo -e "  \033[33mreport\033[0m   prbsstat Ber -> per-lane table + PASS/FAIL + summary"
+    echo -e "           summary splits each unit into 200G ports / 100G p$BER_PORTS_100G / TOTAL"
     echo -e "  \033[33mstop\033[0m     prbsstat STOp"
     echo -e "  \033[33mclear\033[0m    prbs clear  (disarms PRBS -- 'init' again before measuring)"
     echo -e "  \033[33mhelp\033[0m"
@@ -433,7 +570,7 @@ blanton_ber_help() {
     echo -e "  \033[33m-u|--unit\033[0m <0|1|all>   bcmcmd unit(s); 'all' = 0 1  (default: $BER_UNITS)"
     echo -e "  \033[33m-c|--criteria\033[0m <ber>   PASS threshold          (default $BER_MAX)"
     echo -e "  \033[33m-i|--interval\033[0m <sec>   prbsstat Interval       (default $BER_INTERVAL)"
-    echo -e "  \033[33m-p|--ports\033[0m <list>     override the port list"
+    echo -e "  \033[33m-p|--ports\033[0m <list>     override the whole port list (both groups)"
     echo -e "  \033[33m-F|--fail-only\033[0m        report: list only failing lanes"
     echo -e "  \033[33m--tsv\033[0m                 report: tab-separated"
     echo -e "  \033[33m--raw\033[0m                 report: also print the raw output"

src/Script_ABC_Blanton/Blanton_Script/ddr5_temp.sh

@@ -0,0 +1,34 @@
+#!/bin/bash
+#==============================================================================
+# Author  : ETWen
+# Date    : 20260923
+# Purpose : Read DDR5 DIMM temperature from SPD5118 hub (MR49/MR50 @ 0x31)
+# Usage   : ./ddr5_temp_V1.0.1.sh [bus] [addr ...]
+#           default: bus=5, addr=0x50 0x51
+#
+# Version History:
+# V1.0.0     20260923    Initial Version
+# V1.0.1     20260923    Output label "DDR temp"
+#==============================================================================
+
+BUS=${1:-5}
+shift 2>/dev/null
+ADDRS=("$@")
+[[ ${#ADDRS[@]} -eq 0 ]] && ADDRS=(0x50 0x51)
+
+REG_TEMP=0x31
+
+for ADDR in "${ADDRS[@]}"; do
+    raw=$(i2cget -y "$BUS" "$ADDR" "$REG_TEMP" w 2>&1)
+    if [[ $? -ne 0 || ! $raw =~ ^0x[0-9a-fA-F]+$ ]]; then
+        echo "[bus $BUS $ADDR] read fail: $raw"
+        continue
+    fi
+
+    # bit[12:2] = temperature, bit12 = sign, 0.25 C/LSB
+    v=$(( (raw >> 2) & 0x7FF ))
+    (( v & 0x400 )) && v=$(( v - 0x800 ))
+
+    awk -v b="$BUS" -v a="$ADDR" -v r="$raw" -v v="$v" \
+        'BEGIN { printf "[bus %s %s] DDR temp: %.2f C  (raw=%s)\n", b, a, v * 0.25, r }'
+done

src/Script_ABC_Blanton/Blanton_Script/hsc_temp_readback.sh

@@ -0,0 +1,65 @@
+#!/bin/bash
+#==============================================================================
+# Author  : ETWen
+# Date    : 20260923
+# Purpose : Read LTC4287 hot-swap controller temperatures (HSC_MAIN / HSC_STBY)
+#           Select source via 0xF3 (0xEB internal / 0xEF external), then read
+#           READ_TEMPERATURE 0x8D (Kelvin) and convert to Celsius
+# Usage   : ./hsc_temp_readback.sh
+#           bus = BUS (28), HSC_MAIN @ 0x40, HSC_STBY @ 0x45
+#
+# Version History:
+# V1.0.0     20260922    Initial Version
+# V1.0.1     20260923    Add header; fix delay comments (DELAY is 0.5 s, not 100 ms);
+#                        CRLF -> LF (CRLF breaks bash on SONiC)
+#==============================================================================
+
+BUS=28
+DELAY=0.5    # seconds between I2C transactions; ~4 s per run (4 readings x 2)
+
+read_temp() {
+    local addr="$1"
+    local name="$2"
+    local sel="$3"
+
+    # Select temperature source
+    i2ctransfer -f -y "$BUS" w3@"$addr" 0xF3 "$sel" 0x00 > /dev/null
+
+    # DELAY between I2C transactions
+    sleep "$DELAY"
+
+    # Read temperature register 0x8D
+    raw=$(i2cget -f -y "$BUS" "$addr" 0x8D w 2>/dev/null)
+
+    if [ -z "$raw" ]; then
+        printf "%-32s : READ ERROR\n" "$name"
+        sleep "$DELAY"
+        return
+    fi
+
+    # Remove 0x prefix and convert hexadecimal to decimal
+    raw_dec=$((16#${raw#0x}))
+
+    # LTC4287 temperature is in Kelvin
+    temp_c=$(awk "BEGIN {printf \"%.2f\", $raw_dec - 273.15}")
+
+    printf "%-32s : %8s °C  (raw %s)\n" \
+           "$name" "$temp_c" "$raw"
+
+    # DELAY before next I2C transaction
+    sleep "$DELAY"
+}
+
+echo "=========================================================="
+echo "              LTC4287 Temperature Readback"
+echo "=========================================================="
+
+# HSC_MAIN - LTC4287 @ 0x40
+read_temp 0x40 "HSC_MAIN Internal (PU11)" 0xEB
+read_temp 0x40 "HSC_MAIN External (PQ1)"  0xEF
+
+# HSC_STBY - LTC4287 @ 0x45
+read_temp 0x45 "HSC_STBY Internal (PU46)" 0xEB
+read_temp 0x45 "HSC_STBY External (PQ53)"  0xEF
+
+echo "=========================================================="

src/Script_ABC_Blanton/config.ttl

@@ -5,6 +5,8 @@ project_name = "Blanton"
 strTestcase="ENV"      ;ENV,EMC,Margin...etc 
 
 EN_Margin         = 0  ; 1: Enable Margin Test, 0: Disable Margin Test
+EN_TX_FIR         = 0  ; 1: Enable bcm_dsc_scan.sh collect port TX_FIR, 0: Disable (saves ~20 min: ScriptA and ScriptC each scan for ~10 min)
+
 EN_log            = 1  ; 1: Enable log, 0: Disable log
 EN_timestamp      = 1  ; 1: Enable timestamp in log, 0: Disable timestamp in log
 
@@ -32,4 +34,13 @@ BMC_USB_RUNTIME = 172800    ; Unit seconds, 172800 = 2 days
 ;================================================================
 prompt_login = "sonic login:"
 prompt_sonic = "admin@sonic:~$"
-prompt_sonic_root = "root@sonic:~#"
+prompt_sonic_root = "root@sonic:~#"
+
+
+;================================================================
+; Reboot or Power Cycle
+;================================================================
+; 0: Normal Test
+; 1: Enable Reboot Cycle
+; 2: Enable Power Cycle
+EN_Cold_Warm_boot = 0

src/Script_ABC_Blanton/utils/setup_pmon.ttl

@@ -5,6 +5,10 @@ sendln "show platform fan"
 wait prompt_sonic_root
 sendln "show platform temperature"
 wait prompt_sonic_root
+sendln "~/Blanton_Script/ddr5_temp.sh"
+wait prompt_sonic_root
+sendln "~/Blanton_Script/hsc_temp_readback.sh"
+wait prompt_sonic_root
 sendln "show platform psustatus"
 wait prompt_sonic_root
 sendln "show platform voltage"

tools/100G_dsc_cycle.txt

@@ -0,0 +1,90 @@
+cd /usr/sbin
+sudo docker pause gbsyncd1
+sudo docker pause gbsyncd0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 0
+
+//Tuning
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-set sys 0 pre=-10 main=87 post=0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-set sys 1 pre=-10 main=87 post=0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-set sys 2 pre=-10 main=87 post=0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-set sys 3 pre=-10 main=87 post=0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-set sys 4 pre=-10 main=87 post=0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-set sys 5 pre=-10 main=87 post=0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-set sys 6 pre=-10 main=87 post=0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-set sys 7 pre=-10 main=87 post=0
+bcmcmd -n 0 -c " dsh -c 'phydiag 268 tx_taps set lane=0 main=31 pre1=4 post1=13' "
+bcmcmd -n 0 -c " dsh -c 'phydiag 268 tx_taps set lane=1 main=31 pre1=4 post1=13' "
+bcmcmd -n 0 -c " dsh -c 'phydiag 268 tx_taps set lane=2 main=27 pre1=4 post1=13' "
+bcmcmd -n 0 -c " dsh -c 'phydiag 268 tx_taps set lane=3 main=29 pre1=4 post1=13' "
+bcmcmd -n 1 -c " dsh -c 'phydiag 268 tx_taps set lane=0 main=29 pre1=4 post1=13' "
+bcmcmd -n 1 -c " dsh -c 'phydiag 268 tx_taps set lane=1 main=30 pre1=4 post1=13' "
+bcmcmd -n 1 -c " dsh -c 'phydiag 268 tx_taps set lane=2 main=31 pre1=4 post1=13' "
+bcmcmd -n 1 -c " dsh -c 'phydiag 268 tx_taps set lane=3 main=30 pre1=4 post1=13' "
+
+以下Test Cycle 目標200次
+//Disable Port
+bcmcmd -n 0 -c "port 268 en=0"
+bcmcmd -n 1 -c "port 268 en=0"
+
+//Wait Link Down
+bcmcmd -n 0 -c "ps 268"
+bcmcmd -n 1 -c "ps 268"
+root@sonic:~# bcmcmd -n 0 -c "ps 268"
+ps 268
+              ena/        speed/ link auto    STP                  lrn             max    cut                 loop
+        port  link  Lns   duplex scan neg?   state   pause  discrd ops   medium  frame   thru            FEC  back
+    ce0(268)  !ena   4  100G  FD   SW  No   Forward         Untag   FA Backplane  9122   No            RS528
+drivshell>
+root@sonic:~# bcmcmd -n 1 -c "ps 268"
+ps 268
+              ena/        speed/ link auto    STP                  lrn             max    cut                 loop
+        port  link  Lns   duplex scan neg?   state   pause  discrd ops   medium  frame   thru            FEC  back
+    ce0(268)  !ena   4  100G  FD   SW  No   Forward         Untag   FA Backplane  9122   No            RS528
+drivshell>
+root@sonic:~#
+
+
+//Enable Port
+bcmcmd -n 0 -c "port 268 en=1"
+bcmcmd -n 1 -c "port 268 en=1"
+
+//Wait Link Up
+bcmcmd -n 0 -c "ps 268"
+bcmcmd -n 1 -c "ps 268"
+root@sonic:~# bcmcmd -n 0 -c "ps 268"
+ps 268
+              ena/        speed/ link auto    STP                  lrn             max    cut                 loop
+        port  link  Lns   duplex scan neg?   state   pause  discrd ops   medium  frame   thru            FEC  back
+    ce0(268)  up     4  100G  FD   SW  No   Forward         Untag   FA Backplane  9122   No            RS528
+drivshell>
+root@sonic:~# bcmcmd -n 1 -c "ps 268"
+ps 268
+              ena/        speed/ link auto    STP                  lrn             max    cut                 loop
+        port  link  Lns   duplex scan neg?   state   pause  discrd ops   medium  frame   thru            FEC  back
+    ce0(268)  up     4  100G  FD   SW  No   Forward         Untag   FA Backplane  9122   No            RS528
+drivshell>
+root@sonic:~#
+
+
+//Collect DSC Data
+bcmcmd -n 0 -c "dsh -c 'phydiag 268 dsc'"
+bcmcmd -n 1 -c "dsh -c 'phydiag 268 dsc'"
+
+//讀Retimer TX/RX
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 1
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 2
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 3
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 4
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 5
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 6
+sudo /usr/sbin/blanton_barchetta_tool --serdes-tx-get sys 7
+
+sudo /usr/sbin/blanton_barchetta_tool --serdes-rx-get sys 0
+sudo /usr/sbin/blanton_barchetta_tool --serdes-rx-get sys 1
+sudo /usr/sbin/blanton_barchetta_tool --serdes-rx-get sys 2
+sudo /usr/sbin/blanton_barchetta_tool --serdes-rx-get sys 3
+sudo /usr/sbin/blanton_barchetta_tool --serdes-rx-get sys 4
+sudo /usr/sbin/blanton_barchetta_tool --serdes-rx-get sys 5
+sudo /usr/sbin/blanton_barchetta_tool --serdes-rx-get sys 6
+sudo /usr/sbin/blanton_barchetta_tool --serdes-rx-get sys 7